• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.186-186
• /
• 2000

After LeComber et al. reported the first amorphous hydrogenated silicon (a-Si: H) TFT, many laboratories started the development of an active matrix LCDs using a-Si:H TFTs formed on glass substrate. With increasing the display area and pixel density of TFT-LCD, however, high mobility TFTs are required for pixel driver of TF-LCD in order to shorten the charging time of the pixel electrodes. The most important of these drawbacks is a-Si's electron mobiliy, which is the speed at which electrons can move through each transistor. The problem of low carier mobility for the a-Si:H TFTs can be overcome by introducing polycrystalline silicon (poly-Si) thin film instead of a-Si:H as a semiconductor layer of TFTs. Therefore, poly-Si has gained increasing interest and has been investigated by many researchers. Recnetly, fabrication of such poly-Si TFT-LCD panels with VGA pixel size and monolithic drivers has been reported, . Especially, fabricating poly-Si TFTs at a temperature mach lower than the strain point of glass is needed in order to have high mobility TFTs on large-size glass substrate, and the monolithic drivers will reduce the cost of TFT-LCDs. The conventional methods to fabricate poly-Si films are low pressure chemical vapor deposition (LPCVD0 as well as solid phase crystallization (SPC), pulsed rapid thermal annealing(PRTA), and eximer laser annealing (ELA). However, these methods have some disadvantages such as high deposition temperature over $600^{\circ}C$, small grain size (<50nm), poor crystallinity, and high grain boundary states. Therefore the low temperature and large area processes using a cheap glass substrate are impossible because of high temperature process. In this study, therefore, we have deposited poly-Si thin films on si(100) and glass substrates at growth temperature of below 40$0^{\circ}C$ using newly developed high rate magnetron sputtering method. To improve the sputtering yield and the growth rate, a high power (10~30 W/cm2) sputtering source with unbalanced magnetron and Si ion extraction grid was designed and constructed based on the results of computer simulation. The maximum deposition rate could be reached to be 0.35$\mu$m/min due to a high ion bombardment. This is 5 times higher than that of conventional sputtering method, and the sputtering yield was also increased up to 80%. The best film was obtained on Si(100) using Si ion extraction grid under 9.0$\times$10-3Torr of working pressure and 11 W/cm2 of the target power density. The electron mobility of the poly-si film grown on Si(100) at 40$0^{\circ}C$ with ion extraction grid shows 96 cm2/V sec. During sputtering, moreover, the characteristics of si source were also analyzed with in situ Langmuir probe method and optical emission spectroscopy.

• Korean Journal of Acupuncture
• /
• v.29 no.1
• /
• pp.83-92
• /
• 2012

Objectives : The purpose of this research was to develop the magnetic acupuncture system which used solenoid coil for magnetizing acupuncture needle. The system could generate the meridian electric potential (MEP) similar to the potential by manual acupuncture. Thus, we tried to confirm the therapeutic effect that is caused by the MEP generation. Methods : To confirm the MEP, we stimulated the magnetic acupuncture with at 2Hz, $92.7{\pm}2mT$, PEMFs (Pulsed Electro-Magnetic Fields) at ST37 and measured the evoked potential between ST36 and ST41. Also, we conducted a fatigue recovery test using isokinetic exercise in order to identify the therapeutic effect on musculoskeletal disorders. We chose LR9 as a stimulation point. To observe the state of fatigue, we measured the EMG and analyzed median frequency and peak torque for 20minutes. Results : We observed that MEP which incurred from magnetic acupuncture was higher than he reported MEP induced by manual acupuncture. Moreover, its modes were divided into two types by the direction of magnetic flux. When generating magnetic flux in the direction of acupoint, the positive peak voltage of the MEP was generated. In contrast, negative peak voltage of the MEP was generated whenever meganetic flux generated in the outward direction. As a result of fatigue recovery, the median frequency (MF) of the magnetic acupuncture group were recovered faster than that of the non-stimulation group. However, the peak torques of both groups were not restored until after 20 minutes. Conclusions : We confirmed that the magnetic acupuncture system can lead to the MEP similar to manual acupuncture. Moreover, the MEP had a therapeutic effect on the musculoskeletal disorders.

• Restorative Dentistry and Endodontics
• /
• v.23 no.1
• /
• pp.366-378
• /
• 1998

Thermocondensation root canal filling technique have been used to fill accessary canals or to obtain homogeneous root caral fillings. But these thermocondensation technique inevitably produce heat in the canal which can be transmitted through the dentin and cementum and consequently damage periodontal ligamental cells and osteoblasts. In this study, System $B^{TM}$(Analytic technology, WA.D.S.A.) was used to evaluate the reaction of periodontal ligament tissue to "Continous Wave condensation technique" introduced by Buchanan, and the transmitted root surface temperature was measured according to measured root thicknesses. 12 Mandibular incisors of two adult dogs were used for the experiment. 6 controls were filled by lateral condensation technique with sealer.3 specimens were apically filled by Continuous Wave technique at $200^{\circ}C$ for 5 seconds and remaining 3 specimens were additionally backfilled using System $B^{TM}$(Analytic technology, WA.D.S.A.) was used to evaluate the reaction of periodontal ligament tissue to "Continous Wave condensation technique" introduced by Buchanan, and the transmitted root surface temperature was measured according to measured root thicknesses. 12 Mandibular incisors of two adult dogs were used for the experiment. 6 controls were filled by lateral condensation technique with sealer.3 specimens were apically filled by Continuous Wave technique at $200^{\circ}C$ for 5 seconds and remaining 3 specimens were additionally backfilled using System $B^{TM}$ at $100^{\circ}C$ for 20 seconds. Six weeks later, the dogs were sacrificed and the teeth stained with Hematoxylin and Eosin for histologic examination. 6 extracted human teeth were used to measure the transmitted temperature. After cutting off the crown, the canals were prepared and divided into 3 groups with root thickness of 1.5mm, 1.0mm, 0.5mm, 2 teeth in each group. Inside each root canal, System $B^{TM}$ was heated as with the temperature for the apically condensed and the back filled group, and the transmitted heat was measured on the external surface of the root. The temperature of System $B^{TM}$ heat spreader at $200^{\circ}C$ and $100^{\circ}C$ was also measured at root temperature. It can be concluded as follows: 1. In the thin area (200-$250{\mu}m$) of the root, root resorption could be seen even with heating at $200^{\circ}C$ for 5 seconds. 2. When the spreader was heated at $200^{\circ}C$ for 5 seconds and additionally at $100^{\circ}C$ for 20 seconds for backfill, all teeth showed root resorption regardless of their root thickness. 3. The transmitted external root surface temperature was higher as the root thickness decreased and as the heating time increased. In the thermocompaction technique using System $B^{TM}$, the spreader should be heated for the minimal time and used only in the apical area. The heated spreader shouldn't inserted to the binding point of the canal and backfilling should be done with other means of minimally heated gutta percha technique.

• Journal of Distribution Science
• /
• v.13 no.1
• /
• pp.35-46
• /
• 2015

Purpose - This paper attempted to investigate the relationships among the perception of job insecurity and organizational effectiveness, and it examines these relationships while considering the moderating effect of trust in the manager and self-efficacy. Job insecurity is an independent variable, organizational effectiveness aspects (job satisfaction, organizational commitment, and turnover intention) are dependent variables, and trust and self-efficacy are moderators. Research design, data, and methodology - Regression analysis was used to verify the effects. The measurement items were already deemed as reliable and valid in the previous study, but for this purpose, some modifications were made. To examine the model, this study relied on the samples chosen from Korean employees in the six franchise business firms. The survey was conducted on 288 workers. Each question is based on a 5-point Likert type scale. The data were analyzed using SPSS 18.0. Results - The results of the study are summarized as follows. First, job insecurity has an influence on organizational effectiveness aspects (negatively on job satisfaction, negatively on organizational commitment, and positively on turnover intention). Second, analyzing the moderating effect of trust, trust in manager is mediated between job insecurity and organizational effectiveness aspects (on organizational commitment and on turnover intention). However, employees' trust in manager had no significant moderating effect on the job insecurity-job satisfaction relationship. Third, self-efficacy is mediated between job insecurity and organizational effectiveness aspects (on job satisfaction, on organizational commitment, and on turnover intention). Conclusions - First, it is necessary to be aware of the seriousness of employees' job insecurity in franchise firms, which have played a pivotal role in national economic growth, and to create a detailed plan for reducing insecurity and actively implementing it. To this end, the franchise companies should implement efficiency efforts such as obtaining an appropriate capacity of equipped personnel and a training program. Second, there are moderating effects of self-efficacy and trust in the relationship between job insecurity and organizational effectiveness. Depending on business conditions, stability and instability can only be experienced in the organizations of franchise companies. This can give rise to instability in employment. Therefore, it is necessary to develop and utilize a system that can be minimized with a change in the new awareness of employment instability. After all, a good leader (manager) must accumulate personal trust and build up a core competence that is necessary to become competent in the field himself. Even if you lack the material resources to improve performance, if the leader with the core competencies (e.g., technical/management /organization/marketing/design) can gain the trust of the supervisor, you can get a good organizational performance. Therefore, you should foster a healthy organizational culture through education such as leadership training and employee training to be built on trust between the leaders and the employees. In addition, you need to focus on HRD&M training in order to increase the self-efficacy of the supervisor.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.45 no.3
• /
• pp.342-351
• /
• 2016

This study was carried out to develop an optimized analytical method using high-performance liquid chromatography (HPLC) applied to canthaxanthin, which is not yet designated as a food colorant in Korea, as well as to perform validation and uncertainty evaluation of this method. Official methods of AOAC, UK, and Japan with HPLC-UV detection were evaluated for the analysis of canthaxanthin by comparison of linearity, resolution, selectivity, limit of detection (LOD), limit of quantitation (LOQ), accuracy, precision, recovery, inter-laboratory tests, and uncertainty measurement. The calibration curves showed high linearity with an $R_2$ value of over 0.999 for canthaxanthin standard solutions in all three official methods. The official method of Japan exhibited the best results in terms of resolution and selectivity, including the lowest LOD and LOQ. The average coefficients of variation were calculated as less than five of three institutes with a precision value less than 1, accuracy near 100%, and recovery ratio between $100{\pm}10%$. The expanded uncertainty for canthaxanthin was estimated to be $39.5{\pm}5.29mg/kg$ (95% confidence level, k=2), and the uncertainty of measurement was 13.4%. In this study, official methods of canthaxanthin were compared and the validities verified. The results will be further applied to establish an authorized analytical method for canthaxanthin in Korea.

• Gut and Liver
• /
• v.12 no.6
• /
• pp.728-735
• /
• 2018

Background/Aims: The combination of nab-paclitaxel and gemcitabine (nab-P/Gem) is widely used for treating metastatic pancreatic cancer (MPC). We aimed to evaluate the therapeutic outcomes and prognostic role of treatment-related peripheral neuropathy in patients with MPC treated with nab-P/Gem in clinical practice. Methods: MPC patients treated with nab-P/Gem as the first-line chemotherapy were included. All 88 Korean patients underwent at least two cycles of nab-P/Gem combination chemotherapy (125 and $1,000mg/m^2$, respectively). Treatment-related adverse events were monitored through periodic follow-ups. Overall survival and progression-free survival were estimated by the Kaplan-Meier method, and the Cox proportional hazards regression linear model was applied to assess prognostic factors. To evaluate the prognostic value of treatment-related peripheral neuropathy, the landmark point analysis was used. Results: Patients underwent a mean of $6.7{\pm}4.2$ cycles during $6.3{\pm}4.4$ months. The median overall survival and progression-free survival rates were 14.2 months (95% confidence interval [CI], 11.8 to 20.3 months) and 8.4 months (95% CI, 7.1 to 13.2 months), respectively. The disease control rate was 84.1%; a partial response and stable disease were achieved in 30 (34.1%) and 44 (50.0%) patients, respectively. Treatment-related peripheral neuropathy developed in 52 patients (59.1%), and 13 (14.8%) and 16 (18.2%) patients experienced grades 2 and 3 neuropathy, respectively. In the landmark model, at 6 months, treatment-related peripheral neuropathy did not have a significant correlation with survival (p=0.089). Conclusions: Nab-P/Gem is a reasonable choice for treating MPC, as it shows a considerable disease control rate while the treatment-related peripheral neuropathy was tolerable. The prognostic role of treatment-related neuropathy was limited.

• Korea Real Estate Review
• /
• v.24 no.1
• /
• pp.27-37
• /
• 2014

Recently increasing the supply of housing policy has not been able to reflect social phenomena as like decreasing birth rate, aging of the population and increasing 1 or 2 person households. This study analyze the housing demand in the city with the point of population growth rate and economic character changes. Growing cities have positive population growth rate and economic character, but shrinking cities have the opposite. By comparing housing demand of growing cities and shrinking cities, we want to find out housing policy implications. In this study, results suggest that the peak age of housing demand of shrinking cities is the late 60's. But the growing cities's age peak is the mid-80's. But further analysis of the economic variables and 1 or 2 person old and young household dummies, the result is that the peak age of housing demand is reduced. These results suggest that housing demand should be differentiated the cities's population structure and economic characteristics of the household. In short, housing demand will vary depending on the condition of individual cities.

• Journal of Climate Change Research
• /
• v.6 no.4
• /
• pp.357-366
• /
• 2015

This study was conducted to estimate carbon stocks of Quercus serrata with drawing volume of trees in each tree height and DBH applying the suitable stem taper equation and tree specific carbon emission factors, using collected growth data from all over the country. Information on distribution area, tree number per hectare, tree volume and volume stocks were obtained from the $5^{th}$ National Forest Inventory (2006~2010), and method provided in IPCC GPG was applied to estimate carbon storage and removals. Performance in predicting stem diameter at a specific point along a stem in Quercus serrata by applying Kozak's model,$d=a_1DBH^{a_2}a_3^{DBH}X^{b_1Z^2+b_2ln(Z+0.001)+b_3{\sqrt{Z}}+b_4e^Z+b_5({\frac{DBH}{H}})}$, which is well known equation in stem taper estimation, was evaluated with validations statistics, Fitness Index, Bias and Standard Error of Bias. Consequently, Kozak's model turned out to be suitable in all validations statistics. Stem volume tables of Quercus serrata were derived by applying Kozak's model and carbon stock tables in each tree height and DBH were developed with country-specific carbon emission factors ($WD=0.65t/m^3$, BEF=1.55, R=0.43) of Quercus serrata. As a result of carbon stock analysis by age class in Quercus serrata, carbon stocks of IV age class (11,358 ha, 36.5%) and V age class (10,432; 33.5%) which take up the largest area in distribution of age class were 957,000 tC and 1,312,000 tC. Total carbon stocks of Quercus serrata were 3,191,000 tC which is 3% compared with total percentage of broad-leaved forest and carbon sequestration per hectare(ha) was 3.8 tC/ha/yr, $13.9tCO_2/ha/yr$, respectively.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.233-233
• /
• 2015

Vu Gia - Thu Bon basin is located in central Vietnam between Truong Son mountain range on the border with Lao in the west and the East Sea in the east. The basin occupies about 10,350 km2 or roughly 90% of the Quang Nam Province and includes Da Nang, a very large city with about 876,000 inhabitants. Total annual rainfall ranges from about 2,000 mm in central and downstream areas to more than 4,000 mm in southern mountainous areas. Rainfall during the monsoon season accounts for 65 to 80% of total annual rainfall. The highest amount of rainfall occurs in October and November which accounts for 40 to 50% of the annual rainfall. Rainfall in the dry season represents about 20 to 35% of the total annual rainfall. The low rainfall season usually occurs from February to April, accounting for only 3 to 5% of the total annual rainfall. The mean annual flow volume in the basin is $19.1{\times}109m 3$. Similar to the distribution of rainfall, annual flows are distinguished by two distinct seasons (the flood season and the low-flow season). The flood season commonly starts in the mid-September and ends in early January. Flows during the flood season account for 62 to 69% of the total annual water volume, while flows in the dry season comprise 22 to 38% of total annual run-off. The water volume gauged in November, the highest flow month, accounts for 26 to 31% of the total annual run-off while the driest period is April with flows of 2 to 3% of the total annual run-off. There are some hydropower projects in the Vu Gia - Thu Bon basin as the cascade of Song Bung 2, Song Bung 4, and Song Bung 5, the A Vuong project currently under construction, the Dak Mi 1 and Dak Mi 4 projects on the Khai tributary, and the Song Con project on the Con River. Both the Khai tributary and the Song Con join the Bung River downstream of SB5, although the Dak Mi 4 project involves an inter-basin diversion to Thu Bon. Much attention has recently been focused on the effects that climate variability and human activities have had on runoff. In this study, data from the Vu Gia - Thu Bon River Basin in the central of Viet Nam were analyzed to investigate changes in annual runoff during the period of 1977-2010. The nonparametric Mann-Kendall test and the Mann-Kendall-Sneyers test were used to identify trend and step change point in the annual runoff. It was found that the basin had a significant increasing trend in annual runoff. The hydrologic sensitivity analysis method was employed to evaluate the effects of climate variability and human activities on mean annual runoff for the human-induced period based on precipitation and potential evapotranspiration. This study quantitatively distinguishes the effects between climate variability and human activities on runoff, which can do duty for a reference for regional water resources assessment and management.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.30-30
• /
• 2015

유역에 내린 강우의 총량은 홍수나 갈수 측면에서 매우 중요하다. 점 강우량에 의해 측정된 강우량을 이용하여 유역 총강우량으로 환산하는 과정에 많은 오차가 포함되어 있다. 선행연구에 따르면, 우량계를 통한 강우관측에서 언더캐치(undercatch)에 의한 계통오차는 일반적으로 5~16%, 우연오차는 약 5%가 발생된다고 보고하였으며, 점 우량계 자료를 내삽하여 공간자료로 변환할 경우 0.1km 규모에서 표준오차가 4~14%, 1km 규모에서는 33~45%, 10km 규모에서는 약 65% 정도 발생된다고 한다. 이러한 우량계 관측오차 및 강우자료 처리과정에서 발생되는 오차는 유역의 유출량 계산에 영향을 주어 홍수예보 정확도를 크게 떨어뜨릴 수 있다. 우리나라에서는 지금까지 유역 총강우량 산정 측면에서 지점강우량의 불확실성에 대한 연구가 많이 이루어지지 못하였다. 본 연구에서는 우리나라에서 주로 사용되고 있는 전도형 우량계를 이용하여 소규모 구역에서 관측되는 강우관측의 불확실성을 분석하고자 하였다. 연구에 사용된 우량계는 0.5mm 급 표준 전도형 우량계로 정밀도는 시간당 1~100mm 기준으로 ${\pm}1%$를 기록하여 기상검정규격인 ${\pm}3%$를 만족하고 있다. 이 우량계는 한국건설기술연구원 안동하천실험센터 내에 장애물이 없는 평지에 60m 간격으로 총 6대($2{\times}3$)를 설치하여 2014년 7월 11일부터 9월 2일까지 54일간 관측을 수행하였다. 관측기간 동안 2대의 우량계가 수일동안 강우가 기록되지 않아서 분석에서 제외하였다. 우량계 상호 간의 누적강우량(54일간)을 비교한 결과 2.5~25.5mm의 차이를 나타냈다. 강우강도별 강우량 합계를 비교한 결과 시간당 1mm 이상에서는 약 1%의 차이가 났으며, 시간당 15mm 이상에서는 7.4%의 차이를 나타내어 강도가 큰 강우사상에서 우량계 간의 관측오차가 더 크게 나타났다. 또한 우량계 상호 간의 상관계수를 분석한 결과, 우량계 간의 거리가 가까울수록 그리고 누적시간이 길수록 상관계수는 커지는 것을 확인할 수 있었다. 도출된 결과를 토대로 하면 앞서 언급한 바와 같이 점 우량계 자료를 내삽하거나 유역 또는 계산격자의 대푯값으로 사용하여 1시간 이하 단위로 유출모의를 할 경우 심각한 오차를 발생시킬 수 있음을 시사한다. 보다 신뢰성 있는 홍수예보와 효율적인 유역관리를 위해서는 점 중심의 강우 관측이 아닌 면적 우량에 대한 관측이 이루어져야 하며 이를 위한 기술의 개발이 필요하다.