• 한국염색가공학회지
• /
• 제24권4호
• /
• pp.281-287
• /
• 2012

Poly(phenylene sulfide) films containing acetophenone as a photoinitiator were photocrosslinked under UV irradiation using a continuous UV irradiator. The gel fraction of the irradiated PPS in 1-Chloro naphthalene reached 94.7% with increasing UV energy and the photoinitiator concentration in the film upto $200J/cm^2$ and 12wt% respectively. Solid state $^1C$ NMR analysis suggested that the crosslinking occurred between the phenylene chains in PPS, indicating that the acetophenone may the phenylene hydrogens and subsequently adjacent polymer radicals could be recombined to form the crosslinked structure. The crosslinking improved the thermal behavior of PPS such as loss of $T_g$ and $T_c$, higher melting point and lower melting enthalphy as well as significantly higher peak pyrolysis temperature as much as $63.5^{\circ}C$. Surprisingly the tensile toughness of the most crosslinked PPS increased by 842%, resulting from the substantial enhancements in tensile modulus, strength and strain as much as 76%, 236% and 240% respectively. Also dynamic mechanical measurement indicated that the distance between crosslinks in the crosslinked PPS reached 85.3 g/mol corresponing to a crosslink density of 0.012 mol/g.

• 한국전기전자재료학회논문지
• /
• 제11권5호
• /
• pp.394-399
• /
• 1998

High power characteristics with vibration velocity were studied in $Pb(Y_{2/3}W_{1/3})O_3-Pb(Zr,Ti)O_3$(PYW-PZT) ceramics by using the constant current method. Young s modulus $Y_0^E$ and mechanical quality factor $Q_m$ are a function of the square of effective vibration velocity \upsilon_0$. The nonlinear proportional constants of the above functions indicate the degree of stability under the vibration level change. The stability of PYW-PZT ceramics estimated by these constants coincides with the results obtained through the heat generation. It was found that $Q_m$ was markedly decreased with increasing the vibration velocity, accompanying a lot of heat generation. The vibration hysteresis and dielectric loss according to the vibration velocity was reduced by doping $Fe_2O_3$to the ceramics. On the contrary, these losses was increased by doping $Nb_2O_5$.

• Steel and Composite Structures
• /
• 제30권2호
• /
• pp.123-140
• /
• 2019

This paper presents experimental study on effects of width-to-thickness ratio and loading history on cyclic rotational capacity of H-shaped steel beams subjected to pure bending. Eight Class 3 and 4 H-shaped beams with large width-to-thickness ratios were tested under four different loading histories. The coupling effect of local buckling and cracking on cyclic rotational capacity of the specimens was investigated. It was found that loss of the load-carrying capacity was mainly induced by local buckling, and ductile cracking was a secondary factor. The width-to-thickness ratio plays a dominant effect on the cyclic rotational capacity, and the loading history also plays an important role. The cyclic rotational capacity can decrease significantly due to premature elasto-plastic local buckling induced by a number of preceding plastic reversals with relative small strain amplitudes. This result is mainly correlated with the decreasing tangent modulus of the structural steel under cyclic plastic loading. In addition, a theoretical approach to evaluate the cyclic rotational capacity of H-shaped beams with different width-to-thickness ratios was also proposed, which compares well with the experimental results.

• 대한건축학회논문집:구조계
• /
• 제36권2호
• /
• pp.127-136
• /
• 2020

Prism compressive strength is the most influential parameter to evaluate the seismic performance of non-structural concrete brick masonry walls, and is affected by the practice and workmanship of masonry workers. This study experimentally investigates the influence of workmanship on prism compressive strength throughout the compressive test with prism specimens constructed according to masonry workmanship. To do this, the workmanship is categorized into good, fair, and poor conditions which are statistically evaluated with thickness and indentation depth of bed-joints. Then, the effect of workmanship on the structural properties of masonry prisms is evaluated by investigating relations between properties such as their compressive strength, elastic modulus and numerical parameters such as thickness, filling of bed-joints. This study demonstrates that the indentation depth is more important parameter for structural properties of masonry prisms and masonry prisms with loss in bed-joint area less than of 7% can be in fair condition.

• Journal of the Korean Wood Science and Technology
• /
• 제32권6호
• /
• pp.67-73
• /
• 2004

The influence of liquefied wood (LW) on the mechanical and thermal properties of liquefied wood-polymer composites (LWPC) was investigated in this study. The thermal behaviors of LWPC were characterized by means of thermogravimetric (TGA) and differential scanning calorimetric (DSC) analyses. LW showed significant effects on the mechanical strength properties. The increase of flexural MOE and Young's modulus was related to the increase of stiffness of LWPC. The effect of LW was also significant on the flexural and tensile MOR. The impact strength decreased with the increase of LW application level. With the increased stress concentration by the poor bonding between LW and polymer, the impact strength of LWPC decreased, compared with that of high-density polyethylene (HDPE). The thermal stability of LWPC decreased with the increase of LW content up to 40%. The melting temperature of HDPE decreased with the increase of LW loading level. Enthalpy of HDPE also decreased with the addition of LW. This study proves the thermal stability necessary for the consolidation of composition materials.

• Structural Engineering and Mechanics
• /
• 제87권2호
• /
• pp.173-189
• /
• 2023

For a given structural geometry, the stiffness and damping parameters of the soil and the dynamic response of the structure may change in the face of an equivalent linear soil behavior caused by a strong earthquake. Therefore, the influence of equivalent linear soil behavior on the impedance functions form and the seismic response of the soil-structure system has been investigated. Through the substructure method, the seismic response of the selected structure was obtained by an analytical formulation based on the dynamic equilibrium of the soil-structure system modeled by an analog model with three degrees of freedom. Also, the dynamic response of the soil-structure system for a nonlinear soil behavior and for the two types of impedance function forms was also analyzed by 2D finite element modeling using ABAQUS software. The numerical results were compared with those of the analytical solution. After the investigation, the effect of soil nonlinearity clearly showed the critical role of soil stiffness loss under strong shaking, which is more complex than the linear elastic soil behavior, where the energy dissipation depends on the seismic motion amplitude and its frequency, the impedance function types, the shear modulus reduction and the damping increase. Excellent agreement between finite element analysis and analytical results has been obtained due to the reasonable representation of the model.

• Computers and Concrete
• /
• 제33권3호
• /
• pp.309-324
• /
• 2024

Internal curing, a widely used method for mitigating early-age shrinkage in concrete, also offers notable advantages for concrete durability. This paper explores the potential of internal curing by partial replacement of sand with fine lightweight aggregate for enhancing the behavior of high-performance concrete at elevated temperatures. Such a technique may prove economical and safe for the construction of skyscrapers, where explosive spalling of high-performance concrete in fire is a potential hazard. To reach this aim, the physico-mechanical features of internally cured high-strength concrete specimens, including mass loss, compressive strength, strain at peak stress, modulus of elasticity, stress-strain curve, toughness, and flexural strength, were investigated under different temperature exposures; and to predict some of these mechanical properties, a number of equations were proposed. Based on the experimental results, an advanced stress-strain model was proposed for internally cured high-performance concrete at different temperature levels, the results of which agreed well with the test data. It was observed that the replacement of 10% of sand with pre-wetted fine lightweight expanded clay aggregate (LECA) not only did not reduce the compressive strength at ambient temperature, but also prevented explosive spalling and could retain 20% of its ambient compressive strength after heating up to 800℃. It was then concluded that internal curing is an excellent method to enhance the performance of high-strength concrete at elevated temperatures.

• 한국건설순환자원학회논문집
• /
• 제7권4호
• /
• pp.438-444
• /
• 2019

본 연구에서는 모르타르의 동결융해피해에 미치는 폴리프로필렌섬유의 영향을 실험적으로 검토하였다. 섬유를 혼입하지 않은 섬유무보강 모르타르와 폴리비닐알코올섬유를 혼입한 모르타르를 비교 대상으로 하여 폴리프로필렌섬유의 혼입이 300사이클의 동결융해시험 후 모르타르의 압축 및 휨특성에 미치는 영향을 평가하였다. 또한, 300사이클의 동결융해 시험 후 모르타르의 질량감소율, 상대동탄성계수 및 공극크기분포에 대한 시험을 실시하였다. 그 결과, 섬유종류에 관계없이 섬유무혼입 모르타르에 비해 섬유혼입 모르타르는 300사이클의 동결융해시험 후 압축강도 및 휨강도의 역학적 성능저하와 질량감소율의 증가를 억제하는 것이 가능했다. 한편, 300사이클의 동결융해시험 후 모르타르의 공극감소에 대한 저항에 폴리비닐알코올섬유뿐만 아니라 폴리프로필렌섬유가 효과적으로 작용할 수 있는 것을 확인했으나 폴리프로필렌섬유를 혼입한 모르타르의 동결융해저항성을 향상시키기 위해서는 폴리비닐알코올섬유에서 기대할 수 있는 시멘트매트릭스와의 결합효율을 증가시킬 필요가 있다.

• 공업화학
• /
• 제26권3호
• /
• pp.336-340
• /
• 2015

단량체로 디페닐카보네이트를 이용한 세 종류의 폴리카보네이트(PC)/그래핀 옥사이드(GO) 복합체, 즉 이축압출기를 이용한 PC/GO 복합체(PC/GO), 촉매를 이용한 in-situ PC/GO 복합체(PC/GO-cat.), 그리고 -COCl로 표면 처리된 GO-COCl을 이용한 in-situ PC/GO 복합체(PC/GO-COCl)를 용융중합을 통해 제조하였다. PC/GO 복합체의 합성은 $3000cm^{-1}$와 $1750cm^{-1}$ 근처에서 나타나는 C-H 그리고 C=O 신축진동 피크를 통해 확인하였다. DSC와 TGA 분석 결과에 따르면, PC/GO와 PC/GO-cat.과 비교할 때, PC/GO-COCl의 유리전이온도가 상대적으로 낮은 값을 나타내었고, PC/GO 복합체의 열안정성이 가장 우세함을 나타내었다. 저장탄성률(G')-손실탄성률(G") 그래프의 기울기는 고분자 용융체의 비균질성의 증가와 함께 감소하는 경향이 있어, GO 분산성을 확인하는데 사용될 수 있다. G'-G" 기울기 결과로부터 PC/GO와 PC/GO-cat. 복합체의 PC 매트릭스 내 GO 분산성이 양호함을 알 수 있고, 이는 원자력현미경 사진을 통해 재확인하였다. PC/GO-COCl의 경우 분산성이 열세한 이유 중 하나는 중합과정에서 -COCl에 의해 분지구조나 가교구조 등이 발생하여 GO의 분산을 방해하기 때문으로 해석할 수 있고, 이는 복합탄성률과 위상차(${\delta}$) 그래프로부터 확인할 수 있었다.

• 한국식품영양과학회지
• /
• 제44권9호
• /
• pp.1407-1413
• /
• 2015

본 연구는 '고운' 품종으로 제조한 감자가루 분산액의 농도(3, 4, 5, 6, 7%, w/w)에 따른 유변학적 및 페이스팅 특성에 대하여 평가하였다. 감자가루 분산액은 전단담화 거동(n=0.41~0.55)을 나타냈으며, 감자가루 농도가 증가함에 따라 점조도 지수(n), 겉보기 점도(${\eta}_{a,100}$), Casson 항복응력(${\sigma}_{oc}$)값이 증가하는 경향을 나타내었다. 또한 동적 점탄 특성 측정 결과에 의하면 감자가루 분산액은 약한 겔과 같은 거동을 보여주었으며 G'과 G" 값들은 감자가루 농도와 진동수(${\omega}$)가 증가함에 따라 증가하는 경향을 나타내었다. Cox-Merz 중첩원리는 감자가루 분산액에 잘 적용되지 않았다. RVA에 의한 페이스팅 특성은 감자가루 농도가 증가할수록 peak viscosity, trough viscosity, final viscosity, set back viscosity, break down viscosity 값이 유의적으로 증가하였다.