• Journal of Power Electronics
• /
• v.10 no.4
• /
• pp.405-411
• /
• 2010

This paper proposes a novel tracking algorithm considering radiation to improve the power of a photovoltaic (PV) tracking system. The sensor method used in a conventional PV plant is unable to track the sun's exact position when the intensity of solar radiation is low. It also has the problem of malfunctions in the tracking system due to rapid changes in the climate. The program method generates power loss due to unnecessary operation of the tracking system because it is not adapted to various weather conditions. This tracking system does not increase the power above that of a power of tracking system fixed at a specific position due to these problems. To reduce the power loss, this paper proposes a novel control algorithm for a tracking system and proves the validity of the proposed control algorithm through a comparison with the conventional PV tracking method.

• Journal of Korean Society of Water and Wastewater
• /
• v.23 no.4
• /
• pp.447-458
• /
• 2009

Energy loss at manholes, often exceeding friction loss of pipes under surcharged flow, is considered as one of the major causes of inundation in urban areas. Therefore, it is necessary to analyze head loss at manholes, especially in case of surcharged flow. Hydraulic experiments were conducted with three cases. Case A is to test whether the shapes of the manholes influence head loss coefficients. Case B and C were proposed to further reduce head losses by improving the manhole hydraulic efficiency. In case B, the joining part of the pipe at both shapes of manholes is shifted from central part to side part. The test in case C is to check the average head loss coefficient by installing the side benching in square manhole, based on shifted joining part model. The average head loss coefficient for circular and square manhole on case A was 1.6. This did not show much difference of the head loss coefficients in spite of the discharge variation in this case. However, case B and C show large difference between head loss coefficients due to the strong oscillation of water surface and the horizontal swirl motion. The circular and square manholes in case B reduced the head loss by 30% and 6% than ones in case A, respectively. The average head loss coefficient for circular manhole in case B was 1.1. Case C reduced average loss coefficients of the square manhole in case A from 1.6 to 1.1. Accordingly, the circular manhole in case B and the square manhole in case C showed the effective way to reduce the head loss. These head loss coefficients could be available to apply to the urban sewer system with surcharged flow.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.29 no.8
• /
• pp.419-428
• /
• 2017

In this study, energy loss due to ventilation load in the dock system was analyzed through simulation. Also, flow generated in the dock system of the warehouse was measured using manufactured measuring devices. Numerical simulation was conducted by simulating the most common picking tasks by examining the actual working environment. Incompressible and unsteady turbulent flows were assumed, and the turbulence model was the k-e standard model. Proper grid was selected through grid dependency test. Measurement was conducted using Honeywell and Vaisala sensors, and flow and temperature inside the warehouse were measured and compared with simulation results to validate simulation. When comparing amount of loss occurring in two hours and amount of loss occurring in 15 minutes, docking time of the former was eight times longer but energy loss was 3.8 times lower. Ventilation load occurring during the initial period after opening docking system accounted for a large proportion of total ventilation load. Also, comparing the load when the dock was closed and the load when the truck was parked, ventilation load was significantly higher than load due to heat conduction from the wall. Therefore, in improving the docking system, it is effective to reduce the gap by improving compatibility of the docking system and truck, rather than wall material.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.430-431
• /
• 2011

Recently the power system consists of the more complicated structure, due to increase of power demands. In this circumstance, the congestion and loss capacity in transmission line is also increased. Accordingly, the investment planning of transmission system is required to reduce the congestion and loss of the transmission line. In study of the planning of domestic and international transmission expansion, the reliability of transmission planning and minimizing Investment cost is focused. However, the study has not been performed systematically in economic aspects. Typically, the congestion and loss costs have been individually calculated. It is not consider the mutual relationship between the congestion cost and the loss cost. This paper proposes a method to compute concurrently the congestion and loss costs. This purpose is to calculate the more exact value for economic assessment of the power system operation.

• Fashion & Textile Research Journal
• /
• v.11 no.6
• /
• pp.918-924
• /
• 2009

As the population of overweight and obese children is rising rapidly around the world, there are many researches on purchasing and wearing children's clothing and optimal sizes, but researches on obese children are still inadequate. This study was carried out on 192 obese children over 75% in BMI. The purpose of the study was to set up the optimal interval of sizing system using the loss function which would be a guide for obese children for selecting ready to wear of suitable size. Introducing a loss function, which reflects how much the purchasing desire changes according to the difference, we formulate the problem and suggest a procedure to determine the optimal standard sizes minimizing the loss. These results were as follows ; In size chart of top's, 4 sizes had been determined by a loss function, had covered more than 91.1% of all subjects. In size chart of bottom's, 5 sizes had been determined by a loss function, had covered more than 87.0% of all subjects.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.12
• /
• pp.2328-2339
• /
• 1994

The PBS(Partial Buffer Sharing) space priority mechanism is one of priority control methods which may improve the performance of a single server queueing system when mixed traffic with different performance requirements is applied to the system. This paper analyzes the cell loss behavior of PBS assuming loss sensitive traffic and delay sensitive traffic are applied to the system. To derive the successive cell loss probabilities. which are an important performance measure of realtime traffic, we develop a recursive algorithm. Performance results show the successive cell loss probabilities obtained by our method are lager than the probabilities derived from an independent cell loss assumption. These results may indicate the limitation of PBS for realtime traffic and the increase of the admissible load with the criterion of quality of service.

• Journal of Magnetics
• /
• v.20 no.2
• /
• pp.148-154
• /
• 2015

48-V ISG (Integrated Starter Generator) system has attracted attention to improve the fuel efficiency of ICE (Internal Combustion Engine) vehicle. One of the key components that significantly affects the cost and performance of the 48-V ISG system is the motor. In an ISG motor, the core and copper loss make the motor efficiency change because the motor has a broad driving operated range and more diverse driving modes compared with other motors. When designing an ISG motor, the selection of an electrical steel sheet is important, because the electrical steel sheet directly influences the efficiency of the motor. In this paper, the efficiency of the ISG motor, considering core loss and copper loss, is analyzed by testing different types of electrical steel sheets with respect to the driving speed range and mode. Using the results of a finite element method (FEM) analysis, a method to select the electrical steel sheet is proposed. This method considers the cost of the steel sheet and the efficiency according to driving mode frequency during the design process of the motor. A wound rotor synchronous machine (WRSM) was applied to the ISG motor in this study.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.20 no.41
• /
• pp.213-220
• /
• 1997

Process capability Indices compare the actual performance of manufacturing process to the desired performance. The relationship between the capability index Cpm and the expected squared error loss provides an intuitive interpretation of Cpm. By putting the loss in relative terms a user needs only to specify the target and the distance from the target at which the product would have zero worth, or alternatively, the loss at the specification limits. Confidence limits for the expected relative loss are discussed, and numerical illustration is given.

• Journal of Powder Materials
• /
• v.16 no.6
• /
• pp.424-430
• /
• 2009

Electromagnetic wave energies are consumed in the form of thermal energy, which is mainly caused by magnetic loss, dielectric loss and conductive loss. In this study, CNT was added to the nanocrystalline soft magnetic materials inducing a high magnetic loss, in order to improve the dielectric loss of the EM wave absorption sheet. Generally, the aspect ratio and the dispersion state of CNT can be changed by the pre-ball milling process, which affects the absorbing properties. After the various ball-milling processes, 1wt% of CNTs were mixed with the nanocrystalline $Fe_{73}Si_{16}B_7Nb_{3}Cu_1$ base powder, and then further processed to make EM absorption sheets. As a result, the addition of CNT to Fe-based nanocrystalline materials improved the absorption properties. However, the increase of ball-milling time for more than 1h was not desirable for the powder mixture, because the ballmilling caused the shortening of CNT length and the agglomeration of the CNT flakes.

• Proceedings of the KIEE Conference
• /
• 2005.11b
• /
• pp.139-141
• /
• 2005

For the reliable evaluation of the distribution and power transformer no-load loss measurement, measurement uncertainty of the transformer measuring system, consisted of current transformer, potential transformer and power metering equipment is required. In this paper, we describe the uncertainty of transformer measuring system based on ANSI/IEEE C57.12.90.