• 한국산학기술학회논문지
• /
• 제19권11호
• /
• pp.604-613
• /
• 2018

전 세계적으로 철도의 노후화 및 고속화 등으로 인한 열차탈선사고가 증가하고 있으며, 그로인한 인적 물적 피해가 증가하고 있는 실정이다. 특히 철도교량의 경우에는 가드레일 또는 방호벽 등을 설치하고 있으나, 이는 탈선열차차량(train body level)이 방호벽과 충돌함으로써 열차의 탈선운동을 억제하여 정지시키는데 목적이 있다. 이와 같은 차량에 의한 탈선방호는 인명피해 위험성 및 2차 피해발생 가능성이 높다. 그러므로 본 연구에서는 주행레일 사이에 일탈방호시설물(DCP, Derailment Containment Provision)을 설치하여, 차륜 또는 차축(wheel/bogie level)에서 탈선열차를 방호할 수 있는 시설물을 개발하였다. 또한, 기존 철도교량의 일탈방호성능을 확보할 수 있도록 DCP의 급속시공이 가능하도록 설계하였으며, 방호벽에 작용하는 충돌하중과 급곡선부에서의 관성력을 감소시킴으로써 일탈된 열차가 교량 밖으로의 전도 낙하방지 및 반대편 선로의 침입하는 것을 최소화 하고자 하였다. 본 논문에서는 LS-Dyna을 이용하여, 설계한 DCP의 열차 충돌위치 및 콘크리트 궤도 접합조건에 따른 거동에 대하여 해석적으로 변수연구를 수행하였다. 특히 접합조건은 접합재료의 물성치에 따라 끊어짐을 모사하는 Tiebreak contact과 완전 부착되었다고 가정하는 Perfect bond contact으로 나눠 해석적으로 검토하였다. DCP의 변위, 앵커 및 콘크리트의 응력, 변형률을 확인한 결과 Tiebreak contact이 실제 충돌하중에 대한 거동을 보다 유사하게 모사하는 것으로 판단하였다. 또한, 충돌위치에 따른 변위는 접합구간에서 가장 큰 변형이 발생하였으며, DCP 블록의 중앙에 충돌이 가해질 경우, 충돌하중이 가해지는 DCP 배면에서 휨 파괴가 발생하였다. 본 연구에서 수행한 충돌해석은 실제 충돌실험의 어려움에 의해 사전적으로 해석을 수행하였으며, 이를 바탕으로 DCP 앵커 설계변경은 필요할 것으로 판단된다.

• Geomechanics and Engineering
• /
• 제18권1호
• /
• pp.71-83
• /
• 2019

This investigation presented conventional triaxial and creep-permeability tests on sandstones considering thermally-induced damage (TID). The TID had no visible effects on rock surface color, effective porosity and permeability below $300^{\circ}C$ TID level. The permeability enlarged approximately two orders of magnitude as TID increased to $1000^{\circ}C$ level. TID of $700^{\circ}C$ level was a threshold where the influence of TID on the normalized mass and volume of the specimen can be divided into two linear phases. Moreover, no prominent variations in the deformation moduli and peak strength and strain appeared as TID< $500^{\circ}C$ level. It is interesting that the peak strength increased by 24.3% at $700^{\circ}C$ level but decreased by 11.5% at $1000^{\circ}C$ level. The time-related deformation and steady-state creep rate had positive correlations with creep loading and the TID level, whereas the instantaneous modulus showed the opposite. The strain rates under creep failure stresses raised 1-4 orders of magnitude than those at low-stress levels. The permeability was not only dependent on the TID level but also dependent on creep deformation. The TID resulted in large deformation and complexity of failure pattern for the sandstone.

• Structural Engineering and Mechanics
• /
• 제6권7호
• /
• pp.827-839
• /
• 1998

This paper presents a study of buckling of the multi-vaulted cylindrical shell ("Aster"), under an axial compression alone or combined with an external pressure. This shell which was presented in a recent paper is a self-stiffened structure having a satisfactory behaviour and a higher buckling strength under external pressure than a circular cylindrical shell with the same dimensions. The results of this study emphasize the interest of the behaviour of the "Aster" shell under two other types of loading, revealing an acceptable level of strength which is favorable for an expansion of its use in other areas.

• Structural Engineering and Mechanics
• /
• 제11권3호
• /
• pp.259-272
• /
• 2001

The impact behavior of a multigirder concrete bridge under single and multiple moving vehicles is studied based on correlated road surface characteristics. The bridge structure is modeled as grillage beam system. A 3D nonlinear vehicle model with eleven degrees of freedom is utilized according to the HS20-44 truck design loading in the American Association of State Highway and Transportation Officials (AASHTO) specifications. A triangle correlation model is introduced to generate four classes of longitudinal road surface roughness as multi-correlated random processes along deck transverse direction. On the basis of a correlation length of approximately half the bridge width, the upper limits of impact factors obtained under confidence level of 95 percent and side-by-side three-truck loading provide probability-based evidence for the evaluation of AASHTO specifications. The analytical results indicate that a better transverse correlation among road surface roughness generally leads to slightly higher impact factors. Suggestions are made for the routine maintenance of this type of highway bridges.

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2007년도 정기총회 및 학술발표대회
• /
• pp.546-550
• /
• 2007

High excess pore water pressure may develop when loose saturated sand is subjected to earthquake excitation, resulting in reduction in the shear strength and stiffness, and ultimately can result in liquefaction. It is very important to accurately assess the level of the pore pressure generation for seismic design and to perform effective stress analysis. A simple numerical 모형 is developed for estimating the development of pore water pressure due to seismic loading. The method only uses two parameters and the length of the accumulated shear strain. The accuracy of the proposed 모형 is verified through a series of laboratory test data. Comparisons show that the modified 모형 is an improvement over existing 모형s.

• 한국안전학회지
• /
• 제16권1호
• /
• pp.73-78
• /
• 2001

It has been proposed that the acceptable level of discomfort was a valid measure of postural loading. Although the number of women employees has increased at a much faster rate than men workers did and female workers are thought to be more vulnerable to musculoskeletal disorders, most previous studies dealt with perceived discomforts for joint motions focused on male subjects. This study aims to measure perceived discomfort ratings of females for static joint motions. Ten female subjects participated in the experiment measuring perceived discomforts, in which almost every possible joint motion was included and the free modulus method of the magnitude estimation was employed. The results showed that discomfort levels were dependent on the joint motions and joints, and subjective discomfort ratings of women were significantly larger than those of men.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1998년도 유체기계 연구개발 발표회 논문집
• /
• pp.91-96
• /
• 1998

The broadband noise generated aerodynamically from a two-bladed axial flow fan has been measured and compared to the result of a self-noise prediction method. The prediction scheme is based on the experimental data set acquired from a series of aerodynamic and acoustic tests of two and three-dimensional airfoil blade sections. For low blade loading case the comparison showed a reasonably good agreement, but as the loading becomes larger the empirical formula overpredict the sound pressure level at high frequency range. This is probably due to the use of stationary wing data for the prediction of rotating blade case, which will be quite different in their vortex strength at the blade tip.

• Steel and Composite Structures
• /
• 제9권1호
• /
• pp.19-38
• /
• 2009

The present paper provides test data to evaluate the seismic performance of recycled aggregate concrete (RAC) filled steel square hollow section (SHS) beam-columns. Fifteen specimens, including 12 RAC filled steel tubular (RACFST) columns and 3 reference conventional concrete filled steel tubular (CFST) columns, were tested under reversed cyclic flexural loading while subjected to constant axially compressive load. The test parameters include: (1) axial load level (n), from 0.05 to 0.47; and (2) recycled coarse aggregate replacement ratio (r), from 0 to 50%. It was found that, generally, the seismic performance of RACFST columns was similar to that of the reference conventional CFST columns, and RACFST columns exhibited high levels of bearing capacity and ductility. Comparisons are made with predicted RACFST beam-column bearing capacities and flexural stiffness using current design codes. A theoretical model for conventional CFST beam-columns is employed in this paper for square RACFST beam-columns. The predicted load versus deformation hysteretic curves are found to exhibit satisfactory agreement with test results.

• 한국재료학회지
• /
• 제12권2호
• /
• pp.135-139
• /
• 2002

Carbon powders (CP) and carbon fiber (CF) were introduced info glass fiber reinforced plastics (FRP) composites to obtain fracture detection function. The composites were evaluated through the relation between a load-displacement curve and an electrical resistance change curve in three point bending test. CP containing FRP (CP-FRP) has a sensitivity of electrical resistance change at much lower load level than CF containing FRP (CF-FRP). In loading-unloading tests, CP-FRP showed a large amount of residual electrical resistance which enables the estimation of loading hysteresis.

• Structural Engineering and Mechanics
• /
• 제61권3호
• /
• pp.317-323
• /
• 2017

This work presents a new strategy to model stress dependent relaxation process in large deformation. The strategy is relied on the fact that in some particular soft materials undergoing large deformation, e.g., elastomers, rubbers and soft tissues, the relaxation time depends strongly on stress levels. To simplify the viscoelastic model, we consider that the relaxation time is the function of previous elastic deviatoric stress state experienced by materials during loading. Using the General Maxwell Model (GMM), we simulate numerically conditions with the constant and the stress dependent relaxation time for uniaxial tension and compression loading. Hence, it can be shown that the proposed model herein not only can represent different relaxation time for different stress level but also maintain the capability of the GMM to model hysteresis phenomena.