• 콘크리트학회논문집
• /
• 제13권6호
• /
• pp.568-574
• /
• 2001

콘크리트 시험편에 대한 삼점휨실험을 실시하여 여러 실험에 대해 측정된 반응의 평균값을 계산하곤 계산된 평균거동으로부터 삼점휨 시험편이 완전히 파손될 때까지 연속적으로 성장하는 균열에 대한 파괴거동이 분석되었다. 이 연구에서 사용된 실험변수는 25.4mm와 6.4mm의 초기균열길이 그리고 2000sec와 20sec의 실험기간이며, 초기균열길이는 파괴진행대(FPZ) 크기의 영향과 시험편의 기하학적 특성 및 경계조건에 대한 영향을 분석하기 위한 것이다. 실험기간은 초기 크리프(creep)의 영향을 위해 설정되었으나, 이 연구의 하중점-변위 속도에서는 심각한 영향이 관측되지 않았다. 여러 실험의 평균 외부일로부터 평균하중이 계산되었으며, 변형률 게이지를 사용하여 평균 균열길이를 측정하였다. 최대하중 이전의 저항곡선은 파괴진행대의 크기에 대해 유사한 값을 보였다. 그러나 최대하중 직후에는 초기균열의 크기에 관계없이 0.088~0.154mm의 하중점-변위에서 88mm의 불안정 균열성장이 발생되었으며, 평균 파괴에너지율 $G_{F}$$^{ave}$ = 115N/m은 이 불안정 균열성장 동안에 발생되었다. 균열길이 111mm에서 완전한 파괴진행대가 형성되었고, 25.4mm와 6.4mm의 초기균열길이에 대해 파괴진행대의 크기는 각각 86mm와 105mm이었다. 완전한 파괴진행대의 형성이후 저항곡선의 평균 파괴에너지율은 25.4mm와 6.4mm의 초기균열길이에 대해 각각 229N/m로 284N/m로 $G_{F}$$^{ave}$의 두 배 이상이었다.이었다.이었다.

• Steel and Composite Structures
• /
• 제37권2호
• /
• pp.117-136
• /
• 2020

Curved steel-concrete composite box girder has been widely adopted in urban overpasses and ramp bridges. In order to investigate its mechanical behavior under complicated and combined bending, shear and torsion load, two large-curvature composite box girders with interior angles of 25° and 45° were tested under static hogging moment. Based on the strain and deflection measurement on critical cross-sections during the static loading test, the failure mode, cracking behavior, load-displacement relationship, and strain distribution in the steel plate and rebar were investigated in detail. The test result showed the large-curvature composite box girders exhibited notable shear lag in the concrete slab and steel girder. Also, the constraint torsion and distortion effect caused the stress measured at the inner side of the composite beam to be notably higher than that of the outer side. The strain distribution in the steel web was approximately linear; therefore, the assumption that the plane section remains plane was approximately validated based on strain measurement at steel web. Furthermore, the full-process non-linear elaborate finite element (FE) models of the two specimens were developed based on commercial FE software MSC.MARC. The modeling scheme and constitutive model were illustrated in detail. Based on the comparison between the FE model and test results, the FE model effectively simulated the failure mode, the load-displacement curve, and the strain development of longitudinal rebar and steel girder with sufficient accuracy. The comparison between the FE model and the test result validated the accuracy of the developed FE model.

• 대한기계학회논문집A
• /
• 제36권1호
• /
• pp.17-28
• /
• 2012

본 연구에서는 역해석 방법을 통해, 중심각이 서로 다른 두 삼각뿔 압입자를 이용하는 재료물성 평가법을 제안한다. 자기유사성을 갖는 첨단형 압입자를 사용한 압입시험 전산모사시, 동일 압입깊이에 대해 원뿔형 및 삼각뿔 압입자가 주는 하중-변위 곡선들이 다름을 확인했다. 따라서 삼각뿔형 압입자를 이용한 물성평가는 원뿔형 압입자와 별도로 독립적인 연구가 필수적이다. 먼저 다양한 재료들에 대한 삼각뿔 압입 유한요소해석들로 얻은 하중-변위 곡선들의 특징을 살폈다. 이를 토대로 압입자 반각이 다른 두 삼각뿔 압입자를 이용해 유한요소해석으로 얻은 하중-변위곡선들의 회귀분석으로 재료물성치를 얻는 이중 삼각뿔 압입물성평가 알고리듬을 제시했다. 제안된 물성평가법을 이용하면 다양한 재료에 대해 평균오차 3% 이내로 영률 및 항복강도, 변형경화지수의 예측이 가능하다.

• Earthquakes and Structures
• /
• 제24권6호
• /
• pp.439-453
• /
• 2023

Older brick masonry structures generally suffer from low strength defects. Using a cement mortar layer (CML) or steel-meshed cement mortar layer (S-CML) to reinforce existing low-strength brick masonry structures (LBMs) is still an effective means of increasing seismic performance. However, performance indices such as lateral displacement ratios and skeleton curves for LBMs reinforced with CML or S-CML need to be clarified in performance-based seismic design and evaluation. Therefore, research into the failure mechanisms and seismic performance of LBMs reinforced with CML or S-CML is imperative. In this study, thirty low-strength brick walls (LBWs) with different cross-sectional areas, bonding mortar types, vertical loads, and CML/S-CML thicknesses were constructed. The failure modes, load-carrying capacities, energy dissipation capacity and lateral drift ratio limits in different limits states were acquired via quasi-static tests. The results show that 1) the primary failure modes of UBWs and RBWs are "diagonal shear failure" and "sliding failure through joints." 2) The acceptable drift ratios of Immediate Occupancy (IO), Life Safety (LS), and Collapse Prevention (CP) for UBWs can be 0.04%, 0.08%, and 0.3%, respectively. For 20-RBWs, the acceptable drift ratios of IO, LS, and CP for 20-RBWs can be 0.037%, 0.09%, and 0.41%, respectively. Moreover, the acceptable drift ratios of IO, LS, and CP for 40-RBWs can be 0.048%, 0.09%, and 0.53%, respectively. 3) Reinforcing low-strength brick walls with CML/S-CML can improve brick walls' bearing capacity, deformation, and energy dissipation capacity. Using CML/S-CML reinforcement to improve the seismic performance of old masonry houses is a feasible and practical choice.

• 한국재료학회지
• /
• 제14권9호
• /
• pp.649-654
• /
• 2004

In this paper, the fracture toughness and mechanisms of failure in a random SiC-whisker/$Al_{2}O_3$ ceramic composite were investigated using in situ observations during mode I(opening) loading. $SiC_{w}/Al_{2}O_3$ composite was obtained by hot press sintering of $Al_{2}O_3$ powder and SiC whisker as the matrix and reinforcement, respectively. The whisker and powder were mixed using a turbo mill. The composite was produced at SiC whisker volume fraction of $0.3\%$. Compared with monolithic $Al_{2}O_3$, fracture toughness enhancement was observed in $SiC_{w}/Al_{2}O_3$ composite. This improved fracture toughness was attributed to SiC whisker bridging and crack deflection. $SiC_{w}/Al_{2}O_3$ composite exhibited typically brittle fracture behavior, but a fracture process zone was observed in this composite. This means that the load versus load-line displacement curve of $SiC_{w}/Al_{2}O_3$ composite from a fracture test may involve a small non-linear region near the peak load.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.204-209
• /
• 2001

In this research, the effects of fiber stacking sequence on damage behaviors of FML(Fiber Metal Laminates) subject to indentation loading. SOP (Singly Oriented Ply) FML and angle ply FML were fabricated to study fiber orientation effects and angle ply effects. FML were fabricated by using 1050 aluminum laminate and carbon/epoxy prepreg. To increase adhesive bonding strength, Al laminate was etched using FPL methods. The static indentation test were conducted by using UTM(5ton, Shimadzu) under the 2side clamped conditions. During the tests, load and displacement curve and crack initiation and propagation behaviors were investigated. As fiber orientation angle increases, the crack initiation load of SOP FML increases because the stiffness induced by fiber orientation is increased. The penetration load of SOP FML is influenced by the deformation tendency and boundary conditions. However, the macro-crack of angle ply FML was initiated by fiber breakage of lower ply because angle plies in Angle ply FML prevents the crack growth and consolidation. The Angle ply FML has a critical cross-angle which prevent crack growth and consolidation. Damage behavior of Angle ply FML is changed around the critical cross-angle.

• Nuclear Engineering and Technology
• /
• 제45권1호
• /
• pp.89-98
• /
• 2013

In recent years steel-concrete composite shear walls have been widely used in enormous high-rise buildings. Due to high strength and ductility, enhanced stiffness, stable cycle characteristics and large energy absorption, such walls can be adopted in the auxiliary building; surrounding the reactor containment structure of nuclear power plants to resist lateral forces induced by heavy winds and severe earthquakes. This paper demonstrates a set of nonlinear numerical studies on I-shaped composite steel-concrete shear walls of the nuclear power plants subjected to reverse cyclic loading. A three-dimensional finite element model is developed using ABAQUS by emphasizing on constitutive material modeling and element type to represent the real physical behavior of complex shear wall structures. The analysis escalates with parametric variation in steel thickness sandwiching the stipulated amount of concrete panels. Modeling details of structural components, contact conditions between steel and concrete, associated boundary conditions and constitutive relationships for the cyclic loading are explained. Later, the load versus displacement curves, peak load and ultimate strength values, hysteretic characteristics and deflection profiles are verified with experimental data. The convergence of the numerical outcomes has been discussed to conclude the remarks.

• 한국지반공학회논문집
• /
• 제36권3호
• /
• pp.25-36
• /
• 2020

동토의 세립분 함유량에 따른 파괴특성을 파악하기 위해 -10℃의 온도에서 다양한 세립분 함유량과 초기 노치(notch)의 위치를 조정한 직사각형 공시체를 제작하여 Three-point bending 시험을 수행하였다. 시험결과를 바탕으로 동토의 mode I 파괴인성(fracture toughness)을 산정하였으며, 하중-변형 곡선의 최대점까지의 fracture energy를 산정하여 동토의 mixed-mode(mode I + II) 파괴특성을 파악하였다. 시험결과, 최대하중 및 mode I 파괴인성은 세립분 함유량 10%까지 증가하다가 15%에서 다시 감소하는 경향을 나타내었다. 또한, 노치의 위치가 공시체 중심에서 멀어질수록 mode II 하중의 증가로 인해 균열이 진행하는데 필요한 fracture enenrgy가 증가하는 것으로 나타났으며, 세립분 함유량이 증가할수록 mode II 하중의 증가비율 또한 증가하는 것으로 나타났다.

• 한국산학기술학회논문지
• /
• 제16권5호
• /
• pp.3596-3601
• /
• 2015

진동해머에 의해 시공되는 말뚝의 거동을 분석할 목적으로 개발된 기존의 프로그램을 개선하고자 하였다. 진동해머-말뚝-지반으로 구성되는 진동시스템의 기존 지배방정식에 지반저항의 댐핑효과와 클러치마찰력을 추가하였다. 또한, 개발된 해석기법의 하중전이곡선을 모사하는 수정 Ramberg-Osgood 모델의 매개변수를 재산정하여 해석기법을 개선하고자 하였다. 수정된 프로그램에 의한 해석결과를 현장시험결과와 비교해 볼 때 시간에 따른 말뚝의 변위 및 하중전이거동이 현장시험결과에 좀 더 유사하였다. 개발된 프로그램에 의한 말뚝 관입깊이별 관입속도를 상용 프로그램에 의한 결과 및 현장시험결과와 비교해 볼 때 상용프로그램보다 훨씬 더 현장시험결과에 가까웠다.

• Steel and Composite Structures
• /
• 제25권6호
• /
• pp.705-716
• /
• 2017

The objective of this study is to investigate the actual behavior of studs in structures under earthquake load through laboratory tests and numerical simulation. A test program including eighteen specimens was devised with consideration of different concrete strengths and stud diameters. Six of specimens were subjected to monotonically increasing loading while the others were subjected to cyclic loading. Mechanical behavior including the failure mechanism, load-slip relationship, stiffness degradation, energy dissipation and the damage accumulation was obtained from the test results. An accurate numerical model based on the ABAQUS software was developed and validated against the test results. The results obtained from the finite element (FE) model matched well with the experimental results. Furthermore, based on the experimental and numerical data, the design formulas for expressing the skeleton curve were proposed and the simplified hysteretic model of load versus displacement was then established. It is demonstrated that the proposed formulas and simplified hysteretic model have a good match with the test results.