• 전자공학회논문지 IE
• /
• v.47 no.1
• /
• pp.1-5
• /
• 2010

This paper presents new results of the impact of gate structure on hot-carrier-induced performance degradation in SOI low noise amplifier. Circuit simulations were carried out using the measured S-parameters of H--gate and T-gate SOI MOSFETs and Agilent's Advanced Design System (ADS) to compare the performance of H-gate LNA and T-gate LNA before and after stress. We will discuss the figure of merit for the characterization of low noise amplifier in terms of impedance matching (S11), noise figure, and gain as well as the relation between device degradation and performance degradation of LNA.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.4
• /
• pp.59-63
• /
• 2014

Previous studies have selected wireless power transmission system using 2.45 GHz of ISM band, but the researches for 5.8 GHz microwave wireless power transmission have been relatively rare. The 5.8 GHz has some advantages compared with 2.45 GHz. Those are smaller antenna and smaller integrated system for RFIC. In this paper, the 5.8 GHz wireless power transmission system was developed and transmission efficiency was measured according to the distance. A transmitter sent the amplified microwaves through an antenna amplified by a power amplifier of 1W for 5.8 GHz, and a receiver was converted to DC from RF through a RF-DC Converter. In the 1W 5.8GHz wireless power transmission system, the converted currents and voltages were measured to evaluate transmission efficiency at each distance where LED lights up to 1m. The RF-DC Converter is designed and fabricated by impedance matching using full-wave rectifier circuit. The transmission-efficiency of the system shows from 1.05% at 0cm to 0.095% at 100cm by distance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.6 s.121
• /
• pp.584-590
• /
• 2007

In this paper, the efficiency of power amplifier has been maximized by the application of EER structure, and the linearity has been improved by using PBG structure. This paper has proposed a design of power amplifier in class-F to get the PAE, and to control dynamic power using envelope detector. PBG structure gets high-linearity by removing harmonics arisen from the mismatching of matching circuit. The PAE and the 3rd order IMD have been improved 34.64%, 6.65 dB compared with those of conventional Doherty amplifier, respectively.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.11
• /
• pp.1215-1220
• /
• 2014

In this paper, a local oscillator for X-band radar system is designed and fabricated with GaAs MESFET. GaAs MESFET is good for microwave oscillators because of very low noise figure and high electron mobility. Oscillator design methods in this paper are used the characteristic of negative resistance of active component and impedance matching technique without RF resonator. So, oscillator is designed in compact size because space of RF resonator is reduced and can be applied MMIC technique. Designed oscillator has characteristic of the output power of 2.30 dBm and center frequency of 10.545GHz.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.406-412
• /
• 2018

In this paper, we propose a narrow resonant waveguide probe that can improve the measurement sensitivity in near-field scanning microwave microscopy. The probe consists of a metal waveguide incorporating the following two sections: a straight section at the tip of the probe whose cross-section is a double-ridged rectangle, and whose height is much smaller than the waveguide width; and a standard waveguide section. The advantage of the narrow waveguide is the same as that of the quarter-wave transformer section i.e., it achieves impedance-matching between the sample under test (SUT) and the standard waveguide. The design procedure used for the probe is presented in detail and the performance of the designed resonant probe is evaluated theoretically by using an equivalent circuit. The calculated results are compared with those obtained using the finite element method (Ansoft HFSS), and consistency between the results is demonstrated. Furthermore, the performance of the fabricated resonant probe is evaluated experimentally. At X-band frequencies, we have measured the one-dimensional scanning reflection coefficient of the SUT using the probe. The sensitivity of the proposed resonant probe is improved by more than two times as compared to a conventional waveguide cavity type probe.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.3
• /
• pp.353-358
• /
• 1998

This paper presents development of a LNA operating at 1.71 ∼ 1.18 GHz used for a receiver of KOREA PCS base station and transponder. Using resistive decoupling circuits, a signal at low frequency is dissipated by a resistor. This design method increases the stability of the LNA and suitable for input stage matching. The LNA consists of low noise GaAs FET ATF-10136 and internally matched VNA-25. The LNA is fabricated with both the RF circuit and the self-bias circuits in aluminum housing. As a result, the characteristics of the LNA implemented here shows 30 dB in gain and 0.85 dB in noise figure.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.67-76
• /
• 2000

In this paper, a low noise amplifier has been developed, which is operating at L-band i.e., 1525-1575 MHz. By using resistive decoupling circuits, the resistor dissipates undesired signal in low frequency band. By adopting this design method the stability of the LNA is increased and the input impedance matching is improved. The LNA consists of the low noise GaAs FET ATF-10136 and the internally matched VNA-25. The low LNA is fabricated by both the RP circuit and the self-bias circuits in an aluminum housing. As a result, the characteristics of the LNA implemented show more than 32 dB in gain, lower than 0.5 dB in noise figure, 18.6 dBm output gain in 1 dB gain compression point.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.281-284
• /
• 2004

In Recent, it became necessary to envelope the technology about electrodeless fluorescent lamp according to demand of the electrodeless fluorescent lamp system that used higher efficiency and advantage of long-lifetime. Especially, in the electrodeless fluorescent lamp which used H-mode, efficiency of lamp is decided from matching parameter of antena and inverter So it is of the utmost importance to design antena and inverter. Therefore, this paper used a transformer principle for efficiency rising of electrodeless fluorescent lamp and interpreted an equivalent circuit, used an impedance analyzer in order to confirm a performance enhancement of lamp along design of antenna, and confirmed parameter characteristic of R, L, C, Z, Phase, Q-factor along a change of magnetic flux density. Also, this paper confirmed a luminance characteristic of electrodeless lamp along parameter change with measuring optical characteristic along a change of magnetic flux density.

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.164-166
• /
• 2004

In Recent, it became necessary to develope the technology about electrodeless fluorescent lamp according to demand of the electodeless fluorescent lamp system that used higher efficiency and advantage of long-lifetime. Especially, in the electordeless fluorescent lamp which used H-mode, efficiency of lamp is decided from matching parameter of antena and inverter, so it is of the utmost importance to design antena and inverter. Therefore, this paper used a transformer principle for an efficiency rising of electrodeless fluorescent lamp and interpreted an equivalent circuit, and confirmed a luminance characteristic by ferrite change of antenna and change of coil turns. Also, this paper used the thermoelectric element which can let you cool ferrite and antenna and confirmed the luminance characteristic along a change of ferrite and an antenna temperature.

• The KIPS Transactions:PartD
• /
• v.9D no.3
• /
• pp.399-408
• /
• 2002

Component technology was proposed and applied to software development to overcome software crisis. Software component is a black box like an integrated circuit in hardware but it can not be utilized without good support specially for helping users understand efficiently. This paper shows that data book format for understanding hardware component can be well applied to representing software component. We selected an approach to understand component by matching the contents of data book with UML and API model technique. Besides, we added the architecture part and the interface which are the most important property of software component to the data book for software components. In order to verify effectiveness of components data book we extended batch descriptor in EJB and performed an experiment providing data book to programmers with components.