• 보존과학회지
• /
• 제28권1호
• /
• pp.29-37
• /
• 2012

이 연구는 매장상태에서 출토되는 금동유물의 표면색이 고유한 금색 이외에 붉은 계열의 색들과 교반되어 나타나는 원인을 규명하고자 수은아말감도금법을 재현해 보고 완성품에 대하여 열처리 조건을 변화시켜 도금층의 표면색과 표면 및 단면의 상태변화를 알아보고자 하였다. 그 결과 높은 열처리 실험조건 일수록 도금층에 검은 산화물층이 넓게 생성되었으며, 산화물층을 제거한 부분에서는 붉은색의 도금 표면색이 표출되었다. 또한 표면이 노란색과 붉은색으로 교반된 시료의 미세 표면관찰에서는 색상에 따라 표면상태의 변화양상이 다르게 나타났으며 단면에서는 도금층 공극의 밀도와 크기가 점차 커지는 것으로 밝혀졌다. 열처리 실험 후 표면성분분석 결과 온도가 올라갈수록 Hg와 Au의 비율은 감소하였으나 Cu의 성분비는 증가하였다. 또한 단면분석 결과에서도 실험조건에 따른 층위별 Au와 Cu의 성분변화가 반비례하는 경향을 보였다. 이러한 실험결과들을 볼 때 아말감을 이용한 금동유물은 생산과정이나 생산 이후에 열이 도금층의 표면색에 영향을 미치는 것을 의미하며 도금층 상태에도 관계된다는 것을 확인할 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.128-134
• /
• 2014

A Experimental study on frequency characteristics of the microphone array covered with Kevlar in closed test section wind tunnel. Microphones that are flush mounted in a closed test section wall of wind tunnel are subject to very high flow noise resulting from the turbulence in the wall boundary layer. At this time the microphones measure the strong hydrodynamic fluctuations generated by the flow. The phenomena are referred to a microphone self-noise and a method for reducing this has studied. In this paper the array that covered with acoustically transparent Kevlar sheet was designed and made to reduce the flow-induced self-noise. For the validation frequency characteristics of the Kevlar, the microphone array was installed on the wall and test was performed for white noise and sine wave of several frequencies using loudspeaker. In addition, the paper compared the signals as a tension of Kevlar. The results were presented that tend to decrease the sound pressure level at high frequency above 3500Hz according to existence of Kevlar.

• Nuclear Engineering and Technology
• /
• 제21권4호
• /
• pp.332-340
• /
• 1989

핵연료의 로내 연소거동 분석평가 연구의 일환으로 가압경수로에서 3주기동안 연소한 14$\times$14 사용후 핵연료를 핫셀에서 파괴시험하여 다음과 같은 결과를 얻었다. 1) 고연소 부위의 연료중심에서도 핵연료의 결정립성장은 일어나지 않았다. 2) 연소도 증가에 따라 밀도감소가 일어나 36,000 MWD/MTU 연소도에서는 연료의 밀도가 94.4% TD까지 감소하였다. 3) 피복관의 평균 산화층두께는 연료봉의 중간 및 하부부위에서는 10$\mu$m이하였으나 상부부 위 에서는 급격하게 20$\mu$m이 상으로 증가되었다. 4) 피복관의 수소화물 생성량은 피복관의 산화물 생성량가 연동되어 연료봉 하부보다는 상부에서는 생성량이 많았다.

• Journal of Welding and Joining
• /
• 제35권3호
• /
• pp.28-34
• /
• 2017

The authors derived the criteria on the process parameters of laser depositions with metal powers(SUS316L & IN718) by evaluating the surface and cross-section properties of the deposition layers. The surface characteristics of the deposition layer are investigated through optical microscopy by controlling the process parameters of laser output, powder feeding rate and gas feeding rate. The cross-section characteristics were also analyzed after polishing and chemical etching process. As the gas feeding rate increased, the amount of powder loss increased and the difference in the dilution ratio and heat affected zone depending on laser outputs was observed. In addition, the powder feeding rate used in the experiment did not interfere with the energy absorption of the base material.

• ETRI Journal
• /
• 제44권4호
• /
• pp.543-559
• /
• 2022

To determine a suitable waveform for Internet of Things (IoT) transmission over low-Earth orbit (LEO) satellites, this paper reports the results of a performance comparison between chirp spread spectrum (CSS)-based LoRa and direct sequence spread spectrum (DSSS)-based Ingenu. The performance of both waveforms was measured in terms of the packet error rate, throughput, and packet loss rate, considering the Doppler effect caused by the high speed of LEO satellites and the interference among multiple terminals. Simulation results indicate that the DSSS scheme is more suitable than the CSS scheme for high-traffic IoT services because of its robustness against interference among multiple terminals. However, the CSS scheme is more suitable than the DSSS scheme for high-mobility IoT services because of its robustness against the Doppler effect. We discuss various solutions, such as the preprocessing of Doppler effect and avoidance of packet collision, to enhance the performance of the DSSS and CSS schemes. The simulation results of the proposed solution show that the enhanced DSSS scheme can be a proper waveform in IoT transmission over LEO satellites for both the high-traffic and high-mobility services.

• 한국도로학회논문집
• /
• 제11권2호
• /
• pp.121-132
• /
• 2009

본 연구에서는 노후 콘크리트 포장의 효율적 유지보수를 위하여 국내 최초 적용된 Thin Bonded Continuously Reinforced Concrete Overlay (CRCO) 공법의 초기 공용성이 평가되었다. 서해안 고속도로의 표층 파손 구간에 Jointed Plain Concrete Pavement (JPCP) 덧씌우기와 CR8O 공법을 이용한 보수가 진행되었다. JPCP 덧씌우기 공법이 적용된 구간에서는 인접 슬래브가 완전히 분리되도록 덧씌워진 층의 줄눈을 완전히 커팅하였으며, CRCO 공법이 적용된 구간에서는 0.5% 종방향 철근과 위치 고정용 횡방향 철근을 설치한 후 그 위에 덧씌우기를 수행하였다. 두 구간 모두에서 3종시멘트가 이용되었다. 현장 강도 시험 결과, 1$\sim$3일 내에 교통개방이 가능한강도가 발현된 것이 확인되었으며, vibrating wire gauge (VWG) 데이터 분석 결과 CRCO 공법이 기존 포장의 줄눈 거동을 억제하는 것으로 나타났다. 부착강도 시험결과, 재령에 상관없이 높은 부착강도가 확인되었다. 한편 JPCP 덧씌우기 공법이 적용된 구간에서는 중앙부에서, CRCO 공법이 적용된 구간에서는 CRCO 포장과 같은 무작위 횡방향 균열이 관찰되었으며, CRCO 공법의 균열폭 거동이 JCP 보다 50% 정도 낮은 것으로 나타났다.

• Corrosion Science and Technology
• /
• 제7권1호
• /
• pp.50-60
• /
• 2008

The majority of the described experimental results deal with relatively pure aluminium. Variations were made in the pretreatment of the aluminum substrates and an investigation was performed on the resulting changes in oxide layer composition and chemistry. Subsequently, the bonding behavior of the surfaces was investigated by using model adhesion molecules. These molecules were chosen to represent the bonding functionality of an organic polymer. They were applied onto the pretreated surfaces as a monolayer and the bonding behavior was studied using infrared reflection absorption spectroscopy. A direct and clear relation was found between the hydroxyl fraction on the oxide surfaces and the amount of molecules that subsequently bonded to the surface. Moreover, it was found that most bonds between the oxide surface and organic functional groups are not stable in the presence of water. The best performance was obtained using molecules, which are capable of chemisorption with the oxide surface. Finally, it was found that freshly prepared relatively pure aluminum substrates, which are left in air, rapidly lose their bonding capacity towards organic functional groups. This can be attributed to the adsorption of contamination and water to the oxide surface. In addition the adhesion of a typical epoxy-coated aluminum system was investigated during exposure to water at different temperatures. The coating was found to quite rapidly lose its adhesion upon exposure to water. This rapid loss of adhesion corresponds well with the data where it was demonstrated that the studied epoxy coating only bonds through physisorptive hydrogen bonding, these bonds not being stable in the presence of water. After the initial loss the adhesion of the coating was however found to recover again and even exceeded the adhesion prior to exposure. The improvement could be ascribed to the growth of a thin oxyhydroxide layer on the aluminum substrate, which forms a new, water-stable and stronger bond with the epoxy coating. Two routes for improvement of adhesion are finally decribed including an interphasial polymeric thin layer and a treatment in boiling water of the substrate before coating takes place. The adhesion properties were finely also studied as a function of the Mg content of the alloys. It was shown that an enrichment of Mg in the oxide could take place when Mg containing alloys are heat-treated. It is expected that for these alloys the (hydr)oxide fraction also depends on the pre-treatment and on the distribution of magnesium as compared to the aluminium hydroxides, with a direct impact on adhesive properties.

• 한국정밀공학회지
• /
• 제23권11호
• /
• pp.116-125
• /
• 2006

MEMS and LIGA technologies have been used for fabricating microstructures, but their shape is not 3D because of difficulty for preparation of many masks. To fabricate 3D microstructures, microstereolithography technology based on Digital Micromirror Device($DMD^{TM}$) was introduced. It has no need of masks and is capable of fabricating high aspect ratio microstructures. In this technology, STL file is the standard format as the same of conventional rapid prototyping system, and 3D parts are fabricated by layer-by-layer according to 2D section sliced from STL file. The UV light source is illuminated to DMD which makes bitmap images of 2D section, and they are transferred and focused on resin surface. In this paper, we addressed optical design of microstereolithography system in consideration of light path according to DMD operation and image-forming on the resin surface using optical design program. To verify the performance of implemented microstereolithography system, 3D microstructures with complexity and high aspect ratio were fabricated.

• 한국환경생태학회지
• /
• 제18권3호
• /
• pp.279-287
• /
• 2004

낙동정맥의 가지산～능동산 구간 능선부 주변의 식생구조를 파악하기 위하여 10개 조사지에 50개 조사구를 설치하여 조사를 실시하였다. Ordination기법 중 DCA 분석을 실시한 결과 군락의 종조성이 유사하여 연속적으로 나타났다. 각 조사지별로 식생구조를 분석한 결과 능선부의 주요 식생은 교목층에서 떡갈나무, 소나무 신갈나무이고 아교목층에서는 철쭉꽃, 관목층에서는 미역줄나무였다. 단위면적당(500㎥) 종다양도는 1.5315～2.4005였으며, 연륜분석결과 약 30～40년생 숲으로 밝혀졌다.

• 대한기계학회논문집B
• /
• 제27권5호
• /
• pp.644-654
• /
• 2003

An analytical solution for a vertically stratified viscous flow in a microchannel with a rectangular cross-section is constructed, assuming fully developed laminar flow where the interfaces between the fluid layers are flat. Although the solution is for n-layer flow, restricted results to symmetrical three-layer flow are presented to investigate the effects of the viscosity and thickness ratios of the fluid layers and the aspect ratio of the microchannel on the flow field. Relations between the flow rate and thickness ratios of the fluid layers with varying viscosity distributions are found, considering the cross -sectional velocity profiles which vary noticeably with the three parameters and differ significantly from the velocity profiles of the flow between infinite parallel plates. Interfacial instability induced by the viscosity stratification in the microchannel is discussed referring to previous studies on the instability analysis for plane multilayer flow. Exact solution derived in the present study can be used for examining a diffusion process and three -dimensional stability analysis. More works are needed to formulate the equations including the effects of interfacial' tension between immiscible liquids and surface wettability which are important in microscale transport phenomena.