• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2015.10a
• /
• pp.279-282
• /
• 2015

Fisheries development of the basic law pursuant to article 15 (marine safety management, etc.) one of maritime safety and maritime traffic facilities nationwide network of DGPS in accordance with the building maximize infrastructure utilization and country. Source technology has been improving steadily raised for the benefit daegukmin. In particular, look at the type of product for the marine supply medium-wave receiver Performance products that satisfy most of the IMO Advisory. The antenna and receiver are separate structural supply for some integrated model with a very high Rather it is used as a portable receivers for marine positioning cheap integrated model development is needed. Correction of satellite navigation receivers for the current Marine GPS module, medium-wave modules can be developed one low cost Integrated in independent operating environments do not support the model development done look at what the problem is 285kHz ~ 315kHz in DGPS Beacon receiver structure using a medium wave or Beacon The medium-wave antenna and a GPS receiver signal to noise ratio was studied GPS signal attenuation on the DGPS performance looked at each GPS manufacturer medium-wave signal-to-noise ratio and normalized impact by GPS manufacturers noise power ratio per bandwidth for medium-wave GPS signals affect it was implemented to improve performance.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.7
• /
• pp.678-685
• /
• 2013

In this paper, we propose a design of dual-band patch antennas for Global Positioning System(GPS) applications, and the designed antenna is used as an individual element of GPS arrays. A low distortion and a high isolation of the array are achieved by adjusting rotating angles of each array element. The antenna consists of two radiating patches that operate in the GPS $L_1$ and $L_2$ bands, and the two ports feeding network with a hybrid chip coupler is adopted to achieve a broad circular polarization(CP) bandwidth. The rotating angles of each antenna element are varied with four directions(${\phi}=0^{\circ}$, ${\phi}=90^{\circ}$, ${\phi}=180^{\circ}$, ${\phi}=270^{\circ}$) in order to minimize the pattern distortion and maximize the isolation among array elements. The measurement shows bore-sight gains of 0.3 dBic($L_1$) and -1.0 dBic($L_2$) for the center element. Bore-sight gains of 1.6 dBic($L_1$) and 1.0 dBic($L_2$) are observed for the edge element. This results demonstrate that the proposed antenna is suitable for GPS array applications.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.255-258
• /
• 2011

Wi-Fi is a rapidly spreading communications network with Smart phone's publication, the technology has become Ubiquitous-based core network which is connected to personal computers, laptops, and tablet PC. Wi-Fi can send currently a variety of data standard due to developed wireless LAN communications network. One of Wi-Fi standard protocols, which is IEEE 802.11n, use 2.4GHz and 5GHz band. 2.4GHz band is used for 802.11b/g protocol because wavelength is long, diffraction and receiving distance is enough to connect other device. 5GHz band has more available channels to use than 2.4GHz band, so there is no frequency interference of other wireless device such as Bluetooth, RFID. Moreover, there is low interference between channels due to small users in each bandwidth level. In the thesis, we are going to analyze 802.11a/b/g protocol which has used since the beginning of Wi-Fi protocol and 802.11n protocol which is used lately. Furthermore, we look into development and direction for standardization of the next generation wireless LANs which are 802.11ac and 802.11ad. In addition, we will consider for the security, vulnerabilities and its countermeasure in Wireless LAN.

• Journal of KIISE:Databases
• /
• v.30 no.5
• /
• pp.476-493
• /
• 2003

Data broadcast is an effective data transmission method from a data base server to numerous mobile clients due to the restrictions on mobile environment such as low wireless communication bandwidth and energy shortage of mobile devices. There are various broadcast methods based on clients' data access frequencies or semantic relationship of data. The broadcast schedule based only on the access frequencies does not consider semantic relations of data, so that when a client needs to access a series of semantically related data, the client has to listen to the wireless channel for a long time. On the other hand, the broadcast schedule based only on semantic relationship of data makes data access time longer when clients highly request specific data which are not semantically related but frequently accessed. In this paper, we present an efficient data broadcast method based on not only data access frequencies but also semantic relationship to improve mobile clients' query response time. The new hybrid broadcast method we propose creates a data broadcast schedule according to the data access frequencies and then the schedule is adjusted to reflect semantic relationship of data. We show our method is efficient by experimental performance analysis.

• The KIPS Transactions:PartC
• /
• v.9C no.1
• /
• pp.73-78
• /
• 2002

In WATM networks, in order to perform dynamic slot allocation required slots of mobile terminals are estimated based on DP (Dynamic Parameter) reflecting characteristics of traffic. In VBR (Variable Bit Rate) traffic, slot allocation is done at MT considering both time-dependent characteristics and QoS (Quality of Service) requirements. In this paper, DPs-buffer state information and buffer state change-are transmitted through in-band signaling. BS (Base Station) performs dynamic slot allocation considering traffic characteristics of each MT (Mobile Terminal), in other words, buffer state information informs the potentiality of 'buffer full state'to BS if MT buffer is over the specific threshold value and buffer state change notifies change in buffer state of incoming cells to MT. If buffer state information is equal to 'low (more than threshold)' and 'abrupt increase' it generates 'buffer full' state cell transmission delay or cell loss might occur. At this time BS should assign additional slots to MT, and then MT consumes cells in its buffer. In simulation, the proposed scheme shows better performance in cell delay and loss than EPSA (Estimation-Prorated Slot Assignment) in-band scheme.

• Journal of Sensor Science and Technology
• /
• v.10 no.1
• /
• pp.1-8
• /
• 2001

Conventional microgyroscopes of vibrating type require resonant frequency tuning of the driving and sensing modes to achieve high sensitivity. These tuning conditions depend on each fabricated microgyroscopes, even though the microgyroscopes are identically designed. A new micromachined resonator, which is applicable to microgyroscopes with self-toning characteristics, is presented. Since the laterally driven two degrees of freedom (2DOF) resonator was designed as a symmetric structure with identical stiffness in two orthogonal axes, the resonator is applicable to vibrating microgyroscopes, which do not need mode tuning. A dynamic model of the resonator was derived considering gyroscopic application. The dynamic model was evaluated by experimental comparison with fabricated resonators. The microgyroscopes were fabricated using a simple 2-mask-process of a single polysilicon layer deposited on an insulator layer. The feasibility of the resonator as a vibrating microgyroscopes with self-tuning capability is discussed. The fabricated resonators of a particular design have process-induced non-uniformities that cause different resonant frequencies. For several resonators, the standard deviations of the driving and sensing frequencies were as high as 1232Hz and 1214Hz, whereas the experimental average detuning frequency was 91.75Hz. The minimum detuned frequency was 68Hz with $0.034mVsec/^{\circ}$ sensitivity. The sensitivity of the microgyroscopes was low due to process-induced non-uniformity; the angular rate bandwidth, however, was wide. This resonator could be successfully applicable to a vibrating microgyroscopes with high sensitivity, if improvements in uniformity of the fabrication process are achieved. Further developments in improved integrated circuits are expected to lower the noise level even more.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.4
• /
• pp.653-660
• /
• 2001

In this paper, we designed 2303.15MHz frequency synthesizer for the purpose of the phase noise prediction. For the modeling of phase noise generated in the designed system through introducing the noise-modeling method suggested by Lascari we analyzed a variation of phase noise as according as that of offset frequency. Especially, for the third-order system of the PLL among some kinds of phase noise generated from VCO we analyzed the aspect of 1/f-noise appearing troubles in the low frequency band. Since it is difficult to analyze mathematically 1/f-noise in the third-order system of the PLL, introducing the concept of pseudo-damping factor has made an ease of the access of the 1/f-noise variance. we showed a numerical formula of 1/f-noise variance in the third-order system of the PLL which is compared with that of 1/f-noise variance in the second-order system of the PLL. As a result, In case of txco we found the reduce rapidly along the offset frequency after passed through that phase-noise was -160dBc/Hz before passed through a loop at 10kHz offset frequency and -162.6705dBc/kHz after passed through the loop, -180dBc/Hz at 100kHz offset frequency and -560dBc/kHz after passed through the loop. We can notice that the variance of third-order system more occurs (or the variance of second-order system in connection with noise bandwidth and variance factor of second-order and third-order system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.3
• /
• pp.1393-1401
• /
• 2013

What is RFID Microchip tag attached to an object, the reader recognizes technology collectively, through communication with the server to authenticate the object. A variety of RFID tags, 13.56Mhz bandwidth RFID card, ISO/IEC 14443 standards based on NXP's Mifare tag occupies 72.5% of the world market. Of the Mifare tags, low cost tag Mifare Classic tag provided in accordance with the limited hardware-based security operations, protocol leaked by a variety of attacks and key recovery vulnerability exists. Therefore, in this paper, Cryptography Scheme and Secure Protocol for Safety Secure Scheme Construction in 13.56Mhz RFID have been designed. The proposed security scheme that KS generated by various fixed values and non-fixed value, S-Box operated, values crossed between LFSR and S-Box is fully satisfied spoofing, replay attacks, such as vulnerability of existing security and general RFID secure requirement. Also, It is designed by considering the limited hardware computational capabilities and existing security schemes, so it could be suit to Mifare Classic now.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.2
• /
• pp.211-218
• /
• 2014

Recently, software-based programmable logic controller (PLC) systems, which are implemented in standard PLC languages on general hardware, are gaining popularity because they overcome the limitations of classical hardware PLC systems. Another noticeable trend is that the use of integrated development environment (IDE) is becoming important. IDEs can help developers to easily manage the growing complexity of modern control systems. Furthermore, industrial Ethernet, e.g. EtherCAT, is becoming widely accepted as a replacement for conventional fieldbuses in the distributed control domain because it offers favorable features such as short transmission delay, high bandwidth, and low cost. In this paper, we implemented the extension of open source IDE, called Beremiz, for developing EtherCAT-based real-time, synchronized motion control applications. We validated the EtherCAT system management features and the real-time responsiveness of the control function by using commercial EtherCAT drives and evaluation boards.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.6
• /
• pp.95-102
• /
• 2012

In this paper, we propose a method that can construct efficiently a P2P overlay multicast network composed of many heterogeneous peers in communication bandwidth, processing power and a storage size by selecting a peer in a distributed fashion using an ant-colony theory that is one of the computational intelligence methods. The proposed method considers not only the capacity of a peer but also the number of children peers supported by the peer and the hop distance between a multicast source and the peer when selecting a parent peer of a newly joining node. Thus, an P2P multicast overlay network is constructed efficiently in that the distances between a multicast source and peers are maintained small. In addition, the proposed method works in a distributed fashion in that peers use their local information to find a parent node. Thus, compared to a centralized method where a centralized server maintains and controls the overlay construction process, the proposed method scales well. Through simulations, we show that, by making a few high capacity peers support a lot of low capacity peers, the proposed method can maintain the size of overlay network small even there are a few thousands of peers in the network.