• Applied Science and Convergence Technology
• /
• v.23 no.1
• /
• pp.27-33
• /
• 2014

We have studied photovoltaic characteristics of single-junction GaAs solar cells with/without an $MgF_2/ZnS$ anti-reflective coating (ARC) illuminated by low-density concentration (<10 suns). By the ARC deposition, the short-circuit current density ($J_{SC}$) and the fill factor (FF) are increased by $5mA/cm^2$ and 5% at a standard illumination (1 sun), respectively, and the resulted conversion efficiency is enhanced by 45%. In contrast with the cell with no ARC showing a rapid degradation with increasing concentration power, the efficiency of ARC-deposited cell remains almost constant as ($17.7{\pm}0.3$)% regardless of the concentration. It informs that ARC treatment is very effective in GaAs concentrator solar cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.481.1-481.1
• /
• 2014

Dye-sensitized solar cell (DSSC) has been extensively investigated as the next generation energy source. Despite attractive features of simple fabrication process and its economical efficiency, there are some problems such as low efficiency and low long-term stability. Many groups have attempted the proposed way to improve the cell efficiency and long-term stability such as low recombination rate between $TiO_2$ surface and electrolyte, the development of new dye molecules capable of light adsorption as broadly as possible, the fabrication of a solid-state DSSC by replacing the liquid electrolyte, and protective coating on glass. In this work, we confirmed new dye-coating conditions to maximize the dye adsorption between the dye and $TiO_2$ nanoparticle surface. The experiment results coating conditions with the coating temperature of $70^{\circ}C$, the dye concentration of 10 mM and the coating time of 3 min. Conditions have two times, three times cycle the experiment in progress efficiency rises.

• KSBB Journal
• /
• v.19 no.3
• /
• pp.221-225
• /
• 2004

Bacillus polyfermenticus SCD derived from Bacillus sp., which is commonly called as Bisroot$^{ⓡ}$. The goal of this study, is to Increase stability of Bacillus polyfermenticus SCD in low pH, high temperature and high glucose concentration via three layer coating. The viability of coated Bacillus polyfermenticus SCD increased to 30%, 20%, 14% in the condition of pH 2 4 6 than that of uncoated Bacillus polyfermenticus SCD at 37$^{\circ}C$ for 4 h. Final viability of the coated Bacillus polyfermenticus SCD in 80$^{\circ}C$ increased to 40% than that of uncoated Bacillus polyfermenticus SCD. In high glucose concentration coated Bacillus polyfermenticus SCD is more stable than uncoated about 50%. In conclusion, the three layer coated Bacillus polyfermenticus SCD is very stable for low pH, high temperature and high glucose concentration.

• Food Science of Animal Resources
• /
• v.38 no.3
• /
• pp.636-652
• /
• 2018

The study aims to determine the optimum sterilization rate and water activity of Chinese traditional smoke-cured bacon product (Larou) in the preservation with natural coating solution. With the response surface methodology (RSM), we analyzed 3 factors of processing conditions (the concentration of lysozyme, concentration of sodium alginate, and concentration of chitosan) and 2 response factors (sterilization rate and water activity). Sterilization rate and water activity of Larou were largely affected by the concentration of lysozyme, concentration of sodium alginate, and concentration of chitosan. The final optimum concentrations of lysozyme, sodium alginate, and chitosan were 0.09, 1.40, and 1.60% and realized the high sterilization rate. Water activity of sliced Larou was significantly correlated with the sterilization rate. Low-field nuclear magnetic resonance analysis verified the optimum processing conditions. The coating resulted in 99.69% rate of reducing bacteria after 30-day storage. The data of the total number of colony, peroxidation value, moisture content, pH, and sensory evaluation provided the theoretical basis for extending the shelf life of Chinese traditional smoke-cured bacon product (Larou) with natural coating solution.

• Fibers and Polymers
• /
• v.2 no.3
• /
• pp.148-152
• /
• 2001

Cotton yarns were coated with a polymer solution to hold surface fibers to the yam body, which caused fiber-fly generation during knitting process. The physical property of the coated yarn, especially a bending rigidity was investigated in order to evaluate the performance of the coated yam during knitting. SEM images showing the surface condition of the coated yarn demonstrated that the thickness of a coating material increased as the concentration of the coating solution increased. The results of the bending rigidity measured using KES-FB2 system showed that the bending rigidity of the coated yam increased as the concentration of the coating solution increased. The results also revealed the possibility that yarn coated with a low amount of coating material should be employed for further research of reducing fiber-fly generation during knitting process.

• Journal of Surface Science and Engineering
• /
• v.46 no.6
• /
• pp.277-282
• /
• 2013

This study is an experimental attempt to confirm the binder effect of zeolite coating on glass plate by heat treatment. As a result, zeolite was successfully formed with low concentratios of pressure, whose concentration was effective in 10% or more for thin film zeolite coating. And as the content of the binder (TEOS) in mixed coating solution was higher, the zeolite was fastened better on the surface. Above 5% content of the binder in the coating solution, TEOS hindered zeolite synthesis of the precursor and brought to zeolite capacity decrease. Furthermore, when the concentration of the precursor, sedimentation rate of the precursor was higher and the coating efficiency is reduced thereby. Therefore, the most effective concentrations of the precursor and TEOS in the coating solution was 10% and 5%, respectively. It was concluded that zeolite coating is produced by heat treatment method after dipping without hydrothermal synthesis.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.124.2-124.2
• /
• 2016

Corrosion resistance and adhesion of electro-paint (E-paint) with fluoride conversion coating (FCC) on AZ31 Mg alloy were studied. Corrosion resistance and adhesion were studied as a function of FCC-treatment time and concentration of FCC-bath. Aqueous hydrogen fluoride (HF) solutions, with concentrations ranging from 0.5 M to 5 M, were used to form FCC on chemically polished AZ31 Mg alloy samples for six different times; 10, 30, 60, 90, 120, and 180s. The results from salt spray test (SST) showed that corrosion resistance of E-paint appeared to decrease with increasing FCC treatment times in low concentration FCC baths. The number of blisters formed on the FCC-treated samples increased with increasing FCC treatment time of more than 1 min in low concentration (0.5 M to 1 M) solutions. On the other hand, samples treated in the 5 M HF solution for 120s showed no delamination or blistering even after 1200h of SST.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.39 no.4
• /
• pp.29-37
• /
• 2007

The effects of latex particle size, basis weight of base paper and coating color concentration on the printing quality of coated paper were investigated. Coating colors were prepared with five types of latexes having different particle sizes. Coated papers were produced with high solid coating colors and with low solid coating colors in a industrial coater, respectively. In high solid coating colors, rheology modifier was used and GCC content was high. It was concluded that, in order to control binder migration and hence print mottle, latex particle sizes shall be controlled as well as formation, sizing degree and roughness of basis paper.

• Corrosion Science and Technology
• /
• v.18 no.1
• /
• pp.24-32
• /
• 2019

The effects of zinc coating and heat treatment on the corrosion resistance of aluminum alloys including A1100 and the modified A3003, used as heat exchanger tube were investigated in this study. The grain size of the heat-treated specimen is larger than that of the specimen without heat treatment, but the grain size did not significantly affect the corrosion behavior. The concentration of zinc was noted at 11.3 ~ 31.4 at.% for the as-received Zn-coated samples and reduced to 1.2 ~ 2.4 at.% after the heat treatment, as measured by the scanning electron microscopy (SEM) with an energy dispersive spectrometer (EDS) on the surface. The concentration of oxygen is 22 ~ 46 at.% for the zinc coated specimens while noted at 7.4 ~ 12.8 at.% for the specimens after the removal of the coating. The corrosion behavior depended largely on the concentrations of zinc, aluminum, and oxygen on the specimen surface, but not on the Mo content. The corrosion potential was high and the corrosion rate was low for a specimen with a low zinc content, a high aluminum content, and a high oxygen content.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.416-416
• /
• 2016

Organic-inorganic metal halide perovskite solar cells have received attention because it has a number of advantages with excellent light harvesting, high carrier mobility, and facile solution processability and also recorded recently power conversion efficiency (PCEs) of over 20%. The major issue on perovskite solar cells have been reached the limit of small area laboratory scale devices produced using fabrication techniques such as spin coating and physical vapor deposition which are incompatible with low-cost and large area fabrication of perovskite solar cells using printing and coating techniques. To solution these problems, we have investigated the feasibility of achieving fully printable perovskite solar cells by the blade-coating technique. The blade-coating fabrication has been widely used to fabricate organic solar cells (OSCs) and is proven to be a simple, environment-friendly, and low-cost method for the solution-processed photovoltaic. Moreover, the film morphology control in the blade-coating method is much easier than the spray coating and roll-to-roll printing; high-quality photoactive layers with controllable thickness can be performed by using a precisely polished blade with low surface roughness and coating gap control between blade and coating substrate[1]. In order to fabricate perovskite devices with good efficiency, one of the main factors in printed electronic processing is the fabrication of thin films with controlled morphology, high surface coverage and minimum pinholes for high performance, printed thin film perovskite solar cells. Charge dissociation efficiency, charge transport and diffusion length of charge species are dependent on the crystallinity of the film [2]. We fabricated the printed perovskite solar cells with large area and flexible by the bar-coating. The morphology of printed film could be closely related with the condition of the bar-coating technique such as coating speed, concentration and amount of solution, drying condition, and suitable film thickness was also studied by using the optical analysis with SEM. Electrical performance of printed devices is gives hysteresis and efficiency distribution.