• Journal of Welding and Joining
• /
• v.32 no.4
• /
• pp.55-62
• /
• 2014

The use of light-weight Al alloys in the automotive industry is increasing to meet requirements for fuel efficiency and emission reduction. Joining Al alloy to the conventional steel sheet is also very important issue with the increased use of Al alloy, and several joining processes have been introduced to enhance joining strength between dissimilar metals. This paper deals with a galvanic corrosion in the dissimilar metal joining. Salt spray tests up to 2000 hours were conducted on a self-piercing rivet, spot welded, adhesive bonded and weld-bonded joints, and cross-sections and tensile shear strength according the salt spray duration were analyzed at every 500-hour. Self-piercing rivet joint had relative low initial strength but the joint strength did not change regardless of the salt spray duration. The strength of other joints (spot welded, adhesive bonded and weld-bonded joints) decreased with the increase of salt spray duration and the corrosion behaviour of each joint was discussed.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.3
• /
• pp.19-26
• /
• 2020

Steel production requires high-quality surfaces with minimal defects. Therefore, the detection algorithms for the surface defects of steel strip should have good generalization performance. To meet the growing demand for high-quality products, the use of intelligent visual inspection systems is becoming essential in production lines. In this paper, we proposed a ShuffleDefectNet defect detection system based on deep learning. The proposed defect detection system exceeds state-of-the-art performance for defect detection on the Northeastern University (NEU) dataset obtaining a mean average accuracy of 99.75%. We train the best performing detection with different amounts of training data and observe the performance of detection. We notice that accuracy and speed improve significantly when use the overall architecture of ShuffleDefectNet.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.2
• /
• pp.115-119
• /
• 2016

Winding is one of the major processes in roll-to-roll systems. Taper tension profile in a winding determines the distribution of stress in the radial direction, i.e., the radial stress in the wound rolls. Maximum radial stress is major cause of material defect, and this study has been actively proceeded. Traditional models of radial stress model were focused on flexible and light substrate. In this study, we developed an advanced radial stress model including effects of both these parameters(weight and stiffness) on the radial stress. The accuracy of the developed model was verified through FEM(Finite Element Method) analysis. FEM result of maximum radial stress value corresponds to 99 % in comparison to result with the model. From this study, the material defects does not occur when the steel winding. And steel industry can be applied to improve the winding process.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.694-699
• /
• 2002

In autobody assembly, thin-wall, tubular connections have been used for the frame structure. Recent interest in light materials, such as aluminum or magnesium alloys, has been rapidly growing for weight reduction and fuel efficiency. Due to higher thermal expansion coefficient, low stiffness/strength, and low softening temperature of aluminum and magnesium alloys, control of welding-induced distortion in these connections becomes a critical issue. In this study, the material sensitivity to welding distortion was investigated using a T-tubular connection of three types materials; low carbon steel (A500 Gr. A), aluminum alloy (5456-H116) and magnesium alloy (AZ91C-T6). An uncoupled thermal and mechanical finite element analysis scheme using the ABAQUS software program was developed to model and simulate the welding process, welding procedure and material behaviors. The predicted angular distortions were correlated to the cumulative plastic strains. A unique relationship between distortion and plastic strains exists for all three materials studied. The amount of distortion is proportional to the magnitude and distribution of the cumulative plastic strains in the weldment. The magnesium alloy has the highest distortion sensitivity, followed by the other two materials with the steel connection having the least distortion. Results from studies of thin-aluminum plates show that welding distortion can be minimized by reducing the cumulative plastic strains by preventing heat diffusion into the base metal using a strong heat sink placed directly beneath the weld. A rapid cooling method is recommended to reduce welding distortion of magnesium tubular connections.

• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.441-455
• /
• 1997

The need for rehabilitation of the existing bridges is a growing concern in many countries and has been emphasized in various research reports and publications. Many bridges constructed between 1960s and 1970s in Korea were designed for relatively light traffic volumes, speeds and the weight, thus they are inadequate for the present traffic conditions. This together with some design deficiencies, has resulted in deficiencies of various degrees of many bridges. One strengthening method which has significant advantages is the application of external post-tensioning tendons. This paper presents an example of three span continuous composite bridge strenghtened by application of external post-tensioning.

• Journal of Korean Society of Steel Construction
• /
• v.10 no.1 s.34
• /
• pp.11-24
• /
• 1998

The composite sandwich plate is constructed by combining two laminated facings with high strength and a thick core of light weight material. The governing equations for the analysis of bending of simply supported sandwich plates with laminated facings are derived and analysed using the analytical method including the local shear deformations. The accuracy of the approach is ascertained by comparing solutions from the sandwich plate theory with composite facings to the laminate plate theory. Since the present analysis considers the bending stiffness of the core and also the transverse shear deformations of the laminated facings, it is expected that the analysis is capable to analyze the general anisotropic laminated plates with global shear deformations.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.1
• /
• pp.105-112
• /
• 2011

Increasing needs for light weight and high safety in modern automobiles induced the wide application of high strength steels in automotive body structures- The main difficulty in the forming of sheet metal parts with high strength steel is the large amount of springback including sidewall curl and twist in channel shaped member parts- Among these shape defects, twist occurs frequently and requires numerous reworks on the dies to compensate the shape deviation- But until now, it seems to be no effective method to reduce the twist in the forming processes- In this study, a new forming process to reduce the twist deformation during the forming of automotive structural member was suggested- This method consists of forming and restriking of embosses on the sidewall around the stretch flanging area of the part- and was applied in the forming process design of an automotive front side inner member with high strength steel- To evaluate the effectiveness of the method, springback analysis using $Pamstampa^{tm}$ was done- Through the analysis results, the suggested method was proven to be effective in twist reduction of channel shaped parts with stretch flanging area.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.543-550
• /
• 2007

As an emerging materials in construction fields, FRP(fiber reinforced polymer) has been used in many area of civil engineering for its light weight and high strength. In this study we chose the 2nd Jindo-Bridge as a prototype, and evaluate effect of replacing steel components to FRP components through simplified 3D linear analysis. Static and modal analysis are done and the analysis results are compared with steel case analysis. From the static analysis results, the maximum stress of each component and maximum displacement of middle span are compared. Due to the reduction of deadload, the FRP structure causes less deflection than the original steel structure and from the reduced section (cable) analysis we confirmed the previous result. The occurrence wind velocity of flutter is compared by the frequency ratio.

• Laser Solutions
• /
• v.16 no.3
• /
• pp.1-10
• /
• 2013

In this study, Al-Si coated boron steel(1.2 mm) were laser welded by $CO_2$ laser and hot-stamping was applied to the laser joints. Tensile properties and microstructures of the joints were investigated before and after hot-stamping. Tensile and yield strengths of the as welded specimen similar with base metal and fracture occurred base metal of boron steel. Although, in case of heat treated specimen, fracture occurred fusion zone that Al segregated zone near the bond line. These could be explained by the existence of ferrite, in the Al segregated zone near the bond line and base metal of boron steel. Before hot-stamping, hardness of base metal is lower than fusion zone and heat affected zone in spite of exist Al segregation zone($Fe_3$(Al,Si)). So fracture occurred base metal. Although, after hot-stamping, microstructure of base metal and welds zone transformed to martensite and bainite except in Al segregation zone near the bond line that $Fe_3$(Al,Si) transformed to a-ferrite. So fracture occurred Al segregation zone near the bond line.

• Tunnel and Underground Space
• /
• v.22 no.3
• /
• pp.221-225
• /
• 2012

Magnesium is one of the light weight materials, which can improve fuel economy and reduce emissions in automotive industry. Recently, magnesium alloys have gained considerable attention due to good mechanical properties. In this work, we have performed an explosive welding using the magnesium alloys (AZ31) and stainless steel (SUS 304). As a result, SUS304/AZ31 were successfully combined each other; however, a resolidified interlayer was observed at the point of welded layer. To reduce the resolidified interlayer, we have changed the thickness (0.5 mm and 1 mm) of stainless steel, distance (45 mm and 60 mm) between explosive and the center of materials and initial angle ($20^{\circ}$ and $30^{\circ}$) of explosive. In the case of the thickness 0.5 mm and angle of $30^{\circ}$, the resolidfied interlayer was not observed due to the increase of distance from the explosive. To accurately estimate the resolidified interlayer, electron probe micro-analyzer (EPMA) method and hardness were used. For the EPMA analysis, mixed materials were confirmed at the resolidified interlayer, and the measurement exhibited the middle value compared with the AZ31 and SUS304.