• Journal of the Korean Society of Combustion
• /
• v.19 no.3
• /
• pp.18-25
• /
• 2014

Bottom ash from a coal-fired power plant is usually landfilled to a nearby site, which causes a growing environmental concern and increased operating costs. One way of recycling the bottom ash is to produce light-weight aggregate (LWA) using a rotary kiln. This study investigated the temperature profiles of raw LWA particles in a rotary kiln to identify the range of operating conditions appropriate for ideal bloating. For this purpose, a new simulation method was developed to integrate a 1-dimensional model for the bed of LWA particles and the computational fluid dynamics (CFD) for the fuel combustion and gas flow. The temperature of LWA particles was found very sensitive to the changes in the air preheating temperature and excess air ratio. Therefore, an accurate control of the operation parameters was essential to achieve the bloating of LWA particles without excessive sintering or melting.

• Journal of the Korea Concrete Institute
• /
• v.23 no.6
• /
• pp.723-730
• /
• 2011

It is very important to experimentally evaluate concrete behavior at elevated temperature because aggregates make up approximately 80 percent of volume in concrete. In this study, an experiment to evaluate mechanical properties of normal weight and light weight concrete of 60 MPa was conducted. Based on loading level of 0, 20 and 40 percent, the tests of 28 days compressive strength, elastic modulus, thermal strain, total strain, and transient creep using ${\phi}100{\times}200mm$ cylindrical specimens at elevated temperature were performed. Then, the results were compared with CEB (Committes Euro-international du Beton) model code. The results showed that thermal strain of light weight concrete was smaller than normal weight concrete. Also, the results showed that compressive strength of light concrete at $700^{\circ}C$ was higher than normal weight concrete and CEB code, similar to that obtained at ambient temperature. Transient creep developed from loading at a critical temperature of $500^{\circ}C$ caused the concrete strains to change from expansion to compression. The transient creep test result showed that internal force was high when the ratio of shrinkage between concrete and aggregate was more influential than thermal expansion.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.4
• /
• pp.66-76
• /
• 1999

In this study , the optimum structural components for the rural house design using the light gauge cold-formed steel frame is proposed. The proposed components were optimzed by the developed model composed with the analysis model and LGC database. The analysis model adapts FEA(finite element analysis). LGC database and calculation of element force adapt the design criteria of KISC. The structure of house is divided into header, bearing wall and foof truss. The variable of the each structure of house are defined component which designed by the case of load, aize and space. The designed weight were used for optimization procedure of the divided components.

• Journal of Auto-vehicle Safety Association
• /
• v.14 no.1
• /
• pp.32-38
• /
• 2022

In the automobile industry, lamps are frequently used as a mean to emphasize each company's brand identity. Therefore, many detailed design models have emerged in order to realize a differentiated image in preparation for competitive vehicles. Among them, the design of a multi compartment lighting image concept that realizes light divided in multiple space also being introduced by various manufacturers. In this study, in order to solve the problem of cost and weight rise that the existing multi compartment image lamp has, using TRIZ method such as functional analysis modeling and trimming. Through this process, an idea to minimize cost and weight was derived. As the idea was designed in detail, the formation of light did not go as desired, and the diffusion of light also proceeded differently than intended. In order to overcome this problem, a new concept of corrosion and diffusion structure was applied. Eventually, it overcomes various problems and successfully applied it to a real vehicle. The idea was actually reflected in the "Santa Fe" model. Later, the media focused on the lamps to which the idea was applied, and contributed to the sale of a large number of vehicles by providing consumers with a new light sensibility. During the research process, it was possible to secure a number of patents and knowledge of new design concepts.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.488-490
• /
• 2015

In this paper, the selfie stick which can involved in small bag is designed to make easier and smaller. Model the diameter of the selfie to achieve light weight for the fixed length using FreeCAD. After modeling, check durability using 'Netgen' and 'Calculix'.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.10
• /
• pp.5176-5183
• /
• 2013

In general, Korean Lightweight Concrete used Heat insulating material for building and filler for civil construction, backfill material for tunnel, office floor fillers, lightweight blocks and so on. These expand the range of use ALC(autoclaved lightweight concrete) on the soft-ground at regular intervals during road construction by installing piles used as substrates for the process is under study. In this study, behavior characteristics on the soft-ground of pavement analysis was used to test the geo-Centrifuge. Prototype pavement reduced to 1/30 slab form of the composition as kaolinite model tests were conducted in the soft ground. Pile Arrangement (having 36 component pile with an array of $3{\times}12$) was used to group of piles. Tests of gravity 30 level the centrifugal force acting Light-weight pavement models. Based on the Prototype pavement of the behavior characteristics of pavement behavior characteristics were estimated. FMA analysis of the 10 times as big 39.4kg (actual load 35 ton) of the lateral load is applied to the case 7.8mm (actual behavior 23.4mm) behavior was fine.

• Journal of the Korea Concrete Institute
• /
• v.22 no.2
• /
• pp.159-169
• /
• 2010

A multiphysics model analysis including moisture transport, heat transfer and solid mechanics and experiments on the normal and light weight concrete were carried out in order to study the effect of preabsorbed water in the light weight aggregates on the drying and shrinkage characteristics of concrete. Consequently, with fixed water-cement ratio, loss of water content of normal and light weight concrete were compared and the results showed that the lightweight concrete lost less moist than the normal concrete in early age and long term which was by moist supply effect. Accordingly, shrinkage strain size and distribution of lightweight concrete were decreased, and shrinkage reducing effect was efficient in early age with water cement ratio 0.3 and in both early age, and long term with water cement ratio 0.5. The comparison of analysis results and exaperimental results indicate that characteristic values of moisture transport and the relation humidity and shrinkage strain from this study are resonable for application for other differential shrinkage analysis in lightweight concrete.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.4 s.193
• /
• pp.93-101
• /
• 2007

Aluminum alloy which is one of the light materials has been tried to apply to light weight vehicle body. In order to do that, welding technology is very important. In case of the aluminum laser welding, the strength of welded part is reduced due to porosity, underfill, and magnesium loss. To overcome these problems, laser welding of aluminum with filler wire was suggested. In this study, experiment about laser welding of AA5182 aluminum alloy with AA5356 filler wire was performed according to process parameters such as laser power, welding speed and wire feed rate. The tensile strength was measured to find the weldability of laser welding with filler wire. The models to estimate tensile strength were suggested using three regression models and one neural network model. For regression models, one was the multiple linear regression model, another was the second order polynomial regression model, and the other was the multiple nonlinear regression model. Neural network model with 2 hidden layers which had 5 and 3 nodes respectively was investigated to find the most suitable model for the system. Estimation performance was evaluated for each model using the average error rate. Among the three regression models, the second order polynomial regression model had the best estimation performance. For all models, neural network model has the best estimation performance.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.164-169
• /
• 2005

The TTX(Tilting Train eXpress) is designed to achieve high driving speed up to 200 km/h and to run on conventional curved rails without speed reduction. In order to maintain power collection between catenary and pantograph collector while train body is tilted, the TTX pantograph must have tilting structure (or Sledge). The power quality is determined by the tilting structure. Static and dynamic characteristics of tilting structure, therefore, are important to evaluate the pantograph performance. The current prototype of the tilting structure is overweight model and its structural characteristics have not been investigated. In this study, the finite element model of TTX tilting structure is established and static analysis is performed. Finally, using this result, a light weight model is proposed.

• Korean Journal of Health Education and Promotion
• /
• v.34 no.1
• /
• pp.1-12
• /
• 2017

Objectives: The aim of this study was to verify relationships between light- and heavy alcohol drinking and health-risk behaviors such as smoking, inappropriate weight control, physical inactivity, and sexual activity among adolescents. Methods: The data of 68,043 adolescents in middle- and high school collected from the Korea Youth Risk Behavior Web-based Survey in 2015 were analyzed. For statistical analysis, logistic regression model was used. Results: The rate of heavy alcohol drinking increased with increasing age up to 21.5% among boys and 13.9% among girls. Among boys, heavy alcohol drinkers were at a higher risk of smoking (adjusted odds ratios [OR]=3.3, 95% confidence interval [CI]=2.8-3.8), inappropriate weight control (OR=1.7; 95% CI=1.4-2.1), having sexual intercourse (OR=3.6; 95% CI=3.0-4.2) than light drinkers. Multiple health-risk behaviors of smoking, inappropriate weight control and sexual intercourse also increased in accordance with the severity of drinking alcohol beverage compared to non-drinker. Physical inactivity was decreased among heavy drinkers compared to light drinkers (OR=0.8; 95% CI=0.7-0.9 for inactivity of moderate exercise). Similar results were observed among girls. Conclusions: Alcohol drinking especially heavy alcohol drinking among adolescents is related to other risky behaviors including smoking, inappropriate weight control, and sexual activity. To prevent health problems in adolescents, it is necessary to adopt a combined approach regarding heavy drinking and health-risk behaviors.