• 에너지공학
• /
• 제8권1호
• /
• pp.76-84
• /
• 1999

The demand of Small Self-generating System (SSS) including Small Cogeneration System (SCS) is constantly increasing with the need of electricity and/or thermal in office, hospital, hotel, and small factory, etc. It is especially recommended to operate SCS in the heat-following mode to maximize the efficiency of generator. In case of the heat-following mode SCS has got to be connected to distribution system so as to send surplus power to the utility or receive the short power from utility. But the interconnection of SSS with distribution system causes a few problems such as the bad power quality, and low security. If SSS is not promptly disconnected after faults occur (Islanding of SSS), it can not only damage equipment of utility and adjacent customers but also endanger life of human due to overvoltage or overcurrent. In this paper it has been deeply discussed if interconnection of engine self-generator/control system satisfies the protective requirement for SSS or not. 500 kW engine generator running in the Jodo island has been used to perform the analysis of interconnection.

• 전기학회논문지
• /
• 제63권7호
• /
• pp.916-923
• /
• 2014

This paper proposes a low-cost switched-mode rectifier (SMR) for a small-scale wind turbine with a permanent magnet synchronous generator (PMSG) system. Also, a sensorless Fuzzy MPPT control is realized by the proposed system. In the PMSG system with the SMR, the synchronous impedance can be replaced as the input inductor of a boost converter. Moreover, the sensorless MPPT control using the Fuzzy technique is carried out by the duty-ratio regulation of the SMR. The relation between the generating power and the duty-ratio is ruled by the chain rule. The wind turbine model is implemented by the squirrel cage induction motor and generated the variable torque when the generator speed is varied. To verify the performance of the proposed system, simulation and experimental results are executed.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -2
• /
• pp.1030-1033
• /
• 2002

This paper, a new simple controller operates in continuous conduction mode (CCM) for Boost power factor collection converter is introduced. The duty ratios are obtained by comparisons of a sensed signal from inductor current and a negative ramp carrier waveform in each switching period. By using the proposed controller, input voltage sensing, error amplifier in the current feedback loop, and analog multiplier／divider are not required, then, the control circuit implementation is very simple. To verify the proposed controller, the circuit simulation for Boost power factor correction converter was applied. For the results, the input current waveform was shaped to be closely sinusoidal, implying low THD.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 D
• /
• pp.1162-1164
• /
• 1997

This paper presents a power system stabilizer(PSS) using sliding mode-model following(SM-MF) including closed-loop f:edback(CLF) and compares the SM-MF PSS without CLF with that including CLF. The aim of this SM-MF PSS including CLF is to damp the low-frequency oscillation by using CLF and then is to obtain asymptotic tracking error between the reference model state and the plant state.

• 전력전자학회논문지
• /
• 제13권4호
• /
• pp.263-269
• /
• 2008

본 연구에서는 연속도통모드에서 단일 공진 인덕터를 사용하여 ZVT를 갖는 interleaved 부스트 컨버터를 제안한다. ZVT셀을 가지는 제안된 ZVT가지는 Interleaved 부스트 컨버터는 간단한 회로를 가지며 필터 사이즈 감소와 저 비용이 가능하다는 장점을 가진다. 또한 고 전력 응용에 적합하다. 본 논문에서 제안된 ZVT 가지는 IBC의 회로와 동작 원리를 자세히 설명하였다. 그리고 제안된 ZVT 기법의 타당성은 실험을 통하여 검증하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 추계학술대회 논문집 학회본부
• /
• pp.232-234
• /
• 1996

The self-refresh mode was introduced as method to reduce power dissipation in DRAM. Because the data retention time of DRAM cell decreases as the ambient temperature rises, the internal period in self-refresh mode must be limited by retention capability at the highest temperature in DRAM specification. Because of this, at room temperature($25^{\circ}C$) unnecessary power dissipation happens, If the period of self-refresh could be modulated as temperature, it is possible to reduce the self-refresh current. In this paper, new temperature detector circuit is suggested as this purpose.

• 조명전기설비학회논문지
• /
• 제16권3호
• /
• pp.101-109
• /
• 2002

원자력발전소 제어계통중 운전 정지에 많은 영향을 주고 제어하기 가장 까다로운 중기발생기 수위 제어는 특히 기동시 및 저 출력시에 자동제어는 물론 수동제어도 매우 어려운 상태이다. 중기발생시 수위특성을 분석하여 안정성이 보장된 증기발생기 수위 제어 계통의 제어방법을 개선하여 제어 성능과 신뢰도를 향상시킬 수 있는 알고리즘을 개발하고 디지털 제어 시스템으로 구현하여 실제 발전소에 설치 적용하였다.

• Journal of Power Electronics
• /
• 제18권3호
• /
• pp.714-722
• /
• 2018

This paper presents a wide-range speed control scheme of brushless DC (BLDC) motors based on a hall sensor with separated low- and normal-speed controllers. However, the use of the hall sensor signal is insufficient to detect motor speed in the low-speed region because of low sensor resolution and time delay. In the proposed method, a micro-stepping current control method according to the torque angle variation is presented. In this mode, the motor current frequency and rotating angle are determined by the reference speed without the actual speed fed by the hall sensor. The detected torque angle is used to adjust the current value in a limited band to control the current value in accordance with the load. The torque angle is detected exactly at the changing point of the hall sensor signal. The rotor can follow the rotating flux with the variable torque angle. In a normal speed range, the conventional vector control scheme is used to control the motor current with a PI speed controller using the hall sensor. The torque characteristics are analyzed on the basis of the back EMF and current shape. To adopt the vector control scheme, the continuous rotor position is estimated by the measured speed and hall sensor position. At the mode changing point between low and normal speed range, the proper initial current command and reference rotor position are calculated. The calculated current command can reduce the torque ripple during transient mode. The proposed method is simple but effective in extending the speed control range of a conventional BLDC motor with hall sensor without the need for a high-resolution encoder. The effectiveness of the proposed method is verified by various experiments on a practical BLDC motor.

• 한국전자파학회논문지
• /
• 제18권4호
• /
• pp.408-415
• /
• 2007

본 논문에서는 CMOS 0.18 um 공정을 이용하여 UWB(Ultra Wide Band) 시스템의 $3.1{\sim}4.8\;GHz$ 대역에서 사용할 수 있는 스위칭-이득 제어 저잡음 증폭기를 설계하였다. 높은 이득 모드에서 전력 이득은 12.5 dB, IIP3는 0 dBm, 소비 전류는 8.13 mA로 측정되었으며, 낮은 이득 모드에서는 전력 이득 -8.7 dB, IIP3는 9.2 dBm, 소비 전류는 0 mA로 측정 되었다.

• 조명전기설비학회논문지
• /
• 제20권5호
• /
• pp.49-56
• /
• 2006

양방향 컨버터는 연료전지 발전 시스템의 인버터 dc link와 저전압 배터리를 연결시켜 준다. 방전 모드(boost)에서는 저전압(battery: 48[V])측에서 고전압(dc link: 380[V])측으로, 충전 모드(buck)에서는 저전압측 배터리로 전력이 전달된다. 본 논문에서는 방전모드 시 MOSFET으로 구성된 1.5[kW] 능동 클램프 전류원 풀 브리지 컨버터가 동작하고 배터리 충전 시 IGBT로 구성된 전압원 하프 브리지 컨버터가 동작한다.