• Journal of Magnetics
• /
• 제6권1호
• /
• pp.31-35
• /
• 2001

This paper describes the design method of a magnetic system to maximize the magnetic flux leakage (MFL) in a non-destructive testing (NDT) system. The defect signals in a MFL type NDT system mainly depend on the change of the magnetic leakage flux in the region of a defect. The characteristics of the B-H curves are analysed and a design method to define the operating point on B-H curves for maximum leakage is performed. The computed MFL signal by a nonlinear finite element method is verified by measurement using Hall sensors mounted on the 6 legs PIG, the traveling detector unit in gas pipe, in an 8 inch test tube with defects. The rhombic defects could be successfully identified from the defect signals.

• 한국압력기기공학회 논문집
• /
• 제6권2호
• /
• pp.47-53
• /
• 2010

In this research project, development of methodology to measure the thickness of pipes in the wide range using magnetic field. The magnetic field spreading in the sensor and the plate was modeled in the cases of the various thicknesses in plate. Based on the analysis, sensors were designed, manufactured and tested to optimize the specifications of the sensor. The sensor can be used in high temperature through calibration. And the uncertainty of the sensor was estimated.

• 대한안전경영과학회지
• /
• 제2권1호
• /
• pp.89-97
• /
• 2000

This paper shows the study for development inprocess measuring magnetic sensor for tolerance control, First, we fabricated and annealed sample amorphous ribbons which were made of ($CO_{0.94}$$Fe_{0.06}$)$_{79}$$Si_{2}$$b_{19}$ having near zero magnetostrictive. It had 12［$\mu\textrm{m}$］ of thickness, 10［mm］ of length, and 2.5［mm］ of width. Then, we measured the magnetic characteristics such as frequency dependency over impedance variation rate and position change over impedance variation. As the results of the evaluation, we found that the sample ribbons had excellent sensor characteristics. Then, we made sensors by using the sample ribbons, As the results of the measurements, it proved that the ribbon could be used as excellent magnetic sensor for which it was possible to control inprocess measurement within the tolerance range(~$\mu\textrm{m}$ ).

• 한국자기공명학회논문지
• /
• 제23권3호
• /
• pp.73-80
• /
• 2019

Nitrogen-vacancy (NV) is one of the most popular solid-state spin systems for quantum sensing. NV has been used for vector magnetometry with nanometer spatial resolution and sensors for nuclear magnetic resonance (NMR) in samples with small volume, less than 10 pL. Various studies are in progress to make NV a complementary sensor for current NMR technique. Fabricating and improving diamond itself are one of the research topics. This mini-review contains recent develops in diamond fabrication and treatment for higher NV yield. Additionally, we briefly introduce the development status of NV in NMR.

• Advances in materials Research
• /
• 제11권4호
• /
• pp.331-349
• /
• 2022

In the present work, we proposed an analytical study on buckling behavior of a sandwich plate with polymeric core integrated with piezo-electro-magnetic layers such as BaTiO3 and CoFe2O4 reinforced by graphene platelets (GPLs). The Halpin-Tsai micromechanics model is used to describe the properties of the polymeric core. The governing equations of equilibrium are obtained from first-order shear deformation theory (FSDT) and the Navier's method is employed to solve the equations. The results show the effect of different parameters such as thickness, length, weight fraction of GPLs, and also effect of electric and magnetic field on critical buckling load. The result of this study can be obtained in the aerospace industry and also in the design of sensors and actuators.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2000년도 International Symposium on Magnetics The 2000 Fall Conference
• /
• pp.539-545
• /
• 2000

This paper describes the design method of the magnetic system to maximize the magnetic flux leakage (MFL) in non-destructive testing (NDT) system. The defect signals in MFL type NDT system mainly depends on the change of the magnetic leakage flux in the region of defect. The characteristics of the B-H curves are analyzed and the design method to define the operating point in B-H curves for the maximum leakage is performed. The computed MFL signal by nonlinear finite element method is verified by measurement using Hall sensors mounted on the 6 legs PIG in the 8 inches test tube with defects. The rhombic defects could be successfully composed from the defect signals.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.213-219
• /
• 2002

A cone-shaped active magnetic healing spindle system for high speed internal grinding with built-in motor that has 7.5kW power and maximum rotational speed of 50,000 rpm is designed and built. Using cone-shaped AMB(Active Magnetic Bearing) system, the axial rotor dick and magnets of conventional 5-axis actuating design can be eliminated. so this concept of design provides a simple magnetic bearing system. In this paper, the cone-shaped electromagnets are designed by magnetic circuit theory, and a de-coupled direct feedback PID controller is applied to control the coupled magnetic bearings. The designed crone-shaped AMB spindle system is built and constructed with a digital control system, which has TMS320C6702 DSP, 16 bit AD/DA, switching power amplifier and gap sensors. As the AMB system provides high damping ratio eliminating overshoot and resonance speed, this spindle runs up to 40,000 rpm stably with about 5${\mu}{\textrm}{m}$ of runout.

• 센서학회지
• /
• 제17권4호
• /
• pp.308-316
• /
• 2008

For the measurement of liquid level in ship's cargo tank, ballast tank, fuel oil tank and fresh water tank, several types of gauge meter are used such as tubular type, magnetic float type, reflex type transparent type and welding pad type. Among them, magnetic float type gauge meter is environmental friendly device because it is free of power source and maintenance. The main obstacle of the device is relatively large error bound. In this paper, finite element method is used to design and analysis of the magnetic float type gauge meter. The operation of reed switch according to the magnetic field has been successfully described and agreed well with experimental measurement. The optimum geometry with combination of permanent magnet and reed switches are designed to achieve 98 % accuracy of fluid level.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2003년도 하계학술연구발표회 및 한.일 공동심포지엄
• /
• pp.150-151
• /
• 2003

In the past years, a giant magnetoresistance (GMR) effect found in perovskite-like structured materials has attracted considerable attention among scientists and manufacturers, since, a practical point of view, the capacity of producing magnetic and sensing sensors. In a stream of this interest, further efforts to understand the underlying mechanism that leads to the GMR effect relative to the correlation between transport and magnetic properties, have been extensively devoted. In these cases, spin-glass-like behaviors are ascribed to the frustration of random competing exchange interactions, namely the ferromagnetic double-exchange interaction between Co$\^$3+/ (or Mn$\^$3+/) and Co$\^$4+/(or Mn$\^$4+/) and the antiferromagnetic one like spins. Noticeably, the distinction of spin-glass region from cluster-glass one, involved in the remarkable changes in transport and magnetic properties at a critical value of doping concentration, was observed. Magnetic anomalies in zero-field-cooled (ZFC) magnetization as well as ac magnetic susceptibility below Curie temperature T$\sub$c/ and the charge/orbital fluctuation were also realized. In this work, we present a study of magnetic properties of a deficient manganese perovskites system of La$\sub$0.6/Sr$\sub$x/MnTi$\sub$y/O$_3$, and particularly provide its new magnetic phase diagram.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 춘계학술대회 논문집
• /
• pp.7-8
• /
• 2009

Non-contact critical current measurement apparatus was developed using hall probe which measures the magnetic field distribution across the width of superconducting tape. The hall probe consists of 7 independent hall sensors which lie in a line 600 ${\mu}m$. The difference between maximum and minimum magnetic field in the magnetic filed distribution is a main parameter to determine the critical current. As preliminary research, we calculated the magnetic field intensity at the middle sensor, which is a minimum magnetic field and generated by the circular shielding current modeled by Bean model. We confirmed that there are some parameters that affect on the minimum magnetic field; the distance between superconducting layer and hall sensor, the width of superconducting tape, and the critical current distribution across the width of superconducting tape. Among these parameters, the distance between superconducting layer and hall sensor highly influences on the minimum magnetic field.