• Wind and Structures
• /
• v.28 no.2
• /
• pp.129-140
• /
• 2019

Accurately simulating the wind field of large-scale region, for instant urban areas, the locations of large span bridges, wind farms and so on, is very difficult, due to the complicated terrains or land surfaces. Currently, the regional wind field can be simulated through the combination of observation data and numerical model using observation-nudging in the Weather Research and Forecasting model (WRF). However, the main drawback of original observation-nudging method in WRF is the effects of observation on the surrounding field is fully mathematical express in terms of temporal and spatial, and it ignores the effects of terrain, wind direction and atmospheric circulation, while these are physically unreasonable for the turbulence. For these reasons, a spatial correlation-based observation-nudging method, which can take account the influence of complicated terrain, is proposed in the paper. The validation and comparation results show that proposed method can obtain more reasonable and accurate result than original observation-nudging method. Finally, the discussion of wind field along bridge span obtained from the simulation with spatial correlation-based observation-nudging method was carried out.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.3
• /
• pp.521-529
• /
• 2017

In this study, analyzed the effective width of concrete unfilled composite steel grid deck which has different shear connector details from that of composite bridge. The effective width of concrete unfilled composite steel grid deck according to effective width calculation method, load size and main bearing bar spacing-span ratio was evaluated. As a result of analysis, it is analyzed that the effective width is calculated to be nearly equal to the actual effective width by idealizing the stress shape as a trapezoidal shape. In addition, shear hole penetration reinforcing bars applied to increase the shear strength is shown to increase the effective width. From the results of the analysis of the effective width according to main bearing bar spacing-span ratio, proposes the correction factor that can calculate the effective width ratio of the unfilled steel composite steel grid deck.

• Earthquakes and Structures
• /
• v.1 no.2
• /
• pp.215-230
• /
• 2010

The main objectives of this work were to investigate the effects of the nonlinear behavior of the isolation pads on the seismic response of bridges with rubber bearings, and to identify when base isolation improved their seismic performance. To achieve these objectives a parametric study was conducted designing a set of bridges for three different soil types and varying the number of spans, span lengths, and pier heights. The seismic responses (accelerations, displacements and pier seismic forces) were evaluated for three different structural models subjected to three earthquakes with different dynamic characteristics. The first represented bridges without base isolation; the second corresponded to the same bridges including now rubber bearings as an isolation system, with linear elastic behavior that shifted the natural period of the bridge by a factor of 2 to 4. In the third model the seismic response of bridges supported on lead-Rubber bearings was studied accounting for the nonlinear behavior of the lead. The results show clearly the importance of the nonlinear behavior on the seismic performance of the bridges.

• Proceedings of the KSR Conference
• /
• 2003.10b
• /
• pp.477-482
• /
• 2003

The railway bridges on the new high-speed line are the first structures designed and constructed by our local engineers for high-speed running. In securing running stability and riding comfort in high-speed running, it is very important to verify the performance of structures and local specifications and design criteria by measuring and analyzing the dynamic behavior of main structural members. In this study, 4 different types(simple-span, 2, 3, 4-continuous spans) of PCS Box bridges on the test line(Yongwa$\~$Simok section) were selected, each representing a different type of superstructures, in order to verify the performance of the bridges by measuring dynamic responses during the test-run of KTX. Reviews of the running stability and the riding comfort were carried out with the results of the measurement and the analyses of vibration acceleration, endrotation, distortion and deflection at midspan.

• Journal of the Korean Society of Safety
• /
• v.17 no.3
• /
• pp.102-106
• /
• 2002

The Act on Safety Management of Social Assets was established on 1995 and revised on 1999 to relieve maintenance cost of managing offices. The provision for load bearing test before opening was deleted and the number of load bearing test after opening was reduced in the Revised Act on 1999. The effect of revision is the main concern in this study. 176 technical reports on load bearing test of long span bridges are analyzed. The results show that various structural defects are inherent in recent bridges constructed since 1995. So the preservation of provisions deleted in original act is needed up to now.

• Smart Structures and Systems
• /
• v.22 no.1
• /
• pp.95-103
• /
• 2018

Active vibration control via inertial mass actuators has been shown as an effective tool to significantly reduce human-induced vertical vibrations, allowing structures to satisfy vibration serviceability limits. However, a lot of practical obstacles have to be solved before experimental implementations. This has motivated simple control techniques, such as direct velocity feedback control (DVFC), which is implemented in practice by integrating the signal of an accelerometer with a band-pass filter working as a lossy integrator. This work provides practical guidelines for the tuning of DVFC considering the damping performance, inertial mass actuator limitations, such as stroke and force saturation, as well as the stability margins of the closed-loop system. Experimental results on a full scale steel-concrete composite structure (behaves similar to a footbridge) with adjustable span are reported to illustrate the main conclusions of this work.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.466-471
• /
• 2011

본 연구에서는 장대 현수교 주케이블의 가설시 선형관리를 위한 기초적 연구를 수행하였다. 우선, 포물선 요소 및 탄성현수선 요소의 정식화 과정을 검토하고, 각 요소의 적용에 따른 현수교 주케이블 완성계 및 가설계의 형상, 장력, 무응력장 등을 비교검토 하였다. 또한, 탄성현수선의 적용시 주케이블 가설계의 setback량 산정 방법을 제시하였으며, 이에 따른 산정 결과를 유한요소해석 결과와 비교검토 하였다. 최종적으로, 주케이블 가설계의 중앙경간 새그량 변화에 따른 탑정 새들부에서의 미끌림 안정성에 대한 민감도 해석을 수행할 예정이다.

• Structural Engineering and Mechanics
• /
• v.27 no.4
• /
• pp.477-499
• /
• 2007

The main purpose of this paper is to investigate the ultimate behavior of steel cable-stayed bridges with design variables and compare the validity and applicability of computational methods for evaluating ultimate load capacity of cable-stayed bridges. The methods considered in this paper are elastic buckling analysis, inelastic buckling analysis and nonlinear elasto-plastic analysis. Elastic buckling analysis uses a numerical eigenvalue calculation without considering geometric nonlinearities of cable-stayed bridges and the inelastic material behavior of main components. Inelastic buckling analysis uses an iterative eigenvalue calculation to consider inelastic material behavior, but cannot consider geometric nonlinearities of cable-stayed bridges. The tangent modulus concept with the column strength curve prescribed in AASHTO LRFD is used to consider inelastic buckling behavior. Detailed procedures of inelastic buckling analysis are presented and corresponding computer codes were developed. In contrast, nonlinear elasto-plastic analysis uses an incremental-iterative method and can consider both geometric nonlinearities and inelastic material behavior of a cable-stayed bridge. Proprietary software ABAQUS are used and user-subroutines are newly written to update equivalent modulus of cables to consider geometric nonlinearity due to cable sags at each increment step. Ultimate load capacities with the three analyses are evaluated for numerical models of cable-stayed bridges that have center spans of 600 m, 900 m and 1200 m with different girder depths and live load cases. The results show that inelastic buckling analysis is an effective approximation method, as a simple and fast alternative, to obtain ultimate load capacity of long span cable-stayed bridges, whereas elastic buckling analysis greatly overestimates the overall stability of cable-stayed bridges.

• Wind and Structures
• /
• v.20 no.5
• /
• pp.701-718
• /
• 2015

The joint distribution of wind speed and wind direction at a bridge site is vital to the estimation of the basic wind speed, and hence to the wind-induced vibration analysis of long-span bridges. Instead of the conventional way relying on the weather stations, this study proposed an alternate approach to obtain the original records of wind speed and the corresponding directions based on field measurement supported by the Structural Health Monitoring System (SHMS). Specifically, SHMS of Sutong Cable-stayed Bridge (SCB) is utilized to study the basic wind speed with directional information. Four anemometers are installed in the SHMS of SCB: upstream and downstream of the main deck center, top of the north and south tower respectively. Using the recorded wind data from SHMS, the joint distribution of wind speed and direction is investigated based on statistical methods, and then the basic wind speeds in 10-year and 100-year recurrence intervals at these four key positions are calculated. Analytical results verify the reliability of the recorded wind data from SHMS, and indicate that the joint probability model for the extreme wind speed at SCB site fits well with the Weibull model. It is shown that the calculated basic wind speed is reduced by considering the influence of wind direction. Compared to the design basic wind speed in the Specification of China, basic wind speed considering the influence of direction or not is much smaller, indicating a high safety coefficient in the design of SCB. The results obtained in this study can provide not only references for further wind-resistance research of SCB, but also improve the understanding of the safety coefficient for wind-resistance design of other engineering structures in the similar area.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.5
• /
• pp.43-48
• /
• 2022

In order to evaluate the seismic performance of the modular expansion joint known for its large expansion allowance and remarkable durability, this study conducts seismic response analysis and seismic simulation test. The bridge selected for the seismic response analysis is a cable stayed bridge with main span length of 1,000m. Three artificial earthquake were generated with respect to the design response spectra of the Korean Standards (KS), AASHTO LRFD and Eurocode, and applied to the selected bridge. The seismic simulation tests reproduced the artificial earthquakes using dynamic hydraulic actuators in the longitudinal and transverse directions. The test results verified the durability and safety of the expansion joint in view of its seismic behavior since abnormal behavior or failure of the expansion joint was not observed when the artificial earthquake waves were applied in the longitudinal direction, transverse direction and both directions.