• Journal of Radiation Protection and Research
• /
• v.23 no.1
• /
• pp.7-15
• /
• 1998

In order to evaluate the effectiveness of some decontamination agents against skin contamination of $^{60}Co$ and $^{137}Cs$, the experiments were carried out in this study. In the experiments, pig skin was used instead of human skin , $^{60}CoC1_2$ and $^{137}CsCl$ were used the liquid sources of skin contamination. To examine the effectiveness of decontamination agents, skin decontamination was tried using soup, EDTA, KAERICON which was developed for decontamination of radionulides on the surface of building structure, and new decontamination agents such as IOCON, TRICON, and CHARCON, which were developed in this study. The absorption of radionuclides through the skin was evaluated by the gamma-tay detection on the surface of sample skin after radionuclides were penetrated into the skin during 16 hour soiling time. The results of this absorption experiment indicated that 11.5% and 3.2% of initial amounts of $^{137}Cs$ and $^{60}Co$, respectively, were panerated into the skin. In the experiment to remove the residual radioactivity fixed on the skin, KAERICON showed the decontamination rates up to 52.1%(decontamination factor of 2.1) and IOCON showed the equivalent decontamination rate (decontamination factor 1.9) for $^{137}Cs$. However, IOCON and CHARCON showed the poor decontamination rates of less than 20%(decontamination factor of 1.2) for $^{60}Co$, and KAERICON showed the poor decontamination rate (decontamination factor 1.1) for $^{60}Co$. For TRICON, the decontamination factors were 1.6 to 1.8 for $^{137}Cs$, and 1.0 to 1.2 for $^{60}Co$, respectively.

• Journal of Chitin and Chitosan
• /
• v.23 no.4
• /
• pp.244-255
• /
• 2018

Natural extract in liquid phase was adjusted to 0, 0.25, 0.5, 1, 2, and 4% concentration to check microbial changes and to measure 4, 8, $12^{\circ}C$ for refrigeration temperature. In the case of grapefruit extract, the microbial safety was maintained at all the concentrations at $4^{\circ}C$ storage, but the antimicrobial activity was maintained at $12^{\circ}C$ storage and at $8^{\circ}C$ and 21 days storage. In the case of grape seed extract, only the 4% of the culture at $8^{\circ}C$ satisfied the requirement of safety of food distribution for the last 21 days, and the safety criterion was satisfied only at 4% concentration at $12^{\circ}C$ for 18 days. Complex Scutellaria baicalensis extract showed the total number of microbial cells treated by concentration. It was confirmed that microbial flow safety was maintained at low temperature ($4^{\circ}C$). However, at $8^{\circ}C$ and $12^{\circ}C$, Exceeded the distribution limit. When polylysine was applied to brown rice cake, it showed activity in all groups except $4^{\circ}C$, but these properties were not observed at $8^{\circ}C$ and $12^{\circ}C$. At a concentration of 0.5% or more of chitosan, the growth of the microorganism is suppressed by the 21st day very stably, and a similar tendency is observed at 8 and $12^{\circ}C$, so that it may be an antimicrobial material that inhibits microorganisms. At the first day, the distribution standards for general bacterial counts were exceeded.Ethyl-pyruvate showed that microorganism safety was maintained at $4^{\circ}C$ and 1% concentration, and food safety was stable even at 2 or 4%. Glycine showed very good and stable distribution stability at $4^{\circ}C$. However, at $8^{\circ}C$ and $12^{\circ}C$, the shelf life of 14 days could not be maintained as with the addition of other antimicrobial active substances.

• The Korean Journal of Blood Transfusion
• /
• v.23 no.2
• /
• pp.115-126
• /
• 2012

Background: Umbilical cord (UC) is a promising source of mesenchymal stromal cells (MSCs). We compared the characteristics of MSCs from cryopreserved UC with those from fresh tissues, and demonstrated the possibility of UC cryopreservation for acquisition of MSCs from cryopreserved UC. Methods: Each UC was sliced into two types ($1{\sim}2mm^3$ vs. 0.5 cm), and cryopreserved in liquid nitrogen using different media (autologous cord blood plasma, aCBP vs. RPMI 1640). A fresh aliquot of $1{\sim}2mm^3$-sized UC was used as control tissue. After one week, the cryopreserved tissues were thawed and cultured. For the 0.5 cm UC, a slicing step into $1{\sim}2mm^3$ was needed. Cell count, viability, proliferative activity, and surface antigens were determined from harvested MSCs. Several growth factors (EGF, IGF-1, PDGF, TGF-${\beta}$, bFGF, and VEGF), were measured from the culture supernatant. Results: Eleven UC were enrolled in the study. Efficiencies of obtaining MSCs were higher in cryopreserved UC using RPMI 1640, compared with use of aCBP; the same result was observed for 0.5 cm sized UC, compared with $1{\sim}2mm^3$ sized UC. No difference in proliferative activity was observed between MSCs from fresh and cryopreserved UC. The amount of growth factors in culture supernatant using RPMI 1640 was larger than that of fresh tissues. Conclusion: We obtained growth factors from the supernatant as well as MSCs from cryopreserved UC. As with a cord blood bank, in the future, cryopreservation of UC for acquisition of both MSCs and growth factors would be possible in a time of need.

• Food Engineering Progress
• /
• v.13 no.3
• /
• pp.195-202
• /
• 2009

This study was accomplished that analysis of seven polycyclic aromatic hydrocarbons (PAHs) in smoked or nonsmoked processing foods by high performance liquid chromatography (HPLC) with fluorescence detection. The calibration line was constructed with injected different levels of standard concentration. Limit of detection (LOD) and limit of quantification(LOQ) showed higher linearity ($r^{2}$=0.998) reasonably, and recovery exhibited 0.033-0.666 $\mu$g/kg, 0.108-2.217 $\mu$g/kg and 69.31-90.14%, respectively. As a result, the samples using smoked tuna as smoked materials contained seven PAHs with different range from 0.256 to 0.486 $\mu$g/kg. The benzo[a]pyrene, indicator of PAHs, was detected to below the LOQ in two samples. Concentrations of benzo[a]pyrene in three samples were below the 2 $\mu$g/kg which is the limit of regulation. Smoked tuna sauces were detected from 0.321 to 0.552 $\mu$g/kg and not detected in drying powders. PAHs of smoked meat products were ranged from 0.720 to 2.027 $\mu$g/kg and are higher than concentration of tuna smoked samples. PAHs were very low in non-smoked foods including mustard, herb, and roasted meats.

• Journal of Food Hygiene and Safety
• /
• v.34 no.5
• /
• pp.413-420
• /
• 2019

In this study, a sample preparation method and a simultaneous determination method by ultra-high performance liquid chromatography coupled with tandem mass spectrometry for 9 isomers of chlorogenic acid and arbutin in fruits were developed. The samples were extracted using 90% methanol (pH 3.0), with the solutions being shaken and then sonicated for 10 min each. After centrifugation at 4,000 rpm for 10 min, the extraction was concentrated under a vacuum at $40^{\circ}C$ using a vacuum evaporator. The residue was dissolved in 5 mL of 5% methanol and filtered through a $0.45{\mu}m$ membrane before UHPLC-MS/MS analysis. The separations were performed on a C18 column with gradient elution of water (containing 0.1% formic acid) and methanol (containing 0.1% formic acid). The specificity, linearity, limit of detection, limit of quantification, accuracy, and precision of the proposed methods were also evaluated.

• Korean Journal of Plant Resources
• /
• v.32 no.5
• /
• pp.423-432
• /
• 2019

In order to select potential plant resources as functional materials and natural antioxidants, we evaluated antioxidant activity and serotonin derivatives of safflower germplasm collected from five countries. N-(p-Coumaroyl) serotonin (CS) and N-feruloylserotonin (FS) were analyzed by using Ultra Performance Liquid Chromatography (UPLC). Total polyphenol content (TPC) was determined by Folin-Ciocalteu method and antioxidant activities were estimated by 2,2-diphenyl-1-picryl-hydrazil (DPPH), 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) diammonium salt (ABTS), Ferric reducing antioxidant power (FRAP) and Reducing power (RP) assays. The TPC showed a range of 28.25 to $90.53{\mu}g$ gallic acid equivalent (GAE)/mg dried extract (DE). DPPH, ABTS, FRAP and RP assay were in the range of 18.76 to 93.98, 48.91 to 163.73, 3.80 to 132.29 and 26.32 to $80.08{\mu}g$ ascorbic acid equivalent (ASCE)/mg DE, respectively. Among the five countries, safflower seed collected from Iran had the highest levels of serotonin derivatives and antioxidant activities than other countries (p<0.05). CS showed high correlation with TPC, ABTS and DPPH (r=0.673,0.727,0.820), and FS showed high correlation with DPPH (r=0.740). Accessions IT321214 and IT321215 could be useful for development of new functional materials and could be used as a source of valuable natural antioxidant materials.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.1-2
• /
• 2011

Hybrid rockets have lately attracted attention as a strong candidate of small, low cost, safe and reliable launch vehicles. A significant topic is that the first commercially sponsored space ship, SpaceShipOne vehicle chose a hybrid rocket. The main factors for the choice were safety of operation, system cost, quick turnaround, and thrust termination. In Japan, five universities including Hokkaido University and three private companies organized "Hybrid Rocket Research Group" from 1998 to 2002. Their main purpose was to downsize the cost and scale of rocket experiments. In 2002, UNISEC (University Space Engineering Consortium) and HASTIC (Hokkaido Aerospace Science and Technology Incubation Center) took over the educational and R&D rocket activities respectively and the research group dissolved. In 2008, JAXA/ISAS and eleven universities formed "Hybrid Rocket Research Working Group" as a subcommittee of the Steering Committee for Space Engineering in ISAS. Their goal is to demonstrate technical feasibility of lowcost and high frequency launches of nano/micro satellites into sun-synchronous orbits. Hybrid rockets use a combination of solid and liquid propellants. Usually the fuel is in a solid phase. A serious problem of hybrid rockets is the low regression rate of the solid fuel. In single port hybrids the low regression rate below 1 mm/s causes large L/D exceeding a hundred and small fuel loading ratio falling below 0.3. Multi-port hybrids are a typical solution to solve this problem. However, this solution is not the mainstream in Japan. Another approach is to use high regression rate fuels. For example, a fuel regression rate of 4 mm/s decreases L/D to around 10 and increases the loading ratio to around 0.75. Liquefying fuels such as paraffins are strong candidates for high regression fuels and subject of active research in Japan too. Nakagawa et al. in Tokai University employed EVA (Ethylene Vinyl Acetate) to modify viscosity of paraffin based fuels and investigated the effect of viscosity on regression rates. Wada et al. in Akita University employed LTP (Low melting ThermoPlastic) as another candidate of liquefying fuels and demonstrated high regression rates comparable to paraffin fuels. Hori et al. in JAXA/ISAS employed glycidylazide-poly(ethylene glycol) (GAP-PEG) copolymers as high regression rate fuels and modified the combustion characteristics by changing the PEG mixing ratio. Regression rate improvement by changing internal ballistics is another stream of research. The author proposed a new fuel configuration named "CAMUI" in 1998. CAMUI comes from an abbreviation of "cascaded multistage impinging-jet" meaning the distinctive flow field. A CAMUI type fuel grain consists of several cylindrical fuel blocks with two ports in axial direction. The port alignment shifts 90 degrees with each other to make jets out of ports impinge on the upstream end face of the downstream fuel block, resulting in intense heat transfer to the fuel. Yuasa et al. in Tokyo Metropolitan University employed swirling injection method and improved regression rates more than three times higher. However, regression rate distribution along the axis is not uniform due to the decay of the swirl strength. Aso et al. in Kyushu University employed multi-swirl injection to solve this problem. Combinations of swirling injection and paraffin based fuel have been tried and some results show very high regression rates exceeding ten times of conventional one. High fuel regression rates by new fuel, new internal ballistics, or combination of them require faster fuel-oxidizer mixing to maintain combustion efficiency. Nakagawa et al. succeeded to improve combustion efficiency of a paraffin-based fuel from 77% to 96% by a baffle plate. Another effective approach some researchers are trying is to use an aft-chamber to increase residence time. Better understanding of the new flow fields is necessary to reveal basic mechanisms of regression enhancement. Yuasa et al. visualized the combustion field in a swirling injection type motor. Nakagawa et al. observed boundary layer combustion of wax-based fuels. To understand detailed flow structures in swirling flow type hybrids, Sawada et al. (Tohoku Univ.), Teramoto et al. (Univ. of Tokyo), Shimada et al. (ISAS), and Tsuboi et al. (Kyushu Inst. Tech.) are trying to simulate the flow field numerically. Main challenges are turbulent reaction, stiffness due to low Mach number flow, fuel regression model, and other non-steady phenomena. Oshima et al. in Hokkaido University simulated CAMUI type flow fields and discussed correspondence relation between regression distribution of a burning surface and the vortex structure over the surface.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.6
• /
• pp.427-446
• /
• 2008

A review on the papers published in the Korean Journal of Air-Conditioning and Refrigeration Engineering in 2006 has been accomplished. Focus has been put on current status of research in the aspect of heating, cooling, ventilation, sanitation and building environments. The conclusions are as follows. (1) The research trends of fluid engineering have been surveyed as groups of general fluid flow, fluid machinery and piping, etc. New research topics include micro heat exchanger and siphon cooling device using nano-fluid. Traditional CFD and flow visualization methods were still popular and widely used in research and development. Studies about diffusers and compressors were performed in fluid machinery. Characteristics of flow and heat transfer and piping optimization were studied in piping systems. (2) The papers on heat transfer have been categorized into heat transfer characteristics, heat exchangers, heat pipes, and two-phase heat transfer. The topics on heat transfer characteristics in general include thermal transport in a cryo-chamber, a LCD panel, a dryer, and heat generating electronics. Heat exchangers investigated include pin-tube type, plate type, ventilation air-to-air type, and heat transfer enhancing tubes. The research on a reversible loop heat pipe, the influence of NCG charging mass on heat transport capacity, and the chilling start-up characteristics in a heat pipe were reported. In two-phase heat transfer area, the studies on frost growth, ice slurry formation and liquid spray cooling were presented. The studies on the boiling of R-290 and the application of carbon nanotubes to enhance boiling were noticeable in this research area. (3) Many studies on refrigeration and air conditioning systems were presented on the practical issues of the performance and reliability enhancement. The air conditioning system with multi indoor units caught attention in several research works. The issues on the refrigerant charge and the control algorithm were treated. The systems with alternative refrigerants were also studied. Carbon dioxide, hydrocarbons and their mixtures were considered and the heat transfer correlations were proposed. (4) Due to high oil prices, energy consumption have been attentioned in mechanical building systems. Research works have been reviewed in this field by grouping into the research on heat and cold sources, air conditioning and cleaning research, ventilation and fire research including tunnel ventilation, and piping system research. The papers involve the promotion of efficient or effective use of energy, which helps to save energy and results in reduced environmental pollution and operating cost. (5) Studies on indoor air quality took a great portion in the field of building environments. Various other subjects such as indoor thermal comfort were also investigated through computer simulation, case study, and field experiment. Studies on energy include not only optimization study and economic analysis of building equipments but also usability of renewable energy in geothermal and solar systems.

• Food Science and Preservation
• /
• v.15 no.5
• /
• pp.725-730
• /
• 2008

The effects of acetic acid fermented juice prepared with submerged culture media of Antrodia camphorata mycelium (AJA: pH 3.2, acidity 2.0, Brix degree 3.2) on blood glucose levels and serum lipid profiles of rats in which diabetes was induced with streptozotocin (STZ) were investigated. Rats were divided into normal controls (NC), diabetic controls (DM), and groups receiving diluted (1:1, with water) AJA (A1) and undiluted AJA (A2). The volume of liquid given to both A1 and A2 animals was 0.5 mL/100 g body weight. In the A1 and A2 groups, compared with the DM group, polyphagia, liver enlargement, and weight loss caused by diabetes were considerably alleviated, but did not attain the levels of NC group rats. In the A1 and A2 groups, the levels of blood glucose were 17.1% and 28.2% lower than in the DM group. There was no significant difference in the levels of fructosamine between the DM and A1 group, but the A2 group had a level 16.3% lower than the DM group. In the A1 and A2 groups, compared with the DM group, serum triglyceride levels decreased by 44.1-48.0%, serum total cholesterol by 24.0-31.1%, and serum LDL-cholesterol by 25.2-51.1%. The level of HDL-cholesterol in A2 animals rose by 45.9% compared to NC rats. The results show that AJA may be a useful beverage for diabetes patients, offering both antihyperglycemic activity and improvement in levels of serum lipids.

• Geophysics and Geophysical Exploration
• /
• v.8 no.1
• /
• pp.67-72
• /
• 2005

To investigate the feasibility of a new concept of storing Liquefied Natural Gas (LNG) in a lined hard rock cavern, and to develop essential technologies for constructing underground LNG storage facilities, a small pilot plant storing liquid nitrogen (LN2) has been constructed at the Korea Institute of Geoscience and Mineral Resources (KIGAM). The LN2 stored in the cavern will subject the host rock around the cavern to very low temperatures, which is expected to cause the development of an ice ring and the change of ground condition around the storage cavern. To investigate and monitor changes in ground conditions at this pilot plant site, geophysical, hydrogeological, and rock mechanical investigations were carried out. In particular, geophysical methods including borehole radar and three-dimensional (3D) resistivity surveys were used to identify and monitor the development of an ice ring, and other possible changes in ground conditions resulting from the very low temperature of LN2 in the storage tank. We acquired 3D resistivity data before and after storing the LN2, and the results were compared. From the 3D images obtained during the three phases of the resistivity monitoring survey, we delineated zones of distinct resistivity changes that are closely related to the storage of LN2. In these results, we observed a decrease in resistivity at the eastern part of the storage cavern. Comparing the hydrogeological data and Joint patterns around the storage cavern, we interpret this change in resistivity to result from changes in the groundwater flow pattern. Freezing of the host rock by the very low temperature of LN2 causes a drastic change in the hydrogeological conditions and groundwater flow patterns in this pilot plant.