• Solar Energy
• /
• v.10 no.3
• /
• pp.19-26
• /
• 1990

Theoretical analysis for the thermal performance on the low-cost trickle collector, which is easy to manufacture and construct, has been performed. The results were in reasonably good agreement with those of the experiments. They have been applicable to predict long-term thermal performance on the low-cost solar collecting system. The dialogue type of computer program has been written based on the f-chart method and it can be used for designing a these collecting system, and investigating its economic feasibility.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.8
• /
• pp.845-850
• /
• 2009

Localization which estimates a robot's position and orientation in a given environment is very important for mobile robot navigation. Although low-cost sensors are preferred for practical service robots, they suffer from the inaccurate and insufficient range information. This paper proposes a novel approach to increasing the success rate of low-cost sensor-based localization. In this paper, both the previous and the current data obtained from the IR sensors are used for localization in order to utilize as much environment information as possible without increasing the number of sensors. The sensor model used in the monte carlo localization (MCL) is modified so that the accumulated range information may be used to increase the accuracy in estimating the current robot pose. The experimental results show that the proposed method can robustly estimate the robot's pose in indoor environments with several similar places.

• Proceedings of the KIEE Conference
• /
• 2005.10b
• /
• pp.603-605
• /
• 2005

In this paper, we deal with a calibration method for low cost motion capture sensor using PSD (Position Sensitive Detection). The PSD sensor is employed to measure the direction of incident light from moving markers attached to motion body. To calibrate the PSD optical module, a conventional camera calibration algorithm introduced by Tsai. The 3-dimensional positions of the markers are measured by using stereo camera geometry. From the experimental results, the low cost motion capture sensor can be used in a real time system.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.7
• /
• pp.17-24
• /
• 1998

We proposed a novel bondwire inductor buried in plastic package for low cost MMIC and characaterized the electrical perofmrance in a wide frequency range using the full-wave analysis of finite element method(FEM), and then we fabricated and measured the scale-up model in order to prove the characteristics. Th ebondwire inductor has higher quality factor and higher cutoff frequency than the conventional spiral inductor designed n the same area as the bondwire inductor. Since the air-bridge process is not requried for the bondwire inductor, it is very suitable for low cost plastic-packaged MMIC production. The bondwire inductor has the field distribution localized around the bondwire inductor and hence is more compatible to the crosstalk problems.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.2
• /
• pp.21-26
• /
• 1997

The dielectric effects on the parasitics of bondwires buried in slightly-lossy dielectric materials hav been investigated over a wide frequency range using the method of moments with incorporation of ohmic and dielectric losses. The FR-4 composite is widely used as a basis material for PCB and plastic packages, because of it sinherent electricl and chemical stbility and low cost. The cole-cole model, which is representative complex permittivity model of epoxy polymers, has been applied to consider the dielectric effects in the MoM calculation. The prasitic impedance of a grounded bondwire in FR-4 composite is greatly increased due to the dielectric loading effect enhanced by the radiation at high frequencies. These calculation results will be helpful for designing and packaging of high-frequency low-cost IC's.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.930-931
• /
• 2008

This study is on the development of a low cost inverter module with Power Factor Correction(PFC) circuit which satisfies the international harmonic current standard such as IEC61000-3-2. In this study, the performances of the PFC circuit applying a new control method are simulated and verified by Matlab/Simulink. Also, the inverter module with the designed PFC circuit is implemented and the experimental results for the module are presented. Finally, through an analysis for the results of the simulation and the experiment, the merits obtainable by applying the PFC circuit when designing an inverter module are discussed and presented.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.2
• /
• pp.61-68
• /
• 2006

Many researchers have worked for the sensorless control of SynRM in recent years. However they commonly requires large calculations which induced from its complexity. For low cost application as like home appliance, it is difficult to utilize because of the cost problem. Therefore, it is necessary to introduce simplified sensorless control scheme that is composed of least calculation to estimate the rotor position. In this paper the sensorless control is performed using the characteristics of SynRM structure in which the linkage flux varies with rotor position, so the rotor position can be detected by the change of linkage flux. The estimation of linkage flux can be acquired from the integration of the motor terminal voltage which is commonly used method for the reliability of the estimation. However this estimation method has demerits in low speed operation therefore in that region the motor terminal voltage is compensated by the phase current. A digital simulation (MATLAB) and experiment were performed to confirm the adequacy of the proposed control scheme.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2015.07a
• /
• pp.279-281
• /
• 2015

Location awareness is an important capability for mobile-based indoor services. Those indoor services have motivated the implementation of methods that need high computational load cost and complex mechanisms for positioning prediction. These mechanisms, such as opportunistic sensing and machine learning, require more energy consumption to achieve accuracy. In this paper, we propose the Bluetooth Low Energy indoor zone detection (BLEIZOD) technique. This method exploits the concept of proximity zone to reduce the load cost and complexity. Our proposed method implements the received signal strength indicator (RSSI) function more effectively to gain accuracy and reduce energy consumption.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.1
• /
• pp.147-155
• /
• 2017

A new endurance test-pattern generation on NAND-flash memory is proposed to improve test cost. We mainly focus on the correlation between the data-pattern and the device error-rate during endurance testing. The novelty is the development of testing method using quasi-random pattern based on device architectures in order to increase the test efficiency during time-consuming endurance testing. It has been proven by the experiments using the commercial 32 nm NAND flash-memory. Using the proposed method, the error-rate increases up to 18.6% compared to that of the conventional method which uses pseudo-random pattern. Endurance testing time using the proposed quasi-random pattern is faster than that of using the conventional pseudo-random pattern since it is possible to reach the target error rate quickly using the proposed one. Accordingly, the proposed method provides more low-cost testing solutions compared to the previous pseudo-random testing patterns.

• Korean Journal of Optics and Photonics
• /
• v.16 no.4
• /
• pp.345-353
• /
• 2005

We proposed a new and cost-effective method fer assembling holographic pickup modules without any high resolution vision system. Assembling was accomplished by adjusting photodiode package only, leading to a low cost, holographic pickup module. Focus and tracking error signals were simply determined by comparing spot sizes and by using the 3 beam method, respectively, based on four-sectional holographic optical elements. In experiment, we assembled a hologram module and estimated performance of the proposed method fur a holographic pickup module used in compact disc system.