• Korean Journal of Remote Sensing
• /
• v.38 no.2
• /
• pp.215-222
• /
• 2022

In this study, the effect of wavelength range and absorption cross-section used to retrieve nitrogen dioxide (NO₂) vertical column density (VCD) from Pandora was analyzed using Differential Optical Absorption Spectroscopy (DOAS). During the GEMS Map of the Air Pollution (GMAP) 2020 campaign, data from direct sunlight observation with Pandora instrument in Seosan was used, and NO₂ VCD was retrieved under four conditions. The average NO₂ VCD under the four conditions ranged from 1.22×10¹⁶~1.38×10¹⁶ molec. cm^-2, with a maximum difference of 0.16×10¹⁶ molec. cm^-2 between each condition. The fitting error averaged 3.19~9.59%, showing an error within 10% in all cases, and the RMS was 5.11×10^-3~7.16×10^-3 molec. cm^-2. The retrieved NO₂ VCD using 4 conditions shows a slope in the range of 0.98 to 1.09 and correlation of 0.96 to 0.98 in comparison with Pandonia Global Network (PGN).

• Korean Chemical Engineering Research
• /
• v.59 no.2
• /
• pp.239-246
• /
• 2021

Characteristics of hydrodynamics and heat absorption by gas in a directly-irradiated fluidized bed particle receiver (50 mm-ID X 150 mm high) of SiC particles have been determined. Solid holdups of SiC particles show almost constant values with increasing gas velocity. Fine SiC particles (SiC II; dp=52 ㎛, ρs=2992 kg/㎥) showed low values of relative standard deviation of pressure drop across bed but high solids holdups in the freeboard region compared to coarse SiC particles (SiC I; dp=123 ㎛, ρs=3015 kg/㎥). The SiC II exhibited higher values of temperature difference normalized by irradiance due to the effect of additional solar heat absorption and heat transfer to the gas by the particles entrained in the freeboard region in addition to the efficient thermal diffusion of the solar heat received at bed surface. Heat absorption rate and efficiency increased with increasing the gas velocity and fluidization number. The SiC II showed maximum heat absorption rate of 17.8 W and thermal efficiency of 14.8%, which are about 33% higher than those of SiC I within the experimental gas velocity range.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.20 no.1
• /
• pp.4575-4591
• /
• 1978

In order to investigate the effects of grain size distribution, cement content, and molding pressure on the strength and durability of soil-cement mixtures, a laboratory test of soil cement mixtures was performed at four levels of cement content, five levels of molding pressure, and four levels of normal curing periods. The results are summarized as follows: 1. Optimum moisture contents in loam soil and maximum dry density in sand soil increased with the increase of cement content, but in others, both optimum moisture contents and maximum dry density were changed ununiformly. 2. When the specimens were molded with molding pressure, 50kg/$\textrm{cm}^2$, strength of soil cement mixture with cement content, 2 and 4 per cent, was lower than the strength of soil cement mixture without cement content by more than 40 to 50 per cent. 3. The strength of soil-cement molded with molding pressure, 100kg/$\textrm{cm}^2$, was higher than the strength of soil-cement molded with M.D.D. obtained from standard compaction test more than 40 per cent in sand loam cement and 50 per cent in loamy cement. 4. There was highly significant positive correlation among molding pressure, cement content and unconfined compressive strentgh and so the following multiple regression equations were obtained. Loam: fc=1.9693C+0.197P-0.84 Sandy loam: fc=2.9065C+0.235P-0.77 5. When the specimens were molded with molding pressure, 20 to 100kg/$\textrm{cm}^2$, the regression equation between the 28-day and 7-day strenght was obtained as follows. Loam : q28=1.1050q7+7.59(r=0.9147) Sandy loam : q28=1.3905q7+3.17 (r=0.9801) 6. At the cement contents of above 50 per cent, the weight losses by freeeze-thaw test were negligible. At the cement content of below 8 per cent the weight losses were singnificantly high under low molding pressure and remarkably decreased with the increase of molding pressure up to 80kg/$\textrm{cm}^2$. 7. Resistance to damage from water and to absorption of water were not improved by molding pressure alone, but when the soil was mixtured with cement above 6 per cent, damage seldoms occurred and absorbed less than 5 per cent of water. 8. There was highly significant inverse-corelationship between the compressive strength of soil cement mixtures and their freeze-thaw loss as well as water absorption. By the regression equation methods, the relationships between them were expessed as followed fc=-7.3206Wa+115.6(r=0.9871) log fc=-0.0174L+1.59(r=0.7709) where fc=unconfined compressive stregth after 28-days curing. kg/$\textrm{cm}^2$ Wa=water absorption, % L : freeze-thaw loss rate, %

• The Korean Journal of Nuclear Medicine Technology
• /
• v.17 no.2
• /
• pp.10-14
• /
• 2013

Purpose: Due to developed simultaneous PET/MRI, it has become possible to obtain more anatomical image information better than conventional PET/CT. By the way, in the PET/CT, the linear absorption coefficient is measured by X-ray directly. However in case of PET/MRI, the value is not measured from MRI images directly, but is calculated by dividing as 4 segmentation ${\mu}-map$. Therefore, in this paper, we will evaluate the SUV's difference of attenuation correction PET images from PET/MRI and PET/CT. Materials and Methods: Biograph mCT40 (Siemens, Germany), Biograph mMR were used as a PET/CT, PET/MRI scanner. For a phantom study, we used a solid type $^{68}Ge$ source, and a liquid type $^{18}F$ uniformity phantom. By using VIBE-DIXON sequence of PET/MRI, human anatomical structure was divided into air-lung-fat-soft tissue for attenuation correction coefficient. In case of PET/CT, the hounsfield unit of CT was used. By setting the ROI at five places of each PET phantom images that is corrected attenuation, the maximum SUV was measured, evaluated %diff about PET/CT vs. PET/MRI. In clinical study, the 18 patients who underwent simultaneous PET/CT and PET/MRI was selected and set the ROI at background, lung, liver, brain, muscle, fat, bone from the each attenuation correction PET images, and then evaluated, compared by measuring the maximum SUV. Results: For solid $^{68}Ge$ source, SUV from PET/MRI is measured lower 88.55% compared to PET/CT. In case of liquid $^{18}F$ uniform phantom, SUV of PET/MRI as compared to PET/CT is measured low 70.17%. If the clinical study, the background SUV of PET/MRI is same with PET/CT's and the one of lung was higher 2.51%. However, it is measured lower about 32.50, 40.35, 23.92, 13.92, 5.00% at liver, brain, muscle, fat, femoral head. Conclusion: In the case of a CT image, because there is a linear relationship between 511 keV ${\gamma}-ray$ and linear absorption coefficient of X-ray, it is possible to correct directly the attenuation of 511 keV ${\gamma}-ray$ by creating a ${\mu}$map from the CT image. However, in the case of the MRI, because the MRI signal has no relationship at all with linear absorption coefficient of ${\gamma}-ray$, the anatomical structure of the human body is divided into four segmentations to correct the attenuation of ${\gamma}-rays$. Even a number of protons in a bone is too low to make MRI signal and to localize segmentation of ${\mu}-map$. Therefore, to develope a proper sequence for measuring more accurate attenuation coefficient is indeed necessary in the future PET/MRI.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5384-5393
• /
• 2015

We investigated the effects of milling degrees of rice on characteristics of the steamed rice and fermentation of rice koji as a raw material of cheongju. It was studied for 8 months about ratio of water absorption and koji charateristics according to milling degrees. The The more increasing rice milling, the less the protein contents of milled rice was continuously decreased and the lipid and ash contents were sharply decreased to until the milling degrees 20%, and then gradually decreased. When steeping the milled rice, higher milling degrees raised rapid water asorption and higher maximum water asorption, lower water temperature raised gradual water absorption and higher maximum absorption. The longer steeping time, the steamed rice milling degrees 40% showed significantly lower hardness and springness than others. Alcohol contents of the fermented mash with rice koji milling degrees 10% was lower with 16.3-16.9%(v/v) than other sample's 17.1-17.5% (v/v). The total acid contents showed that the milling degrees 10% indicated the lowest content(0.71-0.76%) and the milling degrees 30% indicated highest content(0.93-0.99%). Within the same milling degrees, As the steeping time increases, the total acid contents imcrease. In conclusion, the milling degrees influenced on physicochemical chatacteristics of rice and steamed rice condition.

• Journal of Ginseng Research
• /
• v.44 no.4
• /
• pp.627-636
• /
• 2020

Background: Cultivation of medicinal crops, which synthesize hundreds of substances for curative functions, was focused on the synthesis of secondary metabolites rather than biomass accumulation. Nutrition is an important restrict factor for plant growth and secondary metabolites, but little attention has been given to the plasticity of nutrient uptake and secondary metabolites synthesis response to soil nitrogen (N) change. Methods: Two year-field experiments of Sanqi (Panax notoginseng), which can synthesize a high level of saponin in cells, were conducted to study the effects of N application on the temporal dynamics of biomass, nutrient absorption, root architecture and the relationships between these parameters and saponin synthesis. Results: Increasing N fertilizer rates could improve the dry matter yields and nutrient absorption ability through increasing the maximum daily growth (or nutrient uptake) rate. Under suitable N level (225 kg/ha N), Sanqi restricted the root length and surface and enhanced the root diameter and N uptake rate per root length (NURI) to promote nutrient absorption, but the opposite status of Sanqi root architecture and NURI was found when soil N was deficient. Furthermore, increasing N rates could promote the accumulation of saponin in roots through improving the NURI, which showed a significant positive relationship with the content of saponin in the taproots. Conclusion: Appropriate N fertilizer rates could optimize both root architecture and nutrient uptake efficiency, then promote both the accumulation of dry matter and the synthesis of saponins.

• Journal of Korean Society of Forest Science
• /
• v.104 no.4
• /
• pp.649-656
• /
• 2015

The objective of this study was to analyze the optimal thinning regimes for timber or carbon managements in Cryptomeria japonica stands of Hannam Experimental Forest, Korea Forest Research Institute. In solving the problem, PATH algorithm, developed by Paderes and Brodie, was used as the decision-making tool and the individual-tree/distance-free stand growth simulator for the species, developed by Kwon et al., was used to predict the stand growth associated with density control by thinning regimes and mortality. The results of this study indicate that the timber management for maximum net present value (NPV) needs less number of but higher intensity thinnings than the carbon management for maximum carbon absorption does. In case of carbon management, the amount of carbon absorption is bigger than that of timber management by about 6% but NPV is reduced by about 3.2%. On the other hand, intensive forest managements with thinning regimes promotes net income and carbon absorption by about 60% compared with those of the do-nothing option.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.6
• /
• pp.42-49
• /
• 2020

This paper is a basic study to improve durability by imparting hydrophobicity to the surface and sphere of cement-based materials. A cement mortar to which a silane/siloxane-based mixed water repellent was added was prepared, and its initial hydration performance, flow performance, and compressive strength were measured. In addition, after the surface was abraded, the water contact angle and water absorption were measured. The flow of cement mortar to which the water repellent was added was found to decrease up to 1.5% in the addition amount of the water repellent agent, and increased at 3.0% in the addition amount. It was found that the setting time of the cement paste was delayed in both the initial setting and the termination when the water repellent was added. It was found that the compressive strength decreased from 3.0% of the maximum added amount of the water repellent to a maximum of 30%. The contact angle was found to increase when the water repellent was added to the cement mortar, and the contact angle after surface polishing was found to be larger than before surface polishing. The addition of the water repellent showed hydrophobicity not only on the surface but also on the surface and cross section damaged by polishing. The water absorption rate was found to decrease when the water repellent was added to the cement mortar, and the water absorption rate after surface polishing was found to be greater than before surface polishing.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.9
• /
• pp.2609-2615
• /
• 2013

A series of fluorene-carbazole copolymers containing the pendant phosphor chromophore $Ir(absn)_2(acac)$ (absn: 2-(1-naphthyl)benzothiazole; acac: acetylacetone) were designed and synthesized via Yamamoto coupling. In the film state, these copolymers exhibited absorption and emission peaks at approximately 389 and 426 nm, respectively, which originated from the fluorene backbone. However, in electroluminescent (EL) devices, a significantly red-shifted emission at approximately 611 nm was observed, which was attributed to the pendant iridium(III) complex. Using these copolymers as a single emission layer, polymer light-emitting devices with ITO/PEDOT:PSS/polymer:DNTPD/TmPyPb/LiF/Al configurations exhibited a saturated red emission at 611 nm. The attached iridium(III) complex had a significant effect on the EL performance. A maximum luminous efficiency of 0.85 cd/A, maximum external quantum efficiency of 0.77, maximum power efficiency of 0.48 lm/W, and maximum luminance of 883 $cd/m^2$ were achieved from a device fabricated with the copolymer containing the iridium(III) complex in a 2% molar ratio.

• Korean journal of food and cookery science
• /
• v.24 no.6
• /
• pp.757-762
• /
• 2008

In this study, korean wheat composite flour and dough were prepared with 1.5, 3.0, 4.5, and 6% Nelumbo nucifera G. tea powder(NNTP). The samples and a control were then compared qualitatively in terms of moisture, protein, ash, and wet gluten content. The farinogram, amylogram, and extensogram characteristics of the dough were also examined, in order to determine the optimal ratio of NNTP for the formulation. According to our results, the moisture content of the flour decreased with increasing NSPP content, whereas its protein and ash content, resistance, and R/E ratio at 135 min of extensogram increased. The NNTP samples had a significantly higher water absorption and weakness of farinogram and maximum resistance at 45, 90, and 135 min. Additionally, samples had an R/E ratio at 45 min of extensogram, 90 min less than the control group. However, stability of the farinogram, temperature of maximum and maximum viscosity of the amylogram, and extensibility of the extensogram showed the reverse effect. The control and NNTP samples showed significant differences in gelatinization beginning temperature of the amylogram, while development time of the farinogram was not significantly different. With regard to the extensogram characteristics of the dough, the area of the control and 1.5% NNTP increased with increasing testing time, whereas at 3.0, 4.5 and 6.0% NNTP, extensibility, and resistance, maximum resistance, and R/E ratio of control and NNTP samples decreased. An area of 3.0, 4.5 and 6.0% NNTP and extensibility of 1.5% NNTP were not significantly different among the testing times. In conclusion, these results show that 1.5% NNTP may prove very useful as a substitute for korean wheat flour where the production of korean wheat white bread is concerned. It may also provide good nutritional and functional properties.