• Economic and Environmental Geology
• /
• v.23 no.1
• /
• pp.73-79
• /
• 1990

Controlled source audio-frequency magnetotelluric (CSAMT) has the great advantage of efficient mapping resistivity distribution and relatively deep depth of investigation. Moreover, CSAMT may be regarded more attractive than audio-frequency magnetotelluric in the sense of the strong and controllable signal. However, it has the problem such as undershoot and/or near-field effect that is hard to be interpreted if the interpretation method of MT is directly applied. The problem arises from the existance of controlled source which makes CSAMT attractive. So the characteristics of CSAMT response should be thoroughly understood prior to interpretation stage. In this study, numerical modeling program for horizontally layered earth was developped for the interpretation of CSAMT field data. CSAMT field survey was run as a follow-up to resistivity dipole-dipole study over the same survey line at Bongmyung coal mine. The survey used a grounded dipole source 2 Km in length and located 7.5Km south in this study. A good agreement between field CSAMT data and calculated data was demonstrated even in geologically complex earth situations.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.4
• /
• pp.8-15
• /
• 2003

When a typoon sets into harbour, a moored ship shows erratic motions and even mooring line failure may occur. such troubles may be caused by harbour resonance phenomena, resulting in large motion amplitudes at low frequency, which is close ti the natural frequency of th moored ship. The nonlinear motions of a ship moored to quay are simulated under external forces due to wave, current including mooring forces in time domain. The forces due to waves are obtained from source and dipole distribution method in the frequency domain. The current forces are calculated by using slow motion maneuvering equation in the horizontal plane. The wind forces are calculated from the empirical formula of ABS and the mooring forces of ropes and fenders are modeled as linear spring.

• Journal of Mechanical Science and Technology
• /
• v.19 no.5
• /
• pp.1116-1122
• /
• 2005

A finite element method was used to simulate the wave propagation of laser-generated ultrasound and its interaction with surface breaking cracks in an elastic material. Thermoelastic laser line source on the material surface was approximated as a shear dipole and loaded as nodal forces in the plane-strain finite element (FE) model. The shear dipole- FE model was tested for the generation of ultrasound on the surface with no defect. The model was found to generate the Rayleigh surface wave. The model was then extended to examine the interaction of laser generated ultrasound with surface-breaking cracks of various depths. The crack-scattered waves were monitored to size the crack depth. The proposed model clearly reproduced the experimentally observed features that can be used to characterize the presence of surface-breaking cracks.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.3
• /
• pp.259-267
• /
• 2004

A finite element method is used to simulate interaction of laser-based ultrasounds with surface breaking tracks in elastic media. The laser line source focused on the surface of semi-infinite medium is modeled as a shear dipole in 2-D plane strain finite elements. The shear dipole-finite clement model is found to give correct directivity patterns for generated longitudinal and shear waves. The interaction of surface waves with surface breaking cracks (2-D machined slot) is considered in two ways. Both the source and receiver are fixed with respect to the cracks in the first case, while the source is moving in another case. It is shown that the crack depth tested in the range of 0.3-5.0mm $({\lambda}_R/d=0.21{\sim}3.45)$ can be measured using the corner reflected waves produced by the fixed laser source. The moving laser source is found to cause a large amplitude change of reflected waves near crack, and the crack whose depth is one order lower than the wavelength ran be detected from this change.

• Journal of the Korean earth science society
• /
• v.24 no.4
• /
• pp.361-368
• /
• 2003

We have investigated the electric resistivity structure of the fault zone located in the Hongseong area where a big earthquake with M 5.0 occurred in 1978. Usually, Electric and Electromagnetic methods are broadly operated in the field of engineering works since these methods are effective to understand the distribution of geological weak zones - fault or fracture zones. We have conducted the dipole-dipole array resistivity method and MT(magnetotelluric) method and interpreted the resistivity distribution of the fault zone with the aid of various inversion methods. An MT survey was performed at 18 points along a 2.9 km survey line perpendicular to the fault line and a magnetic dipole source was used to enhance the S/N ratio in the high frequency. A Electric dipole-dipole array resistivity survey with the dipole length of 50 meters was carried out perpendicular to the fault. In view of two survey results, the fault marks the boundary between two opposite resistivity structures, especially the low resistivity zone is exhibited deeply through the prospective fault line. The result that the low resistivity zone is located at the center of the fault zone corresponds with the fact that the fault zone of the Hongseong area is active. We expect these results to provide basic information about the physical properties of fault zones in Korea.

• Journal of Magnetics
• /
• v.21 no.1
• /
• pp.153-158
• /
• 2016

This paper aims to discuss the Non Darcy boundary layer flow of non-conducting viscous fluid with magnetic ferroparticles over a permeable linearly stretching surface with ohmic dissipation and mixed convective heat transfer. A magnetic dipole is applied "a" distance below the surface of stretching sheet. The governing equations are modeled. Similarity transformation is used to convert the system of partial differential equations to a system of non-linear but ordinary differential equations. The ODEs are solved numerically. The effects of sundry parameters on the flow properties like velocity, pressure, skin-friction coefficient and Nusselt number are presented. It is deduced the frictional resistance of Lorentz force decreases with stronger electric field and the trend reverses for temperature. Skin friction coefficient increase with increase in ferromagnetic interaction parameter. Whereas, Nusselt number decrease.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.172-178
• /
• 2003

As a typoon gets into harbour, a moored ships shows erratic motions and even mooring line failures is occurred. Such troubles may be caused by harbour resonance phenomena, result in large motion amplitudes at law frequency, which is closed to the natural frequency of the moored ship. The nonlinear motions of a moored ship beside quay are simulated under external forces due to wave, current including mooring forces in time domain. The forces due to waves are obtained from source and dipole distribution method in the frequency domain. The current forces are calculated by using slow motion maneuvering equation in the horizontal plane. The wind forces are calculated from emperical formula of ABS and the mooring forces of ropes and fenders are modeled as linear spring.

• Journal of KSNVE
• /
• v.8 no.4
• /
• pp.603-608
• /
• 1998

In order to obtain basic data for the prediction of railway noise propagation, the noise radiation characteristics (source position, radiation directivity, etc) of trains were measured by using the sound intensity method. The measurements were performed at a side of railway by setting an intensity-probe array. As the measurement results, it was found that rolling noise due to interaction between wheel and rail and motor noise radiation from the lower part of train are dominant. The location of main sound sources can be described as being at the height of 0.1m in the center line of track, and the radiation directivity in the cross section of actually running trains are presented as a dipole source.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.504-511
• /
• 2001

In this research, we developed a computer program that designs a centrifugal impeller and diffuser, and predicts the far-field noise from the impeller. To design the impeller optimally, the TEIS model, which was originally developed by Japkise(1985), and the mean-line analysis are combined to predict the performance and design the optimal impeller simultaneously. The geometric configurations are provided by a GUI software (iDesignComp). The noise from impeller can be computed by the rapid loading procedure, which generates a surface between two blades and calculates the pressure distributions on the suction and pressure sides. The steady loading noise is computed by the rotating dipole source distribution via Ffowcs Williams & Hawkings equation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1355-1359
• /
• 2000

In this study, the insertion losses of various track-side railway noise barriers are analyzed by using a two-dimensional numerical boundary element method(BEM). The BEM is implemented using two out-of-phase monopole sources for each track to represent dipole source. All model for this study is based on actual size built in Test Line of KTX. And the results suggest that vertical absorptive barrier provide as effective screening as rigid barrier which is more 0.4 m than the height of those.