• 대한의용생체공학회:의공학회지
• /
• 제23권4호
• /
• pp.263-268
• /
• 2002

내시경 영상의 질을 결정하는데는 많은 요소들 즉 내시경 영상가이드가 포함하고 있는 광섬유들의 숫자 및 광섬유 각각의 형태, 재료, 길이 등의 측정, 분석이 필요하지만 그 각각의 요소들은 서로 상관관계를 가지고 있기 때문에 각 요소들에 대한 독립적 분석은 불가능한 것으로 평가되어 지고 있다. 그래서 크게 2가지 특성 즉 영상가이드의 영상분해능(image resolution)과 영상광도(image brightness)를 측정, 분석함으로써 내시경 영상의 질을 판단하려는 연구가 진행되고 있으나 아직 그 정확한 분석 방법이 확립되어 있지 않은 실정이다. 본 연구에서는 의료용 내시경에 사용되는 미세 영상가이드의 영상광도를 정량화하기 위해서 영상가이드 자체의 PF(Packing fraction), 개구수(numerical aperture) 및 광감쇠율의 측정방법을 개발하였고, 실제 미세내시경에 사용되고 있는 영상가이드의 광도를 측정하고 정량화였다 특히 영상가이드 전체의 개구수를 측정함으로써 기존의 개구수 계산값에 의한 방법보다 정확한 영상광도의 정량화가 가능하였고 그 결과 직경이 $3.1\mu m$인 광섬유를 포함하는 영상가이드의 광도는 직경이 $4.1\mu m$인 광섬유를 포함하는 영상가이드 보다 약 37% 만큼 낮다는 결론을 얻었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제13권2호통권54호
• /
• pp.129-136
• /
• 2009

이 연구에서는 사장교의 시공 중 장력보정을 위한 최적 변위계측 위치(OLD) 결정법을 제안한다. 변위 민감도를 구하여 Fisher Information Matrix(FIM)를 정식화하였고, 이를 이용한 유효독립분포벡터(EIDV)를 계산하여 최적 변위계측 위치의 우선순위를 결정하였다. 결정된 최적 변위계측 위치의 효율성과 신뢰성을 검증하기 위하여 사장교에 대한 수치예제를 수행하였다. 변위를 사용한 FIM을 정식화하여 이의 결과를 변위 민감도를 사용한 결과와 수치예제를 통해 비교하였다. 또한 변위 측정오차와 케이블 길이오차가 장력 보정에 미치는 영향을 Monte Carlo 기법을 사용하여 통계적으로 분석하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제14권3호
• /
• pp.9-12
• /
• 2012

Usually, the AC loss from the superconducting element of an SFCL due to the load current is very small because it is composed of the combination of bifilar windings with very small reactance. Although the AC loss is small enough, we should be albe to predict for the design and control of the cryogenic system. In fact, an SFCL for the transmission voltage class may not generate ignorable AC loss because of the inevitable space between the HTS wires for the high voltage insulation and cryogenic efficiency. To measure the AC loss dependency on the space between the 2G HTS wires with the width of 4.4 mm, we prepared an experimental setup which could adjust the distance between the wires. We used two 500-mm length HTS wires in parallel and applied the current in the opposite direction for each wire to simulate a part of a current limiting module for a high voltage SFCL. We also put two couples of voltage taps at the ends of each wire and a cancel coil in the voltage measurement circuit to compensate the reactive component from the voltage taps. In this condition, we varied the distance between the wires to investigate the change of the transport current loss. A similar experimental study with HTS wire with the width of 12 mm is now in progress.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제35권4호
• /
• pp.240-247
• /
• 2009

Purpose: The purpose of this study was to evaluate marginal bone loss to the bone crest functionally loaded for up to eighteen months and also with regard to other variables of interest. Material and Methods: 135 endosseous implants(GS II, Osstem, South Korea) were placed in 35 patients. The design of GS II implant is straight with the microthread. Radiographic examinations were conducted at baseline (implant loading) and 3, 6, 9, 12 and 18 months after loading. Marginal bone level measurement was made from the reference point to the lowest observed point of contact of the marginal bone with the fixture. The reference point of the fixture was the border between the blasted surface and machined surface of the fixture. Results: Implants were on function for a mean 12.7 months(range, 3?18 months). For the 56 maxillary and 79 mandibular implants, mean marginal bone loss was 0.68 mm and 0.70 mm. Implants placed maxillary posterior area displayed more crestal bone loss than the other position. The difference between mesial and distal bone levels was statistically significant (p<0.05) with respective means of 0.51 mm and 0.62 mm. Also, The difference between bone graft group and no-bone graft group was statistically significant(p<0.05) with respective means of 0.38 mm and 0.66 mm. But no statistically significant influence of sex, type of surgery(one or two stage surgery), the implant length was observed(p>0.05). Conclusion: This study indicates the amount of marginal bone loss around implant has maintained a relative stable during follow-up periods.

• 대한치과보철학회지
• /
• 제44권4호
• /
• pp.477-487
• /
• 2006

Purpose : this study was to evaluate the fitness of adjustable dental impression trays on the Koreans : the trays used in the previous study by Kim et al. as part of the dental adjustable tray development project were improved and modified. Material and method: The patterns of tray were made through CAD-CAM process, and a simple silicone-base molds were made from them. The trial products were reproduced by pouring polyurethane into these molds. 30 male students(Wonkwang University, Dental College) and 30 female students (Wonkwang Health Science College, Department of Dental Hygiene) were selected and Reversible hydrocolloid impression materials were used for this study. The fitness of the trays was evaluated by measuring the width and length of impression materials of each measurement sites. Results and conclusion : 1. In adapting the trays inside the mouth, a uniform width of impression material(3 $\sim$ 6mm) was obtained in most sites due to the tooth stops and the inclined planes accommodating the width of the tray 2. The thickness of impression material in the central part of the palate was a mean 9.8mm, which turned out to be somewhat thick. 3. In the mandible. the thickness of the impression material in the lingual side inferior to the contact point of the 1st and 2nd molars was 2.7mm, and the thickness of the material in the lingual side of the rearmost margin was 2.5 mm. The thickness of the impression material of these areas was relatively thin.

• The Journal of Advanced Prosthodontics
• /
• 제11권6호
• /
• pp.331-340
• /
• 2019

PURPOSE. The purpose of this study is to assess the accuracy of three intraoral scanners along the complete dental arch and evaluate the feasibility of the assessment methodology for further in vivo analysis. MATERIALS AND METHODS. A specific measurement pattern was fabricated and measured using a coordinate measuring machine for the assessment of control distances and angles. Afterwards, the pattern was placed and fixed in replica of an upper jaw for their subsequent scans (10 times) using 3 intraoral scanners, namely iTero Element1, Trios 3, and True Definition. 4 reference distances and 5 angles were measured and compared with the controls. Trueness and precision were assessed for each IOS: trueness, as the deviation of the measures from the control ones, while precision, as the dispersion of measurements in each reference parameter. These measurements were carried out using software for analyzing 3-dimensional data. Data analysis software was used for statistical and measurements analysis (α=.05). RESULTS. Significant differences (P<.05) were found depending on the intraoral scanner used. Best trueness values were achieved with iTero Element1 (mean from 10 ± 7 ㎛ to 91 ± 63 ㎛) while the worst values were obtained with Trios3 (mean from 42 ± 23 ㎛ to 174 ± 77 ㎛). Trueness analysis in angle measurements, as well as precision analysis, did not show conclusive results. CONCLUSION. iTero Element1 was more accurate than the current versions of Trios3 and True Definition. Importantly, the proposed methodology is considered reliable for analyzing accuracy in any dental arch length and valid for assessing both trueness and precision in an in vivo study.

• 대한치과기공학회지
• /
• 제38권3호
• /
• pp.127-133
• /
• 2016

Purpose: Currently advanced in Dental CAD/CAM technology increase a use of Co-Cr sinter metal block at Dental CAD/CAM part traditionally it has been being used with metal casting method. There is an advantage that can leave out a step of investment and casting as well as reducing a working time to compare with conventional casting method in a dry milling. Methods: In this research, compare a deformation of before and after sinter result of Co-Cr sinter metal block. Design a specimen figure by 3D CAD software and transformed it to a STL file can be used at Dental CAD/CAM. With a transformed STL file, milled a Co-Cr sinter metal specimen by using a Dental CAD/CAM dry milling machine. It arrived at the following conclusions after measuring an outer form and thickness of a machined specimen and then after sinter measure it again in a way of before sinter measurement method. Results: It is confirmed that there is no error while a 3D design figure specimen is transformed to a Dental CAD data. It is observed that there is no error at Co-Cr sinter metal specimen which consider a length of single coping and bridge. Conclusion: It is observed that there is no deformation at a specimen of AS05 and AB05 are made of 0,5mm thickness. On the other hand, the out of range of deformation is observed at a specimen of AS10 and AB10 which are made of 1mm thickness.

• 전기화학회지
• /
• 제16권4호
• /
• pp.198-203
• /
• 2013

본 실험에서는 MMA와 tBMA의 공중합체를 합성하고, tert-butyl 그룹의 가수분해를 선택적으로 유도하여 poly(MMA-co-MA)를 제조하였다. 또한 말단에 에폭시기를 함유한 다양한 분자량의 PEO와 MA와의 grafting-onto 커플링 반응을 통해 같은 주사슬을 가지지만 부사슬의 길이가 다른 poly(MMA-co-PEGMA)를 합성하여 조성이 이온전도도에 미치는 영향을 평가하였다. AC-impedance로 측정한 상온 이온전도도는 MMA의 몰분율이 82%에서 $5.11{\times}10^{-8}Scm^{-1}$의 값이 얻어진 반면, 48%에서는 $1.88{\times}10^{-6}Scm^{-1}$로서 많은 PEGMA에서 높게 관찰되었다. 또한 에폭시기를 함유한 PEO의 분자량에 따라 이온전도도의 차이가 발생하는데, grafting-onto 법의 입체적 장애가 원인으로 고려되었다. 한편, 합성된 poly(MMA-co-PEGMA) 고분자 전해질은 상온에서 6V까지 우수한 전기화학적 안정성을 보여주었다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권8호
• /
• pp.348-353
• /
• 2003

This paper was the research of high voltage suspension insulator (400 [kN]) including pottery stone, feldspar, clay and alumina of 17 [wt%]. The slurry was fabricated after ball milling mixed raw materials. Green compacts were made by the extrusion of jiggering method and were sintered at 1300[$^{\circ}C$] for 50 [min.] in the tunnel kiln. The sintered density was reached to 97% of theoretical density, and the bending strength was 1658 [k $g_{f}$/$\textrm{cm}^2$] and hardness and fracture toughness which was measured by ICL( indentation crack length ) method were 1658 (kgf/$\textrm{cm}^2$) and 27.5 [Gpa], respectively. In measurement of tana and insulation break voltage of 400 (kN) porcelain, tan$\delta$ took some numerical value between 17${\times}$10$_{-3}$ and 61${\times}$10$_{-3}$ and insulation break voltage value was 19.9$\pm$1.4 [㎸/mm]. The test was performed to research whether the shape of pin affect a overvoltage break load or not As a consequence, when a pin was designed a pin diameter 51 [mm] with the bottom form of two-step constructed with straight in the suspension insulator, Insulator showed overvoltage break load 52 [ton] of the highest value and reflected a fine characteristic in aged deterioration test which is one of the accelerated aging test. Also it could be confirmed a fine characteristic through performing the test that electrical property of insulator was established correctly in accordance with IEC 60383-1 standards.s.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1999년도 춘계학술발표회요약집
• /
• pp.104-104
• /
• 1999

The local heat transfer coefficient is experimentally investigated for the reflux condensation in a countercurrent flow between the steam-air mixture and the condensate. A single vertical tube has a geometry which is a length of 2.4m, inner diameter of 16.56mm and outer diameter of 19.05mm and is made of stainless steel. Air is used as a noncondensible gas. The secondary side is installed in the form of coolant block around vertical tube and the heat by primary condensation is transferred to the coolant water. The local temperatures are measured at 15 locations in the vertical direction and each location has 3 measurement points in the radial direction, which are installed at the tube center, at the outer wall and at the coolant side. In three different pressures, the 27 sets of data are obtained in the range of inlet steam flow rate 1.348 -3.282kg/hr, of inlet air mass fraction 11.8 -55.0%. The local heat transfer coefficient increases as the increase of inlet steam flow rate and decreases as the decrease of inlet air mass fraction. As an increase of the system pressure, the active condensing region is contracted and the heat transfer capability in this region is magnified. The empirical correlation is developed represented with the 165 sets of local heat transfer data. As a result, the Jacob number and film Reynolds number are dominant parameters to govern the local heat transfer coefficient. The rms error is 17. 7% between the results by the experiment and by the correlation.