• Korean Journal of Soil Science and Fertilizer
• /
• v.12 no.4
• /
• pp.169-178
• /
• 1980

Ammonium nitrate explosion technique was applied to seek a convenient method for the establishment of orchard on the undulating to rolling land or hill side of Pogog clay loam soil (Fine Aquic Fragiudalfs : Planosols) having high bulk density and low permeability. Explosions were made by three ammonium nitrate explosives placed in the bottom of 90cm deep auger hole with every 2m interval (Explosion I) and 4m interval (Explosion II) respectively. The effect of the explosion on physical properties of the soil was investigated and compared with the effect induced by manual digging, excavation of $1m{\times}1m$ in diameter and depth (Manual digging I) and trenching of $1m{\times}1m{\times}25m$ in width, depth, and length (Manual digging II) respectively. The results investigated after 7 months from the treatments are summarized as follows : 1. The explosion or manual digging reduced bulk density and hardness, whereas the treatments increased porosity, hydraulic conductivity, and available moisture-holding capacity of the soil. 2. The explosion of 4 m interval improved physical properties of the soil to optimum level up to 70cm of the distance from the explosion core in the range of depth 0-60cm, while in the case of depth from 60 to 100cm the optimum level was achieved only within 50cm radius. 3. When exploded in 2 m interval, the effect in the 0-60cm depth was overlapped between two explosion cores. The effect in the depth between 60 and 100cm, however, was found to be independent of the explosion intervals. 4. The manual digging was only costly and laborious but effective only within the work-up zone. 5. For the soils having bulk density higher than $1.4g/cm^3$ after the treatments, the field capacity determined 72 hours after a heavy rain was lower than the laboratory estimate at the suction of 1/3 atm. 6. The top growth of apple tree for the first year revealed that the explosion seemed better treatment than the manual digging, even though the difference was insignificant.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.3
• /
• pp.444-450
• /
• 2012

The physical and chemical properties of soil in the Mangyeong and Dongjin river basin had been investigated in order to establish the most optimum soil improvement plan on the reclaimed land. The total soil area by reclamation in Saemangeum basin is 113,971 ha. The classification by the distribution of soil series and soil texture is as following. 13 soil series including Chonnam, Buyong and Chonbuk series are period-unknown areas. Regarding the soil texture, they are fine silty ~ clayey very fine. From 1920s to 1960s, Mangyeong, Gwanghwal and Chonbuk series had coarse silty textured soil. After the 1970s, Mangyeong, Gwanghwal, Munpo, Yeompo, Poseung, Gapo and Hasa series have more sandy soil ~ moderately coarse loamy textured soil. Regarding the chemical properties, the concentrations of EC, Exch. $K^+$, $Mg^{2+}$, $Na^+$ and pH are high regardless of the time of reclamation. On the other hand, organic matter (OM) of top soil were 3.3~16.1 g $kg^{-1}$. The organic matter contents were very low though the soil had been farmed for a long time. Furthermore, the deep soil had almost no organic matter with 5.6~1.1 g $kg^{-1}$. The reason is believed that there had not been any movement of OM and clay because pressure or induced pans had been formed by large agricultural machineries and poor vertical drain. Regarding the forming of illuvial horizon (B layer) which tells the development extent of soil, only in the Hwapo reclaimed area where rice had been cultivated for past 90 years, Fe and Mn from top soil are deposited at underground 20~30 cm with 7~8 cm thickness by the movement of clay. It is believed that it had been possible because the earthiness is silty clay loam soil with relatively high content of clay. The soils are soil with concern of damage from sea water, soil on flimsy ground and sandy soil. Therefore, soil improvement for stable crop production can be expected; if the water table would be lowered by subsurface drainage, the water permeability would be enhanced by gypsum and organic matter, and the sandy soil would be replaced by red soil with high content of clay.

• Journal of Chest Surgery
• /
• v.42 no.2
• /
• pp.148-156
• /
• 2009

Background: As cardiovascular operations become more complex and sophisticated, there is an increasing need for various bioprostheses for use as components of blood vessels and heart valves. We developed a fatigue stimuli test instrument to objectively evaluate the mechanical durability of a bioprosthesis, and we tested several currently known processing methods for bovine pericardium and we then compared the results. Material and Method: Fresh bovine pericardium was collected at the butcher shop with using aseptic technique, and each piece of pericardium was fixated and/or decellularized by 16 representative methods. We measured the permeability and compliance of the processed bovine pericardium samples, and measured them again after exposure to the fatigue stimuli. All the pieces of pericardium underwent microscopic examinations before and after the fatigue stimuli. Result: A mixture of glutaraldehyde and solvent treatment showed better mechanical durability than did the single glutaraldehyde treatment. High concentration glutaraldehyde treatment showed equal or no worse results than did low concentration glutaraldehyde treatment. After SDS (sodium dodecylsulfate) decellularization, the mechanical property of the bioprosthesis became much worse ($20{\sim}190$ times) and the mechanical durability to the fatigue stimuli was also very poor. Conclusion: We obtained the basic durability data after various fixation methods with using a home-made fatigue test instrument.

• Journal of Soil and Groundwater Environment
• /
• v.13 no.4
• /
• pp.1-7
• /
• 2008

This study analyzed for hydrodynamic dispersion characteristics of multi-soil layer (Silt and clay, Find sand, Coarse sand), data of a field tracer test on the multi-soil layer and data of laboratory column experiments on the samples on each soil layers. Through the analysis of permeability and flow, MS (Silt and clay) and FS (Fine sand), which were low effective porosity, were higher average linear velocity while CS (Coarse sand), which was high effective porosity, was higher hydraulic conductivity. Hydraulic conductivity function based on average soil particle diameter was assumed Y=$3.49{\times}10^{-8}e^{15320x}$ and coefficient of determination was 0.90. Average linear velocity function based on average soil particle diameter was assumed Y=$1.88{\times}10^{-7}e^{11459x}$ and coefficient of determination was 0.81. Longitudinal dispersivity function based on average soil particle diameter was Y = 0.00256$e^{5971x}$ and coefficient of determination was 0.98. According to the linear regression analysis of average linear velocity and longitudinal dispersivity, assumed function was Y = 21.7527x + 0.0063, and coefficient of determination was 0.9979. The ratio of field scale/laboratory scale was 54.09, it exhibited scale-dependent effect of hydrodynamic dispersion. Field longitudinal dispersivity (1.39m) was 7.47 times as higher than longitudinal dispersivity estimated by the methods of Xu and Eckstein (1995). Hydrodynamic dispersion on CS layer was occurred mainly by diffusion flow in the test aquifer.

• Asian Journal of Turfgrass Science
• /
• v.19 no.2
• /
• pp.115-123
• /
• 2005

The effect of sodium hypochlorite treatment on the germination of cattail (Typha spp.) seeds was investigated in growth chambers maintained on a 14-h photoperiod with various temperatures and light intensities. Germination rates of seeds were, in general, enhanced by the increase of light intensity and temperature regardless of cattail species. Seeds of T. oreientalis had 4.3, 13.0 and $7.3\%$ germination at temperatures of 20, 25 and $30^{circ}$C, respectively, under light intensity of 7.5${\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$. T. angustata showed higher germination rate, thus, 10.7, 22.7 and $50.7\%$ under same temperature and light environment. Under high light intensity of 79.5${\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, the germination rates of T. oreintalis and T angustata were $78.3\%$ and $88.7\%$ at $30^{circ}$C, respectively. Scarification of seeds with NaOC1 ($4\%$, available chlorine) increased germination rate in both species, especially even at low temperature of $20^{circ}$C. Germination speed was also enhanced by NaOC1 treatment. High light intensity further increased the germination rate. When NaOC1 treated seeds were sowed on the soil surface in plastic house, the seedling emergence was nearly $100\%$. Untreated seeds of T. oreintalis and T. angustara showed 40 and $50\%$, respectively, in germination under same condition. However, when the depth of soil covering was over 1.0 cm, seedling emergence was retarded more than 1 month. On the process of seedling development, emergence of mesocoty1 occurred firstly and after than primary root and first leaf were developed on the end of elongated mesocotyl. These results suggest that the promotion of seed germination by NaOC1 pretreament may be induced from the increase of light absorptivity as well as water permeability through scarifying and bleaching the seed coat.

• Journal of Bio-Environment Control
• /
• v.22 no.2
• /
• pp.167-174
• /
• 2013

Six kinds of sprout vegetables were applied three and six types of non-perforated breathable propylene films (NPB film) for individual and mixed modified atmosphere (MA) package condition at $10^{\circ}C$ on this study. As a tah tasai, kohlrabi, rape, chinese cabbage, red radish, broccoli sprouts were packaged by 20,000, 60,000, and 100,000 $cc{\cdot}m^{-2}{\cdot}day{\cdot}atm$ non-perforated breathable films for seven days storage. Mixed sprout vegetables were used 20,000 cc, 40,000 cc, 60,000 cc, 80,000 cc, and 100,000 $cc{\cdot}m^{-2}{\cdot}day{\cdot}atm$ non-perforated breathable films for seven days storage. Loss rate of fresh weight, changes of carbon dioxide, oxygen, and ethylene gas concentration were measured during the storage. Visual quality and off-flavor were rated by panel tests after seven days storage. Each sprout vegetable storage with film tests had been shown under the 0.5% fresh weight loss in every packaged films, and the 20,000cc NPB film package had been suitable atmosphere condition in the carbon dioxide and oxygen gas concentration. Appearance and off-odor of sprouts packaged with 20,000cc NPB film were shown better than other films because of the proper gas movement through the film to outside during the storage. Fresh weight loss of the mixed sprout vegetables had no difference among the NPB films for seven days storage. The 20,000 cc film had been resulted in that exchange rate of carbon dioxide and oxygen was highest cause of low film permeability than sprouts respiration. But the film is not good for storage because it has been made poor value of off-order even showed high visual quality from panel test after storage. 40,000 cc and 60,000 cc non-perforated breathable films were more suitable for mixed sprout vegetable storage at $10^{\circ}C$. These result suggested that 20,000 cc NPB film was good for single packaged sprout vegetable and 40,000 cc and 60,000 cc non-perforated breathable films were good for mixed packaged sprout vegetable.

• Tunnel and Underground Space
• /
• v.30 no.4
• /
• pp.359-381
• /
• 2020

Within the framework of DECOVALEX-2019 Task D, full-scale engineered barriers experiment (FEBEX) at Grimsel Test Site was numerically simulated to investigate an applicability of implemented Barcelona basic model (BBM) into TOUGH2-MP/FLAC3D simulator, which was developed for the prediction of the coupled thermo-hydro-mechanical behavior of bentonite buffer. And the calculated heater power, temperature, relative humidity, total stress, saturation, water content and dry density were compared with in situ data monitored in the various sections. In general, the calculated heater power and temperature provided a fairly good agreement with experimental observations, however, the difference between power of heater #1 and that of heater #2 could not captured in the numerical analysis. It is necessary to consider lamprophyre with low thermal conductivity around heater #1 and non-simplified installation progresses of bentonite blocks in the tunnel for better modeling results. The evolutions and distributions of relative humidity were well reproduced, but hydraulic model needs to be modified because the re-saturation process was relatively fast near the heaters. In case of stress evolutions due to the thermal and hydraulic expansions, the computed stress was in good agreement with the data. But, the stress is slightly higher than the measured in situ data at the early stage of the operation, because gap between rock mass and bentonite blocks have not been considered in the numerical simulations. The calculated distribution of saturation, water content, and dry density along the radial distance showed good agreement with the observations after the first and final dismantling. The calculated dry density near the center of the FEBEX tunnel and heaters were overestimated compared with the observations. As a result, the saturation and water content were underestimated with the measurements. Therefore, numerical model of permeability is needed to modify for the production of better numerical results. It will be possible to produce the better analysis results and more realistically predict the coupled THM behavior in the bentonite blocks by performing the additional studies and modifying the numerical model based on the results of this study.

• Korean Journal of Soil Science and Fertilizer
• /
• v.11 no.3
• /
• pp.145-160
• /
• 1979

The effects of organic material application on soil physical properties were reviewed in relation to soil productivity. The organic matter contents and soil physical properties of the cultivated land in Korea were summarized and the effects of organic matter were compared in terms of land uses and soil types. Soil physical properties related to crop yield potential, such as soil aggregation, permeability, water holding capacity, erodibility, and compactibility, were used in evaluating the effects of organic materials as a soil physical amendment. The benefical effects of organic matter addition on soil physical conditions include (1) better aeration and increased infiltration in silty and clayey soils, (2) increased water holding capacity and moisture availability in sandy soils, (3) decreased soil erodibility, and (4) increased resistance to compaction. It is, therefore, concluded that continuous application of organic materials could greatly improve the various soil physical properties and favor the growth and yield of crops. A high rate of organic matter addition could contribute to reducing not only the soil erosion on sloping land, but also the possible detrimental effect of farm mechanization. In general, the effects of organic matter on soil physical improvement were estimated to be much higher in upland than in paddy. Organic matter would have a more pronounced effect on low productive lands such as heavy clayey or sandy soils and newly reclaimed soil. The optimum level of soil organic matter content was estimated to be about 3.0 to 3.5% for the best soil physical condition. Since the organic matter contents of the cultivated lands in Korea are much lower than optimum level, it would be desiable to use more organic materials to soil for the increase of soil productivity, continuation of stabilized high productivity and soil erosion control.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.2
• /
• pp.103-109
• /
• 2009

Soils originated from limestone, located at the southern part of Kangwon province and Jecheon, Danyang of Chungbuk province are mainly composed of fine texture, and have different properties from soils originated from granite and granite gneiss, especially for water movement. This study was conducted for classification of hydrologic soil group (HSG) of soils originated from limestone by measuring the infiltration rate of surface soils and percolation rate of sub soils. Soils used for the experiment were 6 soils in total : Gwarim, Mosan, Jangseong, Maji, Anmi and Pyongan series. Infiltration and percolation rate were measured by a disc tension infiltrometer and a Guelph permeameter, respectively. Particle size distribution and organic matter content of the soils were analyzed. HSG, which was made by USDA NRCS(National Resources Conservation Service) for hydrology, of Gwarim series with O horizon of accumulated organic matter was classified as type A which show the properties of low runoff potential, rapid infiltration and percolation rate. HSG of Mosan series, which has high gravel content and very rapid permeability, was classified as type B/D because of the impermaeble base rock layer under 50cm from surface. HSG of Jangseong series with shallow soil depth was classified as type C/D owing to the impermaeble base rock layer under 50cm from surface. HSG of Maji series was type B, and HSG of Anmi series used as paddy land was type D because of slow infiltration and percolation rate caused by the disturbance of surface soil by puddling. HSG of Pyeongan series having a sudden change of layer in soil texture was type D because of the slow percolation rate caused a the layer.

• 보존과학연구
• /
• s.33
• /
• pp.45-55
• /
• 2012

A beeswax-treated paper has no air permeability but has the water repellency compared with a general Hanji. Because of these properties, the differences of the aging factors and mechanisms between the outer partition of beeswax-treated paper that is affected by the surrounding conservation environment and the inner partition of it that is not affected are bigger than general books. In this research, we analyzed and compared the aging characteristics through the accelerated aging of the beeswax-treated paper by some air and humidity conditions. The results of the physical and optical analysis after the artificial aging, it was shown that the oxygen accelerates the aging of the beeswax-treated paper and the condition with the humidity 50% RH is more stable than the condition with the humidity 0% RH. The results of the CG/MS analysis that was conducted to figure out the decomposition charateristics of the beeswax according to the air quality and the humidity, a low molecular weight compound that the number of carbon is C9-C20 including a fatty acid such as a palmitic acid was increased as the aging was progressed. However, under the same environment, a compound that the number of carbon is C21-C36 including a hydrocarbon and a aliphatic alcohol and a high molecular weight compound that the number of carbon is more than C34 including a wax ester were decreased. A rate of change according to the air quality and the humidity was similar to the beeswax-treated papers.