• Journal of the Korean Society of Safety
• /
• v.27 no.1
• /
• pp.49-54
• /
• 2012

The objective of this study is to investigate the capacity of epoxy injection method using low pressure mixed with high pressure. Injection depth test and flexural strength test were respectively performed on $40{\times}45{\times}35$ cm and $100{\times}10{\times}40$ cm specimens. Considered as the test variables were injection type(low pressure, low and high pressure), crack width(0.25 mm, 0.50 mm), injection direction(upper, lower, side), and epoxy viscosity(low, medium, high). Test results showed that low viscosity epoxy injection depth of injector using low pressure mixed with high pressure for upper direction were 23 cm and tension strength of crack face repaired by injector using low pressure mixed with high pressure was larger than that of concrete.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.1
• /
• pp.55-63
• /
• 2012

This paper presents materials and processing technique to manufacture low viscous strain-hardening cementitious composite which is suitable for structures requiring low viscosity of materials. The micromechanics and fracture mechanics tools coupled with processing techniques were adopted to achieve low viscosity of composites as well as high tensile strain capacity. Optimal volume and length of fibers and interfacial properties between fibers and matrix for composites with tensile strength of 2~3MPa were determined on the basis of the micromechanical analysis and the steady-state cracking theory. Then six mixtures were determined and the experiment was carried out to evaluate the viscosity and uniaxial tensile performance of those. From the test results, it is verified that the strain-hardening cementitious composite with low viscosity suitable for grouting applications in fresh state as well as high ductility over 1.5% in hardened state can be feasible.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.42 no.2
• /
• pp.127-133
• /
• 2016

In this study, water-in-oil (W/O) nanoemulsions of water/Span 80-Nikkol BL 25/oil system were prepared by the PIC method at elevated temperature. This method allows the formation of finely dispersed W/O nanoemulsions with low viscosity in this system. However, macroemulsions rather than nanoemulsions were prepared by PIC method at room temperature. As a result of the significant change of interfacial tension with temperature, the emulsion droplet size decreases from $2{\mu}m$ to 100 nm with the increase in temperature from $30^{\circ}C$ to $80^{\circ}C$. The droplet size of nanoemulsions prepared at $80^{\circ}C$ was in the range of 50 ~ 200 nm and the internal phase content could reach as high as 15 wt%. The most stable nanoemulsion was formed in the vicinity of 7.0 of optimum HLB of the emulsifier mixture. The obtained nanoemulsions were stable without obvious change in droplet size in one month. This study provides valuable information for optimizing the formation of W/O nanoemulsions with low viscosity. These results suggest that W/O nanoemulsions of low viscosity could be useful for cosmetics with soft feeling.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.82-86
• /
• 1996

This study was performed to elucidate the effect of degree of substitution and degree of polymerization of CMC on the rheological characteristics of coating color which is consisted of calcium carbonate as pigment. The results were as follows: 1. It appeared that DP of CMC rather DS has an effect on the low shear viscosity of coating color. 2. According as shear rate increased, the effect of DP and DS on high shear viscosity of coating color decreased. 3. According to increasing DS and DP, the water retention of coating color increased.

• Journal of ILASS-Korea
• /
• v.28 no.2
• /
• pp.68-74
• /
• 2023

In this study, the thickness of the liquid sheet formed by a low speed impinging jet onto a wall was measured by the direct contact method. The spatial distribution characteristics of the sheet thickness in the radial and circumferential directions, and the effects of jet velocity and liquid viscosity were analyzed. The measurement results were compared with the theoretical predictions for two impinging jets. The wavy surface was observed for low viscosity water, but not for high viscosity glycerol solutions. The sheet thickness decreased as the circumferential angle or the distance from the impinging point increased. The sheet thickness increased as the liquid viscosity increased. Comparison with the theoretical predictions showed some differences from the measurement results.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.542-548
• /
• 2012

The viscosity of a ceramic slurry depends on the slurry concentration, particle shape and size, hydrodynamic interactions, temperature, shear rate, pre-treatment condition and the method of measurement with the selected equipment. Representative ceramic slurries with low to high viscosity levels are selected from colloidal silica, barium titanate slurry and glass frit paste. Rotational rheometers and vibrational viscometers are used to compare the measured viscosity for various ceramic slurries. The rotational rheometer measured the viscosity according to the change of the shear rate or the rotational speed. On the other hand, the vibrational viscometer measured one point of the viscosity in a fixed vibrational mode. The rotational rheometer allows the measurement of the viscosity of a ceramic paste with a viscosity higher than 100,000 cP, while the vibrational viscometer provides an easy and quick method to measure the viscosity without deformation of the ceramic slurry due to the measurement method. It is necessary to select suitable equipment with which to measure the viscosity depending on the purpose of the measurement.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.03a
• /
• pp.539-542
• /
• 1999

In this study, acrylate salt material of new chemical composition for injection grouting was prepared in the state of aqueous solution, and the chemical and physical properties of the material were investigated. The gelation time of the material was freely controllable through the control of added catalysts amount. As the viscosity of the material was very low (2∼3cps), its injection efficiency was expected to be very excellent. The variation of its viscosity plotted with the process of gelation revealed that the efficiency of its penetration into the ground soil was very excellent. The LD$\sub$50/ test on white mouse verified the toxicity of the material was very slight and substantially negligible. The grouting effect using the material was examined through field case histories.

• Electrical & Electronic Materials
• /
• v.10 no.9
• /
• pp.945-951
• /
• 1997

Inorder to investigated electrical conduction characteristics of silicone oils due to viscosity variation we studied the electrical conduction properties at temperature range of 10~110[$^{\circ}C$] and electrical field from 1 to 1.33$\times$10$^4$[V/cm] The viscosity of used specimens was low viscous(1, 2, 5[cSt]) silicone oils. It was shown the ohmic conduction characteristics in low temperature and low field by Ion dipole and humidity included specimen. And we known the conduction mechanism due to electron injection by Schottky's effect in the high temperature an d high field region.

• Journal of ILASS-Korea
• /
• v.26 no.1
• /
• pp.26-32
• /
• 2021

In this study, the thickness of the liquid sheet formed by two low speed impinging jets was measured by the direct contact method. The effects of jet velocity and liquid viscosity on the thickness were analyzed and the results were compared with theoretical modeling and optical thickness measurement results. The liquid film thickness decreased as the radius and circumferential angle increased. The jet velocity did not affect the liquid film thickness as predicted in theoretical modeling. In the theoretical modeling, there was no influence of the fluid properties on thickness, but in the case of low viscosity liquids, the thickness was predicted high, and it was well matched in high viscosity liquids. The direct measurement results showed no significant difference from the optical measurement results, thus confirming the reliability of the optical measurement method.

• Macromolecular Research
• /
• v.17 no.5
• /
• pp.289-295
• /
• 2009

Low viscosity aromatic hyperbranched polyester epoxy resin (HTBE) was synthesized by the reaction between epichlorohydrin (ECH) and carboxyl-end hyperbranched polyester (HTB) which was prepared from inexpensive materials $A_2$ (1,4-butanediol glycol, BEG) and $B_3$ (trimellitic anhydride, TMA) by pseudo one-step method. The molar mass of the HTB was calculated from its acid value by "Recursive Probability Approach". The degree of branching (DB) of the HTB was characterized by model compounds and $^1H$ NMR-minus spectrum technology, and the DB of the HTB was about $0.47{\sim}0.63$. The viscosity and epoxy equivalent weight of the HTBE were $3,600{\sim}5,000\;cp$ and lower than 540 g/mol respectively. The reaction mechanism and structure of the $AB_2$ monomer, HTB and HTBE were investigated by MS, $^1H$ NMR and FTIR spectra technology. The molecular size of HTBE is under 8.65 nm and its shape is ellipsoid-like as determined by molecular simulation.