• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.96-103
• /
• 2006

To establish of standard technique of nano-length measurement in 2D plane, new AFM system has been designed. In the long range (about several tens of ${\mu}m$), measurement uncertainty is dominantly affected by the Abbe error of XY scanning stage. No linear stage is perfectly straight; in other words, every scanning stage is subject to tilting, pitch and yaw motion. In this paper, an AFM system with minimum offset of XY sensing is designed. And XY scanning stage is designed to minimize rotation angle because Abbe errors occur through the multiply of offset and rotation angle. To minimize the rotation angle optimal design has performed by maximizing the stiffness ratio of motion direction to the parasitic motion direction of each stage. This paper describes the design scheme of full AFM system, especially about XY stage. Full range of fabricated XY scanner is $100{\mu}m\times100{\mu}m$. And tilting, pitch and yaw motion are measured by autocollimator to evaluate the performance of XY stage. As a result, XY scanner can have good performance. Using this AFM system, 3um pitch specimen was measured. The uncertainty of total system has been evaluated. X and Y direction performance is different. X-direction measuring performance is better. So to evaluate only ID pitch length, X-direction scanning is preferable. Its expanded uncertainty(k=2) is $\sqrt{(3.96)^2+(4.10\times10^{-5}{\times}p)^2}$ measured length in nm.

• Education of Primary School Mathematics
• /
• v.20 no.2
• /
• pp.163-175
• /
• 2017

The purpose of the study is to identify the effect of length and right angle indication on the understanding of the concept of the figure when presenting the task of classifying the plane figures. we recorded thirty three 4th grade students' performance with eye-tracking technologies and analyzed the correct answer rate and gaze duration. The findings from the study were as follows. First, correctness rate increased and Gaze duration decreased by marking length in isosceles triangle and equilateral triangle. Second, correctness rate increased and Gaze duration decreased by marking right angle in acute angle triangle and obtuse triangle. Based on these results, it is necessary to focus on measuring the understanding of the concept of the figure rather than measuring the students' ability to measure by expressing the length and angle when presenting the task of classifying the plane figures.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.2
• /
• pp.74-80
• /
• 2005

A new dimension measuring method for the measurement of diameter of an object has been developed using laser triangulation. The 3D data of an object was calculated from the 2 dimensional image information obtained by the laser stripe using the laser triangulation. The system that use existing theory can measure the diameter of hole not only in a normal plane but also ill an incline plane. However, in the existing theory, since the lens with fixed feral length was used, the area of measurement was fixed. The simplest way to solve this problem is to change distance between a CCD camera and object. Other way is to use a zoom lens having variable focal length. In this paper, the zoom lens with variable focal length was used. Therefore, we ran experiment with magnification that is optimized according to size of object using zoom lens with variable focal length.

• Fashion & Textile Research Journal
• /
• v.15 no.2
• /
• pp.309-315
• /
• 2013

This study examines the difference of surface properties according to napping characteristic of artificial suedes, measuring surface structure observation, the contact/non-contact method roughness, warm-cool feeling of touch, and subjective hand evaluation. Surface and cross-section observations showed a discernible difference in fineness, curl, length, mount of napping, and covering power of base fabric. The surface properties of artificial suede evaluated by KES-FB4 showed that the shorter napping length the more smooth surface and the roughness increased reciprocally with friction resistance and surface contour when the nap length reaches a high level. The surface roughness measuring system applied a laser displacement sensor by a non-contact method to assess napping characteristic and the base fabric and napping height. Surface roughness decreased when napping was uniformly covered with base fabric; however, the surface roughness increased specifically with the uneven covering power of the base fabric. For qmax of the suedes, those that had short and smaller amounts of napping increased; however, the napping of length and amount at some stage generated a low qmax value. The warm sensation in all suedes were strongly perceived, but the cool sensation of the perception was lower in the subjective evaluation. Smoothness and softness were perceived when the suede has a long and large amount napping; however, smoothness and hardness were perceived when the suede was short and with the uneven covering power.

• Journal of the Korean Society of Radiology
• /
• v.9 no.6
• /
• pp.349-356
• /
• 2015

The study is to recognize the interactions with bone ages by measuring the length between the end of the bone and the growth plate on selected highest weight of regions of seven for bone maturity in TW3 method. The experiment is subjected on seventy-two children (36 males, 36 females) who have examined the growth plate test from March, 2014 to March, 2015 and implemented a regression analysis by measuring the length between the end of the bone and the growth plate in Hand AP image of the children. In result, each bone age has produced a mean value and a standard deviation corresponding to the specific range and as bone age increases the length between the end of the bone and the growth plate decreased. In addition, female children showed lower mean value in comparison to male and also the measurement of the length between the end of the bone and the growth plate and its bone age are shown to be statistically valid(p<0.001) according to the results of regression analysis using its result value. Therefore, the probability of prediction on the bone age read off through the applied TW3 method and regression equation in the Hand AP image of the children.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.10
• /
• pp.2391-2397
• /
• 1993

The distribution of fatigue crack growth rate is influenced by the measuring interval and methods of calculation of crack growth rate. The purpose of this paper is to suggest a method for the evaluation of crack growth rate distribution without the influence. The constant ${\Delta}P$ test and the constant .DELTA.K test are executed by using the CT specimen. The measuring interval of (${\Delta}a$/W=0.0067~0.014) crack length is not affected by methods of the calculation of the fatigue crack growth rate is suggested.

• Journal of ILASS-Korea
• /
• v.7 no.4
• /
• pp.9-15
• /
• 2002

Convolution Fourier transformation tomographically reconstructs the spatially resolved spray injection rate from direct measuring cells. Asymmetric sprays generated from a twin-hole air shroud injector are tested with 12 equiangular projections of measurements. For each projection angle, line of sight integrated injection rate was measured at 35 positions with equal spacing measuring cells of 3 mm in width, 100 mm in length, 55 mm in depth and 0.5 mm thickness of separating wall. Interpolated data between the projection angles effectively increase the number of projections, which significantly enhances the signal-to-noise level in the reconstructed data. This modified convolution Fourier transformation scheme predicts well the structure of asymmetric sprays. Comparative study has been made between sprays with and without air shrouding. Tomograhpic reconstruction of injection rate from direct measuring cells obtained can be used to estimate the accuracy of volume fraction of spray from the LDPA tomographic reconstruction.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.1139-1143
• /
• 1991

Using industrial robots and sensors, we developed an inline car body inspection system which proposes high flexibility and sufficient accuracy. Car Body Inspection(CBI) cell consists of two industrial robots, two corresponding carriages, camera vision system, a process computer with multi-tasking ability and several LDS's. As industrial robots guarantee sufficient repeatabilities, the CBI cell adopts the concept of relative measurement instead of that of absolute measurement. By comparing the actual measured data with reference data, the dimensional errors of the corresponding points can be calculated. The length of the robot arms changes according to ambient temperature and it affects the measuring accuracy. To compensate this error, a robot arm calibration process was realized. By measuring a reference jig, the differential changes of the robot arms due to temperature fluctuation can be calculated and compensated.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.53-54
• /
• 2005

This paper describes that send some signal from encoder attached to crankshaft of marine-engine to measuring instrument using power line modem(PLM) and display cylinder pressure, rpm and etc. on LCD. Conventional method that sends signal along the long signal line has some inconvenience from too long signal line length caused by huge volume of ship's engine. Power line modem can have short signal line from outlets to measuring instrument. Because it use exist power line for send signals, so it have low installation cost and could have good merits in job sites. Through this experiment, pressure in cylinder, engine rpm and etc. signals through PLM are well recognized at measuring instrument.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.251-257
• /
• 1998

The distribution of fatigue crack growth rate is subjected to the measuring interval and calculated method of growth rate. In this paper, in order to establish the method of determining the distribution of fatigue crack growth rate, which ignores those influences, a series of fatigue crack growth experiments and measuring intervals of crack length calculated reasonable are presented. The main conclusions obtained are summarized as follows: 1) As a result of the ΔP constant test and ΔK constant test, it is thought that an approximate measuring interval of 0.3~0.7mm is reasonable, which allows for few errors and is little subjected to the calculated method of crack growth rate.