• Journal of Electrical Engineering and Technology
• /
• v.5 no.2
• /
• pp.290-298
• /
• 2010

This paper proposes an adaptive carrier-based pulse width modulation (PWM) method for a four-switch three-phase (4S3P) inverter under dc-link voltage ripple conditions. The proposed method guarantees balanced output currents despite of the existence of the voltage oscillations across two dc-link capacitors. And also, this new approach achieves a linear over-modulation with calculation time reduction. Simulation and experimental results are given to validate the feasibility of the proposed method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2147-2150
• /
• 2003

Recently, many technologies of the P.L.C (Power Line Carrier) are introduced for an efficient communication. P.L.C communication sends information in the carrier signals by conduction over the power wire. An arc detector is proposed in this paper for the effective transmission. The Power Line Carrier has an advantage in low cost because it uses existent power line. It can be easily applied anywhere that a power line socket is available. But the P.L.C. is very noisy, because many electronic devices in generate electronic noise in modulated signals. This problem should be considered carefully in the design of the arc detector system using P.L.C in railway. The proposed system can be applied for monitoring the arc detector system and the arc locator system in railway. Hence the system will be able to exchange the arc information to be T.C.M.S. (Train Control Management System), bogies and even between a station and trains in railway and use to suspicion fire in train.

• Current Optics and Photonics
• /
• v.5 no.3
• /
• pp.289-297
• /
• 2021

We describe a comb-mode resolving spectroscopic technique by direct time-domain phase correction of unstable interferograms obtained from loosely locked two femtosecond lasers. A low-cost continuous wave laser and conventional repetition rate stabilization method were exploited for locking carrier and envelope phase of interferograms, respectively. We intentionally set the servo control at low bandwidth, resulting in severe interferograms' fluctuation to demonstrate the capability of the proposed correction method. The envelope phase of each interferogram was estimated by a quadratic fit of carrier peaks to correct timing fluctuation of interferograms in the time domain. After envelope phase correction on individual interferograms, we successfully demonstrated 1 Hz linewidth of RF comb-mode over 200 GHz optical spectral-bandwidth with 10-times signal-to-noise ratio (SNR) enhancement compared to the spectrum without correction. Besides, the group delay difference between two femtosecond pulses is successfully estimated through a linear slope of phase information.

• Journal of Positioning, Navigation, and Timing
• /
• v.6 no.4
• /
• pp.181-194
• /
• 2017

In recent years, research has been actively conducted on the navigation in an indoor environment where Global Navigation Satellite System signals are unavailable. Among them, a study performed indoor navigation by integrating pseudolite carrier and Inertial Measurement Unit (IMU) sensor. However, in this case, there was no solution for the cycle slip occurring in the carrier. In another study, cycle slip detection and compensation were performed by integrating Global Positioning System (GPS) and IMU in an outdoor environment. However, in an indoor environment, cycle slip occurs more easily and frequently, and thus the occurrence of half cycle slip also increases. Accordingly, cycle slip detection based on 1 cycle unit has limitations. Therefore, in the present study, the aforementioned problems were resolved by performing indoor navigation through the integration of pseudolite and ultra-low-cost IMU embedded in a smartphone and by performing half cycle slip detection and compensation based on this. In addition, it was verified through the actual implementation of real-time navigation.

• Journal of Astronomy and Space Sciences
• /
• v.21 no.2
• /
• pp.129-140
• /
• 2004

KAO(Korea Astronomy Observatory) GPS group has developed an iRTK system as a near-real time positioning system using GPS carrier phase data. We focused on improving the accuracy of positioning through the updated capability of data processing of KAO's iRTK system using low-cost L1 carrier phase receiver. The accuracy of a positioning was demonstrated by Extended Kalman filter. Experiments were accomplished using from 30m to 20km baselines. Within 10km, the positioning accuracy was improved by approximately 50-70% to the previous study using one minute observable data. However, it took two minutes to obtain 1m level positioning accuracy at 20km point. We expect that the developed iRTK system can be applied to the various fields of GPS in near-real time positioning.

• Elastomers and Composites
• /
• v.58 no.1
• /
• pp.44-56
• /
• 2023

Additive manufacturing (AM) or three-dimensional (3D) printing of metals has been drawing significant attention due to its reliability, usefulness, and low cost with rapid prototyping. Among the various AM technologies, fused deposition modeling (FDM) or fused filament fabrication is receiving much interest because of its simple manufacturing processing, low material waste, and cost-effective equipment. FDM technology uses metal-filled polymer filaments for 3D printing, followed by debinding and sintering to fabricate complex metal parts. An efficient binder is essential for producing polymer filaments and the thermal post-processing of printed objects. This study involved an in-depth investigation of and a fabrication route for a novel multi-component binder system with steel alloy powder (45 vol.%) ranging from filament fabrication and 3D printing to debinding and sintering. The binder system consisted of polyvinyl pyrrolidone (PVP) as a binder and thermoplastic polyurethane (TPU) and polylactic acid (PLA) as a carrier. The PVP binder held the metal components tightly by maintaining their stoichiometry, and the TPU and PLA in the ratio of 9:1 provided flexibility, stiffness, and strength to the filament for 3D printing. The efficacy of the binder system was examined by fabricating 3D-printed cubic structures. The results revealed that the thermal debinding and sintering processes effectively removed the binder/carrier from the cubic structures, resulting in isotropic shrinkage of approximately 15.8% in all directions. The scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) patterns displayed the microstructure behavior, phase transition, and elemental composition of the 3D cubic structure.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.11
• /
• pp.967-976
• /
• 2016

This paper presents a 3D carrier-smoothed GNSS/DR (Global Navigation Satellite System/Dead Reckoning) integrated system for precise ground-vehicle trajectory estimation. For precise DR navigation on sloping roads, the AHRS (Attitude Heading Reference System) methodology is employed. By combining the integrated carrier phase of GNSS and DR sensor measurements, a vehicle trajectory with an accuracy of less than 20cm is obtained even when cycle slip or change of visibility occur. In order to supplement the weak GNSS environment with DR successfully, the DR sensor is precisely compensated for using GNSS Doppler measurements when GNSS visibility is good. By integrating a multi-GNSS receiver with low-cost IMU, a precise 3D navigation system for land vehicles is proposed in this paper. For real-time implementation, a decoupled Kalman filter is employed in the integrated system. Through field experiments, the performance of the proposed system is verified in various road environments, including sloping roads, good-visibility areas, high multi-path areas, and under-ground parking areas.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.25 no.4
• /
• pp.111-123
• /
• 2017

This study aimed at finding the ways to improve competitiveness of Korean low cost carriers in the highly competitive air transport market by understanding the relation among the influence of prior knowledge, service quality on customer satisfaction and reuse intention. The result of the research is as the following. At first, the influence of prior knowledge on customer satisfaction and reuse intention was statistically significant. The result indicates that customers who have much prior knowledge are more likely to be satisfied and to reuse. Secondly, the test for finding out the influence of service quality on customer satisfaction and reuse intention was statistically significant also. Thirdly, the results revealed that customer satisfaction positively influenced reuse intension. The influence of service quality on customer satisfaction and reuse intention reached the same research result compared with the existing literature.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.111-113
• /
• 2009

This paper shows that you can achieve high quality N+ emitter layers using a screen printable phosphorous diffusion paste and firing in an infrared belt furnace. Spreading resistance measurement from a beveled sample is used to measure carrier concentration as a function of depth for different phosphorous concentrations. Contours of estimated sheet resistance are shown for different processing conditions. This paper describes newly developed low cost phosphorous pastes. It shows the characterization of the newly developed phosphorous paste (DP99-038). This low cost pastes can easily be printed and make 16% efficiency.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.141.5-141
• /
• 2001

An attitude GPS receiver with 3 antennas obtains 3-dimensional attitude using GPS carrier phase measurement INS obtains the 3 dimensional navigation solution for IMU consisting of accelerometers and gyro. Ground-alignment process for the low -cost INS cannot be performed well due to the large sensor noise. Using the standard GPS receiver, however, continuous in-flight alignment for the INS becomes possible, and consequently, the errors in IMU sensors and navigation solution can be compensated. Especially with attitude measurement from the attitude GPS receiver, the compensation of errors in gyroscope and attitude would be done respite of the vehicle´s dynamics and their error covariance would be reduced. This paper presents ...