• The Journal of Engineering Geology
• /
• v.14 no.2
• /
• pp.199-210
• /
• 2004

In this study, the physical and mechanical properties of the weathered shale soils distributed in the Hwasun area have been measured in the laboratory. The physical and mechanical properties of the weathered shale soils in the study area as follows: the specific gravity is 2.66 to 2.68, the liquid limit is 36.39 to 36.92(%), the plastic limit is 18.53 to 19.48(%), the plasticity index is 17.44 to 17.86 and soil classification is CL. The maximum dry unit weight and optimum moisture content as calculated by compaction test is 22.5 to 23% and 1.58 to $1.61t/\textrm{m}^3$, respectively. The result of direct shear testing show that cohesion in saturated and unsaturated conditions increases according to the increase of dry unit weight. Internal friction angle in an unsaturated condition increases with an increase of dry unit weight, but in a saturated condition, it increases after decreasing. When compares with engineering characteristics of tile weathered shale soils in the Daegu area (Kim et al., 1995), specific gravity is found to be similar, but the liquid and plastic limit of soil samples in this study area is slightly higher than those of soil samples in the Daegu area.

• Journal of Powder Materials
• /
• v.27 no.6
• /
• pp.468-476
• /
• 2020

The bone cement used for vertebroplasty must be sufficiently injectable. The introduction of granules reduces the amount of liquid required for liquefaction, implying that higher fluidity is achieved with the same amount of liquid. By employing β-tricalcium phosphate granules with an average diameter of 50 ㎛, changes in injectability are observed based on the paste preparation route and granular fraction. To obtain acceptable injectability, phase separation must be suppressed during injection, and sufficient capillary pressure to combine powder and liquid must work evenly throughout the paste. To achieve this, the granules should be evenly distributed. Reduced injection rates are observed for dry mixing and excessive granular content, owing to phase separation. All these correspond to conditions under which the clustered granules weakened the capillary pressure. The injected ratio of the paste formed by wet mixing displayed an inverted U-type shift with the granular fraction. The mixture of granules and powder resulted in an increase in the solid volume fraction, and a decrease in the liquid limit. This resulted in the enhancement of the liquidity, owing to the added liquid. It is inferred that the addition of granules improves the injectability, provided that the capillary pressure in the paste is maintained.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.68-79
• /
• 2018

An examination of the characteristics of the ground material in is very important in a ground investigation. Casagrande classified soil using the material properties of soils. The liquid-plastic limit test is useful for obtaining basic information of soil, and is an effective method for classifying silt and clay, as well as the material properties, such as shear strength, shrinkage, and expansion. Unlike the liquid limit test, the plasticity limit test is due to the ambiguity of the test procedure. Many geotechnical engineers and scholars have questioned the test results. In this study, a new plasticity limit method was used to compare with the thread rolling method with kaolinite, ilite and bentonite at a certain ratio, and samples were collected from the west coast of Korea. As a result of the comparison, the test value of the new test method showed high reproducibility because the error range of the test value of the conventional thread rolling test was only 10% but the error range of the new test values decreased to 2%. The difference in the slope of the existing plasticity test values was 0.1519 ~ 0.1925, and the results of the test were similar or coincided with each other. Aone - point method was proposed to make it easier to apply the new test method.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.2
• /
• pp.5-17
• /
• 2023

In this study, a classification and uniaxial compression test of soil was conducted on 15 collapsed sites to use ground improvement with excellent protection effect owing to the increase of localized heavy rain in Korea. The Casagrande method and fall cone test were performed on the field soil to derive an expression for comparing liquid limit and plastic limit values, soil classification, and correlation between each other. By deriving the optimal mixing ratio of the ground improvement agent using uniaxial compressive strength for each soil classification, the classification of the fine-grained soil was not clear owing to the proficiency difference and test error. However, after classifying using the fall cone test, it was possible to suggest a clear optimal mixing ratio.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.2
• /
• pp.65-76
• /
• 2014

For soil improvement, sand mats or sand compaction piles are often constructed on soft marine clays. In such cases, some amounts of sand and clay are inevitably mixed. Sand or gravel often exists in the weathered soils near the slope surface. This research investigates the effect of mixing sand content on consistency limits and shear strength of clays. Firstly, sand was mixed with kaolinite or bentonite at 0, 9, 17, 23, 29, 33, 50% and then liquid and plastic limits were measured. Both plastic and liquid limits decreased as a sand content increased. The water content of clay-sand mixtures with different sand content increased by 10% or 20% step by step and then their undrained shear strength was measured using a portable vane shear device called Torvane. For all cases, undrained shear strength of clay-sand mixtures decreased rapidly until reaching a certain value. Their state changed from undrained to drained state gradually as the sand content increased, which caused their undrained shear strength to decrease. On the other hand, a series of direct shear tests were also conducted on such clay-sand mixtures to investigate the effect of sand content on cohesion and angle of internal friction. It was found from clay-sand mixtures that their cohesion decreased but angle of internal friction increased as the sand content increased.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.12
• /
• pp.7-20
• /
• 2017

In this study, effects of grain size distribution on the shear strength and rheological properties are investigated for coarse- and fine-grained soils by using direct shear apparatus. Shear strengths are estimated for fine-grained soils with the maximum particle size of 0.075 mm and coarse-grained soils with the maximum particle size of 0.425 mm and fine contents of 17% prepared at dry and liquid limit states. The direct shear tests are conducted under the relatively slow shear velocity, which corresponds to the reactivated landslide or debris flow after collapse according to the landslide classification. In addition, for the evaluation of rheological properties, residual shear strengths for both fine- and coarsegrained soils prepared under liquid limit states are obtained by multiple reversal shear tests under three shear velocities. From the relationship between residual shear strengths and shear rates, Bingham plastic viscosity and yield stress are estimated. The direct shear tests show that cohesions of fine-grained soil are greater than those of coarse-grained soil at both dry and liquid limit states. However, internal friction angles of fine-grained soil are smaller than those of coarse-grained soil. In case of rheological parameters, the plastic viscosity and yield stress of fine-grained soils are greater than those of coarse-grained soils. This study may be effectively used for the prediction of the reactivated landslide or debris flow after collapse.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.391-398
• /
• 2000

The index properties of cohesive soils play an important role to examine entire tendency of soil properties. Especially, the Atterberg limits have a good correlation with compression and shear strength of cohesive soils. However, these values strongly depend on their testing methods. In this study, for Pusan clays the Atterberg limits were peformed under different conditions; for example, four kinds of specimen preparation, two kinds of testing equipment, and four kinds of estimating method. And a laboratory vane test was peformed to compare the undrained shear strength with that of the fall cone test. As experimental results, the value of liquid limit performed for oven-dried sample, followed in ASTM D4318, underestimated by about 10% compared to those of another three methods, irrespective to the used equipments. But the value of plastic limit was not influenced by sample preparation methods and equipments. The liquid limits by one-point methods(Leroueil et al., 1996; Nagaraj et al., 1981) were agreed well with those of different methods. Finally, the undrained shear strength by laboratory vane test was relatively larger than that of fall cone test, and the relationship between both showed a bad trend.

• Journal of Industrial Technology
• /
• v.25 no.A
• /
• pp.57-65
• /
• 2005

In this paper, for the highly plastic marine soft clay distributed in west and southern coast of Korean peninsula of Kwangyang and Busan New Port areas, correlation between compression index and other indices representing geotechnical engineering properties such as liquid limit, void ratio and natural water content were analyzed. Appropriate empirical equations of being able to estimate the compressibility of clays in the specific areas were proposed and compared with other existing empirical ones. For analyses of the data and test results, data for marine clays were used from areas of the South Container Port of the Busan New Port, East Breakwater, Passenger Quay, Jungma Reclamation and Reclamation Containment in the 3rd stage in Kwangyang. In order to find the best regression model by using the commercially available software, MS EXCEL 2000, results obtained from the simple linear regression analysis, using the values of liquid limit, initial void ratio and natural water content as independent variables, were compared with the existing empirical equations. Multiple linear regression was also performed to find the best fit regression curves for compression index and other soil properties by combining those independent variables. On the other hands, another software of SPSS for non-linear regression was used to analyze the correlations between compression index and other soil properties.

• Resources Recycling
• /
• v.7 no.5
• /
• pp.41-45
• /
• 1998

A Hew way of contact angle measurement is derived based on simple geometrical calculation. Without using complicated contact angle measurement instrument. Just measuring the diameter and height of liquid lens made it possible to calculate the contact angle value with a reasonable reliability. To validate the contact angle value obtained by this method, contact angle of the same liquid lens is measured using conventional goniometer and it is verified that two values are nearly same within the limit of observational error.

• Computers and Concrete
• /
• v.31 no.6
• /
• pp.501-511
• /
• 2023

The strengthening efficiency of biopolymer treated soil depends on biopolymer type, concentration ratio, soil type, initial water content, curing time and mixing method. In this study, the physical and mechanical properties of xanthan gum (XG) treated kaolinite were investigated through compaction test, Atterberg limit test, triaxial test and unconfined compression test. The results indicated that the optimum water content (OWC) increased from 30.3% of untreated clay to 33.5% of 5% XG treated clay, while the maximum dry density has a slight increase from 13.96 kg/m³ to 14 kg/m³ of 0.2% XG treated clay and decrease to 2.7 kg/m³ of 5% XG treated clay. Meanwhile, the plastic limit of XG treated clay increased with the increase of XG concentration, while 0.5% XG treated clay can be observed the maximum liquid limit with 79.5%. Moreover, there are the ideal water content about 1.3-1.5 times of the optimum water content achieving the maximum dry density and curing time to obtain the maximum compressive strength for different XG contents, which the UCS is 1.52 and 2.07 times of the maximum UCS of untreated soil for 0.5% and 1% XG treated clay, respectively. In addition, hot-dry mixing can achieve highest UCS than other mixing methods (e.g., dry mixing, wet mixing and hot-wet mixing).