• Journal of Korean Neurosurgical Society
• /
• v.46 no.2
• /
• pp.144-151
• /
• 2009

Objective: To compare two testing protocols for evaluating range of motion (ROM) changes in the preloaded cadaveric spines implanted with a mobile core type Charite$^{TM}$ lumbar artificial disc. Methods: Using five human cadaveric lumbosacral spines (L2-S2), baseline ROMs were measured with a bending moment of 8 Nm for all motion modes (flexion/extension, lateral bending, and axial rotation) in intact spine. The ROM was tracked using a video-based motion-capturing system. After the Charite$^{TM}$ disc was implanted at the L4-L5 level, the measurement was repeated using two different methods: 1) loading up to 8 Nm with the compressive follower preload as in testing the intact spine (Load control protocol), 2) loading in displacement control until the total ROM of L2-S2 matches that when the intact spine was loaded under load control (Hybrid protocol). The comparison between the data of each protocol was performed. Results: The ROMs of the L4-L5 arthroplasty level were increased in all test modalities (p < 0.05 in bending and rotation) under both load and hybrid protocols. At the adjacent segments, the ROMs were increased in all modes except flexion under load control protocol. Under hybrid protocol, the adjacent segments demonstrated decreased ROMs in all modalities except extension at the inferior segment. Statistical significance between load and hybrid protocols was observed during bending and rotation at the operative and adjacent levels (p< 0.05). Conclusion: In hybrid protocol, the Charite$^{TM}$ disc provided a relatively better restoration of ROM, than in the load control protocol, reproducing clinical observations in terms of motion following surgery.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.6 no.2
• /
• pp.31-38
• /
• 2000

The influence of the genu varum and the genu valgum in two groups of twenty adult man with deformation on hip joint, knee joint, ankle joint is as follows. 1. Each and all, the statistics that measure tibiofemorial angle indicated the group of the genu varum 168 1.42 and the group of the genu valgum 193 2.21, that was more larger or smaller than normal angle 183 of tibiofemorial. The measure Q-Angle(patellofemorial) indicates the group of the genu varum 9 1.5, the genu valgum 19 2.3, that was larger or smaller than normal angle 13. 2. It showed that range of motion hip joint adduction in the group of the genu varum was more larger than normal range of motion hip joint abduction in the group of the genu valgum was more larger than normal range of motion, hip joint internal rotation in the group of the genu valgum was more larger than normal range of motion, hip joint external rotation in the group of the genu varum was more larger than normal range of motion. 3. range of motion knee joint flexion was simillar to two groups of the genu varum and the genu valgum. On tibial tortion of the leg, the group of the genu varum indicated medial tibial tortion, and the genu valgum indicated lateral tibial tortion. 4. Each groups of the genu varum and the genu valgum in plantarflexion and dorsiflexion of ankle joint. With peak angle, the group of the genu varum showed toe-in that was more smaller than normal angle, and the group of the genu valgum showed toe-out that was more larger than normal angle.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1321-1326
• /
• 2011

THE RAILWAY VEHICLE IS CONSISTS OF CARBODY, BOGIE AND WHEELSETS, EACH OF COMPONENTS IS CONNECTED WITH RIGID MASS, SPRING AND DAMPER. EACH OF COMPONENTS HAS TRANSLATION MOTIONS OF LONGITUDINAL (X AXIS), LATERAL (Y AXIS) AND VERTICAL (Z AXIS) DIRECTIONS, ROTATION MOTIONS OF X, Y, Z AXIS WHICH ARE NAMED ROLLING, PITCHING AND YAWING. THE VIBRATION MODE OF RAILWAY VEHICLE IS DIFFICULT TO FIND THE CHARACTERISTICS OF MOTION DURING THE OPERATION ON THE TRACK BECAUSE THESE HAPPEN TO INDEPENDENCE OR DUPLICATION MOTION CAUSED BY VEHICLE, WHEEL/RAIL AND TRACK IRREGULARITY ETC. IT IS NAMED AN ABNORMAL VIBRATION THAT THE VIBRATION, WHICH WAS PASSED THE PRIMARY AND SECONDARY SUSPENSION, IS AFFECTED TO THE PASSENGER WITHOUT DAMPING. THIS PAPER DESCRIBES AN EXPERIENCE EVALUATION TO FIND THE CAUSE OF AN ABNORMAL VIBRATION WHICH WAS HAPPEN AT OPERATING SPEED 60KPH ZONE DURING THE MAINLINE TEST.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.6
• /
• pp.537-545
• /
• 2013

In this paper, the vibration for actuators having lens module, confined to lateral and torsional directions of suspensions, is described by mathematically analyzing its suspension configuration and motion. In order to prove the accuracy of this result, it is compared to a finite element analysis. Also it is shown that modal frequencies can be modified by changing design parameters in mathematical motion expressions.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1995.04a
• /
• pp.45-52
• /
• 1995

The stability and integrity of precast large panel structures are analyzed with nonlinear mathematical model considering the inelastic properties of horizontal joints. In this research, an analysis for cyclic loading test was carried out by the macro model that idealized the horizontal joints as inelastic-nonlinear spring systems. As a results, the strain hardening ratio of shear slip element was estimated as about 0.05%- 0.2% of initial shear stiffness. And under lateral load, the rocking motion due ti overturning moment was dominant rather than shear slip motion in the behavior of precast structures.

• Journal of Ocean Engineering and Technology
• /
• v.13 no.4 s.35
• /
• pp.132-142
• /
• 1999

A three-dimensional linearised potential theory is presented for the prediction of motions and dynamic structural responses of twin-hull ships travelling with forward speed in regular waves. Comparisons between theoretical and experimental results are shown for the motion responses and lateral wave loads of an ASR(anti-submarine rescue) catamaran. In general, good agreement between theory and experiment is found except for some discrepancies that are believed to be caused by neglect of forward speed effects on free surface.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.6
• /
• pp.867-873
• /
• 2011

The transportation of a truss-spar hull from a transport barge of 6000 ton topside module on the spar hull is investigated in the present study. Two possible routes from a fabrication yard in Teeside, England to the Gulf of Mexico are considered in the paper. The results of motion responses of the transport barge obtained from a spectral analysis and the limiting criteria of sea fastening, deck wetness and lateral acceleration are compared and the route selection is discussed. Long-crested waves and short-crested seas as well as the joint probabilities of significant wave heights and wave periods in different sea areas are considered. Generally speaking, the results for long-crested seas are higher than those for short-crested waves.

• Journal of KSNVE
• /
• v.10 no.3
• /
• pp.486-492
• /
• 2000

The major source of railway noises is rolling noise caused by the interaction of the wheels and rails. This rolling noise is generated by the roughness of the wheel /rail surface on tangent track in the absence of discontinuities such as wheel flats or rail joints. These roughness cause relative vibrations of the wheel and rail at their contact area. The vibrations generated at the contact area are treansmitted through the wheel and rail structures exciting resonances of the wheel and travelling waves in the rail. Then these vibrations radiate noise to the wayside. In this paper we predict the rollingnoise radiated from radial/axial motion of the wheel and vertical/lateral motion of the rail using Remington's analytical model and then compare of the predicted sound pressure and measured one. Although there are some inaccuracy in our prediction. these results show in good agreement between 500 Hz and 3150 Hz.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.771-776
• /
• 2002

Optimal shape of the NFR suspension is studied and developed to improve the dynamic performance and reduce the vibration of the suspension system including a optical head slider. Since accurate position control and stability of the slider motion are highly required in NFR due to the narrower track width and the heavier slider than HDD slider with the low flying height, the dynamic characteristics of the suspension are very important to the mechanical performance of the system. The first natural frequencies in flexural and lateral motion of the suspension are critical factors affecting the dynamics and stability of the flying head, so that the dynamic parameters should be designed properly to avoid an excessive vibration or a crash of the slider on the disk. This paper optimizes the shape of the suspension based on homogenization method in NASTRAN and develops a new suspension shape for NFR system. The suspension is tested on experiment to verify the improvement of the dynamic characteristics.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.5
• /
• pp.414-421
• /
• 2007

This paper presents a engine/brake integrated VDC(Vehicle Dynamic Control) system using neural network algorithm methods for wheel slip and yaw rate control. For stable performance of vehicle, not only is the lateral motion control(wheel slip control) important but the yaw motion control of the vehicle is crucial. The proposed NNPI(Neural Network Proportional-Integral) controller operates at throttle angle to improve the performance of wheel slip. Also, the suggested NNPID controller performs at brake system to improve steering performance. The proposed controller consists of multi-hidden layer neural network structure and PID control strategy for self-learning of gain scheduling. Computer Simulation have been performed to verify the proposed neural network based control scheme of 17 dof vehicle dynamic model which is implemented in MATLAB Simulink.