• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.4
• /
• pp.705-713
• /
• 2016

For the soft ground construction, the factors not considered in the design stage occurs in the construction stage so that they cause the increase of the construction cost due to the structural stability and the design change. The subject of the study is the construction section of the industrial complex access road made in the Ochang region of Chungcheongbuk-do. The study is concerned with selecting the soft ground handling method such as the replacement method using rock debris and the surcharge reflecting the service load as the soft ground handling measure and analyzing the effect of reducing the construction cost with the stability of structures and the reduction of the construction period. The soft ground in the study section consists of sandy and cohesive soil and is 2.4m to 5.5m deep. It is distributed unevenly between the 1.5m to 5.9m stratums under the ground surface. Settlement is not serious, but the future uneven settlement and difference are expected so that the future settlement behavior is estimated by analyzing the site measurement results after the soft ground treatment. Moreover, in consideration of the regional characteristics and economic efficiency, soil with good quality is replaced with rock debris as the replacement material so that 29% of the construction cost is reduced due to the increase of stability and the reduction of duration. If the estimation of the dispersion of the pore water pressure within the dam body and the change of the underground water level and the relation of the actually measured soft ground with consolidation is studied further on the basis of the study, it is expected that the behavior of the soft ground will be correctly estimated in various site conditions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.8
• /
• pp.5534-5540
• /
• 2015

This In the railway signaling system, applications of axle counter in addition to track circuit goes on increasing for detecting train position. Consequently, this paper compares sensor methods of axle counter with between geo-magnetism method and proximity sensor method. And it presents differences and results, to improve reliabilities of train detection and axle counting. Also, this article presents an applied result which is based on field experience, with regard to installation, considering attachment condition of sensor part for accurate axle counting. This study acquires expandability that is able to perform not only axle counting function but also various other functions (direction detection of train, speed detection of train, and so on). It was a result of a change of design in order to judge phase difference of sensors, to improve reliability of axle counting. Furthermore, it does not subordinate to characteristics (type, weight of train). And it is confirmed that the omission of axle counting was not occurred in 350km/h. This was the result of Lab test after the construction of transfer equipment of trial axle and Test Bed for axle counting. Both of them are self-productions. Through this, it prepares foundation which is able to apply not only to train detection but also to speed of passing trains, formation number of trains, detector locking condition - when the train passes the section of switch point, and level crossing devices. Furthermore, it would be judged to contribute safety train operation if proximity sensor method applies to the whole railway signaling system from now on.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.517-529
• /
• 2020

Various facilities in the river working in a complex interdependence network result in both desired and adverse effects. Among these, the weir crossing the river continuously acts in various ways, such as securing river maintenance flow and water level during dry-period, and rising flood level during rainy period. Until now, weir planning was only limited to flood mitigation management. Recently, the demand for securing river environment functions is increasing. Therefore, the necessity for an environmental flow has emerged. Nevertheless, there is no analysis and evaluation of the ecological functional aspects applying the environmental flow when planning facilities. Therefore, this study aimed to develop and systematize an assessment method that considers not only flood control but also river environment. Environmental flow was applied to the weir named Dondaet-bo and hydraulic analysis was conducted for each retention, demolition, and re-installation case. Also, this research was conducted to minimize the impact on the surrounding river facilities and flood assessments from previous perspectives were performed. The study result demonstrated a plan to reinstall the weir as a natural riffle. Through this study, it is expected that the flood control and environmental functions of rivers can be secured in combination.

• Journal of Family Relations
• /
• v.21 no.1
• /
• pp.143-160
• /
• 2016

Objectives: The purpose of this study is to empirically verify the difference between traditional gender role attitude and realistic dual earner attitude. Most preceding studies analyzed gender role attitude by summated rating scale while few studies have been conducted on the difference between traditional gender role attitude and dual earner attitude. Method: By using the 9th Korea Welfare Panel Data (year 2014), this study extracted households of married couples and with children in working age (18 through 64 years of age) who are the main subjects in work-family relationship. First, this study classified traditional group and modern group in their gender role attitude and passive group and active group in their dual earner attitude and by crossing these attitudes, drew out 4 gender role/dual earner attitudes. For analysis, this study investigated frequency of attitude types through descriptive statistics. By conducting ANOVA, study verified if there are significant differences in the satisfaction with family relationship depending on the types of gender role/dual earner attitudes. Lastly, study examined the effect of socio-economic status and demographic characteristics on the types of gender role/dual earner attitudes by conducting multi-nominal logistic regression analysis. Results: As the result of analysis, first, half of respondents belonged to 'equal-role-oriented type' who has modern gender role attitude and active dual earner attitude. However, there were not a few 'dual-earner-avoiding type' who has modern gender role attitude but passive dual earner attitude and 'incongruous attitude type' who has traditional gender role attitude but active dual earner attitude. Next, 'incongruous attitude type' had significantly low level of satisfaction with overall family life, relationship with spouse and relationship with children than other attitude types. Lastly, those whose incomes belong to poor strata, those who are high school graduates and lower, males and those who are over the age of 60 had significantly higher probability of belonging to 'incongruous attitude type.' Conclusion: The results of analysis demonstrate that the difference between gender role attitude and dual earner attitude is an important matter and since 'incongruous attitude type' exhibits low level of satisfaction with family relationship, scrupulous policy approaches are required for those who have high possibility of belonging to 'incongruous attitude type.'

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.34 no.6
• /
• pp.303-314
• /
• 2022

The persistence analysis of marine physical environment factors is a basic analysis that must precede the use of sea areas as an analysis required in the coastal engineering such as downtime and design. In this study, the persistence analysis was implemented for wind speed and significant wave height data from four observation points of Deokjeokdo, Oeyeondo, Geomundo, and Geojedo among the marine meteorological observation buoys of the Korea Meteorological Administration. The persistence time means the consecutive time of observation data beyond specific level. The threshold wind speed and significant wave height were set in the range of 1~15 m/s and the range of 0.25~3.0 m, respectively. Then, the persistence time was extracted. As a result of the analysis, the persistence time of wind speed and significant wave height decreased rapidly as the reference value increased. The median persistence times under the maximum reference thresholds were assessed as a maximum of 5 hours for wind speed and a maximum of 8 hours for significant wave height. When the reference wind speed and significant wave height were 15 m/s and 3 m, respectively, the persistence time that could occur with a 1% probability were 52 and 56 hours. This study can be expanded to all coastal areas in Korea, and it is expected that various engineering applications by performing a persistence analysis of the metocean data.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.2
• /
• pp.127-136
• /
• 2022

This study was conducted to estimate the damage of Whole Crop Maize (WCM) according to abnormal climate using machine learning and present the damage through mapping. The collected WCM data was 3,232. The climate data was collected from the Korea Meteorological Administration's meteorological data open portal. Deep Crossing is used for the machine learning model. The damage was calculated using climate data from the Automated Synoptic Observing System (95 sites) by machine learning. The damage was calculated by difference between the Dry matter yield (DMY)_normal and DMY_abnormal. The normal climate was set as the 40-year of climate data according to the year of WCM data (1978~2017). The level of abnormal climate was set as a multiple of the standard deviation applying the World Meteorological Organization(WMO) standard. The DMY_normal was ranged from 13,845~19,347 kg/ha. The damage of WCM was differed according to region and level of abnormal climate and ranged from -305 to 310, -54 to 89, and -610 to 813 kg/ha bnormal temperature, precipitation, and wind speed, respectively. The maximum damage was 310 kg/ha when the abnormal temperature was +2 level (+1.42 ℃), 89 kg/ha when the abnormal precipitation was -2 level (-0.12 mm) and 813 kg/ha when the abnormal wind speed was -2 level (-1.60 m/s). The damage calculated through the WMO method was presented as an mapping using QGIS. When calculating the damage of WCM due to abnormal climate, there was some blank area because there was no data. In order to calculate the damage of blank area, it would be possible to use the automatic weather system (AWS), which provides data from more sites than the automated synoptic observing system (ASOS).

• The KIPS Transactions:PartB
• /
• v.15B no.4
• /
• pp.275-284
• /
• 2008

With increases in recent security requirements, biometric technology such as fingerprints, faces and iris recognitions have been widely used in many applications including door access control, personal authentication for computers, internet banking, automatic teller machines and border-crossing controls. Finger vein recognition uses the unique patterns of finger veins in order to identify individuals at a high level of accuracy. This paper proposes new device and methods for touchless finger vein recognition. This research presents the following five advantages compared to previous works. First, by using a minimal guiding structure for the finger tip, side and the back of finger, we were able to obtain touchless finger vein images without causing much inconvenience to user. Second, by using a hot mirror, which was slanted at the angle of 45 degrees in front of the camera, we were able to reduce the depth of the capturing device. Consequently, it would be possible to use the device in many applications having size limitations such as mobile phones. Third, we used the holistic texture information of the finger veins based on a LBP (Local Binary Pattern) without needing to extract accurate finger vein regions. By using this method, we were able to reduce the effect of non-uniform illumination including shaded and highly saturated areas. Fourth, we enhanced recognition performance by excluding non-finger vein regions. Fifth, when matching the extracted finger vein code with the enrolled one, by using the bit-shift in both the horizontal and vertical directions, we could reduce the authentic variations caused by the translation and rotation of finger. Experimental results showed that the EER (Equal Error Rate) was 0.07423% and the total processing time was 91.4ms.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.6
• /
• pp.97-107
• /
• 2013

On the Staggered Crosswalks, pedestrians cross the crosswalks two times. This method can reduce the cycle, the vehicle delay and the walking distance by increasing the major direction of green time. The safety of pedestrians is also effective. This study suggests the warrant of the facilities of island width and length etc. by considering the road structure and pedestrians. Also this study suggests the standard of the safety through the accident analysis of Staggered crosswalks and General Crosswalks. In the results, accident rate of the Staggered Crosswalks 18.3(100 million vehicle-km) was lower than the accident rate of the General Crosswalks 28.3(100million vehicle-km). By understanding the start point of crossing of the Staggered Crosswalks, the analysis of the location and types of accident suggests the safety zone(spare space). The setting warrants of Staggered Crosswalks are 4 lane over the road and the 2 meter over sidewalk width of island. The minimum length of the Pedestrian island was doubled compared to the crosswalks width. And the maximum length was set by considering the wait time of the pedestrians.

• Journal of Technologic Dentistry
• /
• v.32 no.1
• /
• pp.25-34
• /
• 2010

This study was the study verifying dental technicians' motivation and job satisfaction in Seoul through the positive method as well as its purposes were to investigated the effect of dental technicians manpower supply/demand prospect on motivation, job satisfaction and the effect of other job satisfaction factors on dental technicians motivation and job satisfaction. For then, general characteristics of study objects were classified by sex, married/unmarried, age, career, salary, highest level of education, working place, position and job as well as job satisfaction factors were classified with future supply/demand prospect, future prospect, working hours, working environment and salary. We conducted a frequency analysis, crossing analysis and multi-linear regression analysis about the effect of the classified articles on motivation and job satisfaction. Also, for verifying the relationship of motivation and job satisfaction, we conducted correlation analysis and its result is as followed. First, it showed that the job related with making orthodontic appliance influenced on motivation, among the age, career and job of the general characteristics, and other jobs between working place and job influenced on job satisfaction. Second, the dark future prospect was showed to influence on motivation and job satisfaction highly so we could grasp that negative opinions are included in that. And low-paying was showed to highly influence on job satisfaction s fall so we could grasp the subjective low-salary standard at the present. But we expected that the manpower supply/demand prospect would influence on motivation and job satisfaction but there was little influence. Third, the correlation between motivation and job satisfaction was showed to be somewhat high, motivation had the standard which is above average and job satisfaction had the standard which is below the average. So with a little improving of job satisfaction, it s possible that motivation can be very high. Therefore, in rapidly changing generation, we think that the dental technicians are actively coping with the reality of low-paying and high-working. But it's implying that anxiety for uncertain future was reflected. Furthermore, because institutional strategies for dental technicians' efficient management are insufficient in relation with policies so it's necessary the policy consideration for solve the job-unsatisfying factors actively.

• Journal of Korean Society of Forest Science
• /
• v.101 no.2
• /
• pp.291-296
• /
• 2012

Triploids are a useful tool for biomass production and molecular breeding of trees with a long life span. Triploids of the poplar 'Hyunsasi' (Populus alba ${\times}$ P. glandulosa) have been developed by crossing between female diploids and a male tetraploid. The tetraploid was developed around the 1970s at Korea Forest Research Institute by colchicine-induced chromosome doubling. Seedlings of the $F_1$ generation were analyzed using flow cytometry to verify their ploidy status. The mean relative fluorescence index of 3 F1 poplars, labeled as Line- 1, Line-17, Line-18, were approximately 1.5 times higher than those of diploid poplars, and the results clearly indicated that they were triploids. The phenotype of the F1 poplars included larger leaves and thicker stem than diploids, and abnormal leaf morphology, especially in the triploid 'Line-18'. Three triploid lines developed roots more slowly and had less roots than diploid. However, 3 poplar cytotypes (2x, Line-1, Line-17) rooted within 10 days on MS medium. In contrast, compared with the 3 cytotypes, the Line-18 showed about 80% and 70% in the rooting rate and the number of roots. The triploid poplars could be directly utilized for biomass production and with their sterility, they could serve as basic material for genetic transformation. In addition, flow cytometric analysis proved to be an effective and reliable method for screening forest trees for their ploidy level.