• 한국농촌건축학회논문집
• /
• 제22권1호
• /
• pp.13-20
• /
• 2020

As the number of plastic greenhouses has increased in Korea, the damage from typhoons and snow has also increased. Structural design codes for a disaster-resistant plastic greenhouse have been revised over the last few decades. In particular, the revised code draft in 2017 have changed in many ways compared to the 1995 code. Nevertheless, There is no study of the effect of new design code on plastic greenhouse. Therefore, this study evaluated the safety of plastic greenhouse against wind load according to 1995 and 2017 codes for type 1 houses, which is most commonly built in Jeju, through comparing the analytical results of plastic greenhouses designed by 1995 code and 2017 code draft. The results are as follows. (1) The uplift load due to the negative pressure on the roof of the plastic greenhouse increased significantly in 2017 code draft. (2) Since the existing members could not meet the design requirements, the rafters had to be replaced with members of the same cross-section as the columns. (3) Due to excessive lifting, measures were also needed to prevent lifting at the foundation of the plastic greenhouse.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.38-45
• /
• 2005

Chemical mechanical polishing(CMP) has been widely accepted for the planarization of multi-layer structures in semiconductor fabrication. But a variety of defects such as abrasive contamination, scratch, dishing, erosion and corrosion are occurred during CMP. Especially, dishing and erosion defects increase the metal resistance because they decrease the interconnect section area, and ultimately reduce the lift time of the semiconductor. Due to this reason dishing and erosion must be prohibited. The pattern density and size in chip have a significant influence on dishing and erosion occurred by over-polishing. The fixed abrasive pad(FAP) was applied and tested to reduce dishing and erosion in this paper. The abrasive concentration decrease of FAP results in advanced pattern selectivity which can lead the uniform removal in chip and declining over-polishing. Consequently, reduced dishing and erosion was observed in CMP of tungsten pattern wafer with proposed FAP and chemicals.

• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.194-201
• /
• 2006

Roof-fairing and deflector system have been used on heavy-duty trucks to minimize aerodynamic drag force not only for driving stability of the truck but also for energy saving by reducing the required driving power of the vehicle. In this study, a numerical simulation was carried out to see aerodynamic effect of the drag reducing device on the model vehicle. Drag and lift force generated on the five different models of the drag reducing system were calculated and compared them each other to see which type of device is efficient on the reduction of driving power of the vehicles quantitatively. An experiment has been done to see airflow characteristics on the model vehicles. Airflow patterns around the model vehicles were visualized by smoke generation method to compare the complexity of airflow around drag reducing device. From the results, the deflector systems(Model 5,6) were revealed as a better device for reduction of aerodynamic drag than the roof-fairing systems(Model 2,3,4) on the heavy-duty truck and it can be expected that over 10% of brake power of an engine can be saved on a tractor-trailer by the aerodynamic drag reducing device at normal speed range($80km/h{\sim}$).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1485-1487
• /
• 1997

Platinum-Cobalt alloy thin films were deposited on $Al_2O_3$ substrates by co sputtering for RTD temperature sensors. We made Pt-Co alloy resistance patterns on $Al_2O_3$ substrate by lift-off method and investigated the physical and electrical characteristics of these films under sputtering conditions (; the input power, working vacuum), annealing conditions (; temperature, time) and also after annealing these films. After the annealing treatment at $800^{\circ}C$ for 60min, the resistivity and sheet resistivity of Pt-Co thin films was $0.0302{\mu}{\Omega}{\cdot}cm$ and $0.1{\Omega}/{\square}$, respectively, and the TCR value of Pt-Co RTD was $3600ppm/^{\circ}C$ in the temperature range of $25{\sim}400^{\circ}C$. These results indicate that Pt-Co thin films have potential for the excellent RTD temperature sensors.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.431-434
• /
• 1998

Platinum-Cobalt alloy thin films were deposited on Al$_2$O$_3$ substrate by r.f. cosputtering for RTD temperature sensors. We made Pt-Co alloy resistance patterns on the Al$_2$O$_3$ substrate by lift-off method and investigated the physical and electrical characteristics of these films under various conditions (the input power, working vacuum, annealing temperature, thickness of thin films) and also after annealing these films. At input power of Pt : 4.4 W/$\textrm{cm}^2$, Co : 6.91 W/$\textrm{cm}^2$, working vacuum on and annealing conditions of 1000 $^{\circ}C$ and 60 min, the resistivity and the sheet resistive thin films were 15 ${\mu}$$\Omega$$.$cm and 0.5 $\Omega$/$\square$, respectively. The TCR value of Pt-Co a films was measured with various thickness of thin films and annealing temperature. T TCR value is gained under condition 3000${\AA}$ of thin films thickness and 1000$^{\circ}C$ of temperature. These results indicate that Pt-Co alloy thin films have potentiality for the wide temperature ranges.

• 한국지반공학회지:지반
• /
• 제8권3호
• /
• pp.5-12
• /
• 1992

본 논문은 모래지반에 박힌, 기하학적 특성과 설치방법이 서로 다른 모형말뚝의 극한상장지지력에 대한 연구이다. 기하학적 특성의 측면으로는 균일직편말뚝, 선단확대말뚝, 다층확대말뚝과 앵커플레이트가 시험되고 기일직경말뚝에 대한 말뚝설치방법이 극한지지력에 미치는 영향을 조사하기 위해 매설, ao입, 진동관입방법이 연구되었다. 실험결과에 의하면 기초가 상장력과 압축력을 받는 경우에는 선단확대 말뚝이, 오직 상장력에 대해서는 앵커플레이트가 가장 효과적이며, 또한 말뚝설치방법 및 타입 말뚝의 선단 모양은 상장지지목에 큰 영향을 준다는 것이 밝혀졌다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.335-338
• /
• 1997

Platinum-Cobalt alloy thin films were deposited on A1$_2$O$_3$substrate by magnetron cosputtering for RTD temperature sensors with wide temperature ranges. We made Pt-Co alloy resistance patterns on the A1$_2$O$_3$substrate by lift-off method and fabricated Pt-Co alley RTD temperature sensors by using Pt-wire, Pt-paste. We investigated the physical and electrical characteristics of theme films under various conditions, input power, working vacuum, annealing temperature and time, and also after annealing these films. The resistivity and sheet resistivity of these films were decreased with increasing the annealing temperature. At input power of Pt : 4.4 W/cm$^2$, Co : 6.91 W/cm$^2$, working vacuum of 10 mTorr and annealing conditions of 800$^{\circ}C$ and 60 min, the resistivity and sheet resistivity of Pt-Co thin films was 15${\mu}$$\Omega$$.$cm and 0.5$\Omega$/ , respectively, and the TCR value of Pt-Co alloy thin films with thickness of 3000${\AA}$ was 3740ppm/$^{\circ}C$ in the temperature range of 25∼600$^{\circ}C$. These results indicate that Pt-Co alloy thin films hove potentiality for the RTD with wide temperature ranges.

• Wind and Structures
• /
• 제28권3호
• /
• pp.155-170
• /
• 2019

This paper presents a novel test method for the galloping of iced conductor using wind generated by a moving vehicle which can produce relative wind field. The theoretical formula of transiting test is developed based on theoretical derivation and field test. The test devices of transiting test method for aerodynamic coefficient and galloping of an iced conductor are designed and assembled, respectively. The test method is then used to measure the aerodynamic coefficient and galloping of iced conductor which has been performed in the relevant literatures. Experimental results reveal that the theoretical formula of transiting test method for aerodynamic coefficient of iced conductor is accurate. Moreover, the driving wind speed measured by Pitot tube pressure sensors, as well as the lift and drag forces measured by dynamometer in the transiting test are stable and accurate. Vehicle vibration slightly influences the aerodynamic coefficients of the transiting test during driving in ideal conditions. Results of transiting test show that the tendencies of the aerodynamic coefficient curve are generally consistent with those of the wind tunnel tests in related studies. Meanwhile, the galloping is fairly consistent with that obtained through the wind tunnel test in the related literature. These studies validate the feasibility and effectiveness of the transiting test method. The present study on the transiting test method provides a novel testing method for research on the wind-resistance of iced conductor.

• Wind and Structures
• /
• 제28권2호
• /
• pp.71-87
• /
• 2019

The yaw and interference effects of blades affect aerodynamic performance of large wind turbine system significantly, thus influencing wind-induced response and stability performance of the tower-blade system. In this study, the 5MW wind turbine which was developed by Nanjing University of Aeronautics and Astronautics (NUAA) was chosen as the research object. Large eddy simulation on flow field and aerodynamics of its wind turbine system with different yaw angles($0^{\circ}$, $5^{\circ}$, $10^{\circ}$, $20^{\circ}$, $30^{\circ}$ and $45^{\circ}$) under the most unfavorable blade position was carried out. Results were compared with codes and measurement results at home and abroad, which verified validity of large eddy simulation. On this basis, effects of yaw angle on average wind pressure, fluctuating wind pressure, lift coefficient, resistance coefficient,streaming and wake characteristics on different interference zone of tower of wind turbine were analyzed. Next, the blade-cabin-tower-foundation integrated coupling model of the large wind turbine was constructed based on finite element method. Dynamic characteristics, wind-induced response and stability performance of the wind turbine structural system under different yaw angle were analyzed systematically. Research results demonstrate that with the increase of yaw angle, the maximum negative pressure and extreme negative pressure of the significant interference zone of the tower present a V-shaped variation trend, whereas the layer resistance coefficient increases gradually. By contrast, the maximum negative pressure, extreme negative pressure and layer resistance coefficient of the non-interference zone remain basically same. Effects of streaming and wake weaken gradually. When the yaw angle increases to $45^{\circ}$, aerodynamic force of the tower is close with that when there's no blade yaw and interference. As the height of significant interference zone increases, layer resistance coefficient decreases firstly and then increases under different yaw angles. Maximum means and mean square error (MSE) of radial displacement under different yaw angles all occur at circumferential $0^{\circ}$ and $180^{\circ}$ of the tower. The maximum bending moment at tower bottom is at circumferential $20^{\circ}$. When the yaw angle is $0^{\circ}$, the maximum downwind displacement responses of different blades are higher than 2.7 m. With the increase of yaw angle, MSEs of radial displacement at tower top, downwind displacement of blades, internal force at blade roots all decrease gradually, while the critical wind speed decreases firstly and then increases and finally decreases. The comprehensive analysis shows that the worst aerodynamic performance and wind-induced response of the wind turbine system are achieved when the yaw angle is $0^{\circ}$, whereas the worst stability performance and ultimate bearing capacity are achieved when the yaw angle is $45^{\circ}$.

• 콘크리트학회논문집
• /
• 제19권5호
• /
• pp.569-575
• /
• 2007

철근콘크리트 구조물의 수명 연장 및 기능 보완을 위하여 콘크리트 면의 보수를 실시할 경우 일반적으로 구조적 내력을 고려하지 않는다. 특히, 표면박락 등의 보수에는 단순하게 모르타르 도포만을 이용하여 보수가 완료되므로 별도의 구조적인 보강 성능을 발휘하지 않는다. 그러나 시공성의 향상 및 균열의 억제를 위하여 철망 등의 재료를 사용할 경우 일정부분 보강의 효과를 얻을 수 있을 것으로 예상되며, 특히, 수로 구조물과 같이 교각 간에 놓여지는 구조요소의 경우 하부면의 보수를 실시할 경우 휨 저항성의 증가를 기대할 수 있다. 따라서 본 연구에서는 크리프 철망에 의한 보수를 실시하고 보수 부위 및 보수 두께에 따른 보강 성능을 확인하고자 하였다. 이를 위하여 두께 150mm, 길이 3,000mm, 너비 600mm 슬래브를 제작하고, 상부 부분 보수, 상부 전면 보수, 하부 부분 보수, 하부 전면 보수, 크림프 철망 보강 유무 등 총 8개 실험 유형을 선택하고 이에 대한 휨 보강 성능 실험을 실시하였다. 분석 결과, 크림프 철망을 보강한 실험체에서 보수 재료의 두께가 증가할수록 항복하중 및 파괴하중은 높아지는 것으로 나타났으며, 동일 조건일 경우 하부면의 보수가 휨 하중에 대한 내력을 증가시킬 수 있는 것으로 나타났다. 또한, 휨 하중을 받는 구조물 중 부분 보수만을 실시할 경우 휨 보강 성능은 기대하기 어려운 것으로 나타났다. 결론적으로 크림프 철망에 의한 보수공법 적용 시 휨 저항성의 증가가 있는 것을 알 수 있었다.