• Structural Engineering and Mechanics
• /
• 제67권2호
• /
• pp.131-142
• /
• 2018

The perfobond connector, composed of a steel plate with a number of holes, serves as a certain type of shear connector in steel and concrete composite structures. Depending on limits in hole distances and rib heights, various hole shapes including circular-hole and long-hole are alternatives for perfobond connectors. This study presented the results of tests performed on 72 push-out specimens with perfobond connectors. The purpose was to evaluate the shear strength of perfobond connectors with circular-hole and long-hole. The effects of various parameters were investigated, including the hole diameter, the hole length, the hole height, the concrete strength, the existence, diameter and strength of rebar in the hole, the thickness, height and distance of perfobond ribs, and the thickness of concrete slabs. On the basis of 132 push-out test results in references and in this study, an analytical model was proposed by regression analysis to predict the shear strength of perfobond connectors. The proposed equation agreed reasonably well with the experimental results of perfobond connectors with different hole shapes.

• 화약ㆍ발파
• /
• 제32권3호
• /
• pp.10-17
• /
• 2014

본 연구에서는 2자유면을 가진 암반의 장공발파 시 천공간격과 뇌관의 기폭시차에 따라 발생되는 내부주변형률의 변화를 확인하기 위하여 Visual FEA 유한요소 프로그램으로 해석 암반의 단면을 모델링하여 인접공균열권 내의 주요 절점에서 최대주변형률을 분석하였다. 결과적으로, 장공발파 시 천공간격이 좁고 기폭시차가 길수록 인접공 균열권 내에 미치는 최대주변형률 값이 크게 나타났고, 장약장 내 폭약의 기폭 위치에 따라 최대 주변형률의 차이를 보였다.

• Applied Science and Convergence Technology
• /
• 제25권2호
• /
• pp.42-45
• /
• 2016

A two-dimensional metal hole array (2DMHA) structure is fabricated by conventional photo-lithography and electron beam evaporation. The transmittance of the 2DMHA is measured at long wave infrared (LWIR) wavelengths (${\lambda}{\sim}10$ to $24{\mu}m$). The 2DMHA sample shows transmittance of 70 and 67% at $15.4{\mu}m$ due to plasmonic resonance with perforated silver and gold thin films, respectively, under surface normal illumination at LWIR wavelengths. The measured infrared spectrum is separated into two peaks when the size of the hole becomes larger than a half-pitch of the hole array. Six degenerated plasmon modes (1,0) at the metal/Si surface split to three modes at an incident beam angle of $45^{\circ}$ with respect to the surface normal direction, and wavelength shifts of the transmitted spectrum are observed in a red shift and blue shift at the same time.

• 화약ㆍ발파
• /
• 제31권2호
• /
• pp.32-39
• /
• 2013

일반적으로 장공발파 방법은 과거 대규모 채탄막장이나 댐 기초굴착, 광산 등에서 행하여져 왔으나, 최근 우리나라에서 신설되는 토목터널에서 시공 효율성 및 경제성을 목적으로 많이 실시되고 있다. 고속국도제 600호선 부산외곽 고속도로 ${\bigcirc}$공구 또한 총연장 약 8km의 4차선 대단면 도로 터널로서 Type I, II, 4.4m 장공발파를 실시하는 현장이다. 그러나 당 현장에서는 발파 후 굴진율이 약 75%에 그쳐 발파 후속작업 시간에 영향을 미치게 되고 그로 인하여 전체 작업공정 시간이 증가하여 계획된 굴진을 못하는 현상이 자주 발생되었다. 본 논문에서는 당 현장에서 위 문제를 극복하기 위하여 실시된 장공발파 공법 중 천공경과 가장 밀장전 할 수 있는 ${\phi}36mm$폭약을 적용하여 굴진효율을 향상시키고 작업공정 시간을 단축시킨 사례를 소개하고자 한다.

• 천문학회지
• /
• 제28권1호
• /
• pp.71-75
• /
• 1995

In the previous work we made a long term evolution code for the central black hole in an active galactic nucleus under the assumption that the Blandford-Znajek process is the source of the emission. Using our code we get the evolution of the angular velocity of the precession for a supermassive black hole. We consider a hole at the center of an axisymmetric, ellipsoidal galactic nucleus. Our numerical results show that, only for the cases such that the stellar density or the mass of the black hole is large enough, the precession of the black hole - presumably the precession of the galactic jet - is interestingly large.

• 한국분무공학회지
• /
• 제26권4호
• /
• pp.197-203
• /
• 2021

In gasoline direct injection injectors, cavitation can be generated inside the hole because of their high injection pressure. In this paper, the effects of cavitation development in injector were investigated depending on the various hole drilling angles were investigated by a numerical method. In order to verify the internal flow model, injection rate and injection quantity of individual holes were measured. The BOSCH long tube method was used to measure the injection rate. As a result, even if the hole diameters were the same, the discharge coefficient differed by up to 10% depending on the hole angle. Moreover, if the hole drilling angle became greater than 30°, the area coefficient and the discharge coefficient decreased as the nozzle outlet was blocked due to cavitation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.311-312
• /
• 2010

The fabricated photovoltaic cells based on PIN heterojunctions, in this study, have a structure of ITO/poly(3, 4-ethylenedioxythiophene)-poly(styrenesulfonate)(PEDOT:PSS)/donor/donor:C60(10nm)/C60(35nm)/2, 9-dimethyl-4, 7-diphenyl-1, 10-phenanthroline(8nm)/Al(100nm). The thicknesses of an active layer(donor:C60), an electron transport layer(C60), and hole/exciton blocking layer(BCP) were fixed in the organic photovoltaic cells. We investigated the performance characteristics of the PIN organic photovoltaic cells with copper phthalocyanine(CuPc), tetracene and pentacene as a hole transport layer. Discussion on the photovoltaic cells with CuPc, tetracene and pentacene as a hole transport layer is focussed on the dependency of the power conversion efficiency on the deposition rate and thickness of hole transport layer. The device performance characteristics are elucidated from open-circuit-voltage(Voc), short-circuit-current(Jsc), fill factor(FF), and power conversion efficiency($\eta$). As the deposition rate of donor is reduced, the power conversion efficiency is enhanced by increased short-circuit-current(Jsc). The CuPc-based PIN photovoltaic cell has the limited dependency of power conversion efficiency on the thickness of hole transport layer because of relatively short exciton diffusion length. The photovoltaic cell using tetracene as a hole transport layer, which has relatively long diffusion length, has low efficiency. The maximum power conversion efficiencies of CuPc, tetracene, and pentacene-based photovoltaic cells with optimized deposition rate and thickness of hole transport layer have been achieved to 1.63%, 1.33% and 2.15%, respectively. The photovoltaic cell using pentacene as a hole transport layer showed the highest efficiency because of dramatically enhanced Jsc due to long diffusion length and strong thickness dependence.

• The Journal of Korean Physical Therapy
• /
• 제24권2호
• /
• pp.151-156
• /
• 2012

Purpose: The purpose of this study was to investigate the adverse effects of sensorimotor function at the shoulder joint according to long-term cane usage in stroke patients without apraxic behavior, in terms of the presence of shoulder joint pain, accuracy of tracking task, proprioceptive joint position sense, and nine-hole pegboard. Methods: Nineteen stroke patients with long-term cane usage (cane usage group) and nineteen stroke patients without cane usage (non-cane usage group) were recruited. All subjects were tested in pain presence, a tracking task for visuomotor function, joint reposition, and nine-hole pegboard in the shoulder joint regarding the non-affected side. Results: In the accuracy index for tracking task and the nine-hole pegboard test, significant differences were observed between the cane usage group and the non-cane usage group. However, although a higher emergence of shoulder pain and a lower accuracy for joint reposition sense were detected in the cane usage group in comparison to the non-cane usage group, there were no significant differences between the two groups. Conclusion: Our findings suggest that long-term cane usage could induce to decrease in delicate movement and coordination in the non-affected upper arm in stroke patients. In addition, they could experience high frequency of shoulder pain and poor joint reposition sense. Therefore, careful evaluation and observation will be required concerning stroke patients with long-term cane usage.

• 대한수학회지
• /
• 제42권6호
• /
• pp.1251-1264
• /
• 2005

Let D be an acyclic digraph. The competition graph of D has the same set of vertices as D and an edge between vertices u and v if and only if there is a vertex x in D such that (u, x) and (v, x) are arcs of D. The competition number of a graph G, denoted by k(G), is the smallest number k such that G together with k isolated vertices is the competition graph of an acyclic digraph. It is known to be difficult to compute the competition number of a graph in general. Even characterizing the graphs with competition number one looks hard. In this paper, we continue the work done by Cho and Kim[3] to characterize the graphs with one hole and competition number one. We give a sufficient condition for a graph with one hole to have competition number one. This generates a huge class of graphs with one hole and competition number one. Then we completely characterize the graphs with one hole and competition number one that do not have a vertex adjacent to all the vertices of the hole. Also we show that deleting pendant vertices from a connected graph does not change the competition number of the original graph as long as the resulting graph is not trivial, and this allows us to construct infinitely many graph having the same competition number. Finally we pose an interesting open problem.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.90-90
• /
• 2012

The electron/hole injections in organic electronic devices have long been an issue due to the large energy level mismatches between electrode and organic layer. To utilize the organic materials in electronic devices, functional thin layers have been used, which reduce the electron/hole injection barrier from electrode to organic material. Typically, inorganic compounds and organic molecules are used as an electron and hole injection layer, respectively. Recently, CsN3 and 1,4,5,8,- naphthalene-tetracarboxylic-dianhydride (NTCDA) are reported as a potential electron and hole injection layers. CsN3 shows unique properties that it breaks into Cs and N and thus Cs can dope organic layer into n-type. On the other side, hole injection anode, NTCDA forms gap states with anode material. In this presentation, we show the electronic structure changes upon the insertion of CsN3 and NTCDA at proper interfaces to reduce the charge injection barriers. These barrier reductions are correlated with device characteristics.