• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.11-16
• /
• 2002

The production of Portland cement involves maximum use of resources and energy, which leads to destruction of tile ecological environment, raising in serious environmental issues such as acid rain and the greenhouse effect. In order to combat the arising problems associated with Portland cement, it thus is necessary that a non-clinker cement should be developed. In this study, non-clinker cement is produced by blending granulate blast furnace slag with phosphogypsum as main materials, and small amounts of hydrate lime or waste lime as activators. This paper aims to investigate compressive strength according to various condition of mixing ratio, blame, W/C ratio and curing temperature. Compressive strength of non-clinker cement increases continuously according to increase in curing age and blain. Although the compressive strength is fairly comparable to that of OPC in the early curing age, it reaches a higher lever in the later age than that of OPC due to the optimum mixing ratio and the continuous reaction of slag and phosphogypsum. Results obtained from this study have shown that non-clinker cement could be used as a replacement of OPC.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.313-318
• /
• 2000

This paper was to investigate the effect of component material to cause drying shrinkage of concrete. The latin square method was used in analysis of experimental results. The experimental factor was W/C, W/A, F.M and the level was divided into four step and the be analyzed. Compressive strength was mainly dependent in W/C through 90% F-verification. Drying shrinkage was mainly dependent on W/C in warly age through the same method, but not in later age. S/A, F.M did not affect compressive strength and drying shrinkage of concrete in all age.

• Computers and Concrete
• /
• v.6 no.4
• /
• pp.269-280
• /
• 2009

In this paper an experimental study of the influence of hot springs curing upon concrete properties was carried out. The primary variables of the investigation include water-to-binder ratio (W/B), pozzolanic material content and curing condition. Three types of hot springs, in the range $40-90^{\circ}C$, derived from different regions in Taiwan were adopted for laboratory testing of concrete curing. In addition, to compare with the laboratory results, compressive strength and durability of practical concrete were conducted in a tunnel construction site. The experimental results indicate that when concrete comprising pozzolanic materials was cured by a hot spring with high temperature, its compressive strength increased rapidly in the early ages due to high temperature and chloride ions. In the later ages, the trend of strength development decreased obviously and the strength was even lower than that of the standard cured one. The results of durability test show that concrete containing 30-40% Portland cement replacement by pozzolanic materials and with W/B lower than 0.5 was cured in a hot spring environment, then it had sufficient durability to prevent steel corrosion. Similar to the laboratory results, the cast-inplace concrete in a hot spring had a compressive strength growing rapidly at the earlier age and slowly at the later age. The results of electric resistance and permeability tests also show that concrete in a hot spring had higher durability than those cured in air. In addition, there was no neutralization reaction being observed after the 360-day neutralization test. This study demonstrates that the concrete with enough compressive strength and durability is suitable for the cast-in-place structure being used in hot spring areas.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.671-674
• /
• 1999

With increasing content of granulated blase furnace slag in cement, the content of capillary pores in the mortar decreases and later age strength of the concrete. Therefore, this provides greater reserves study is carried out to estimate frost resistance of high-strength concrete specimens with water cement ratios using blast-furnace slag. 1. Blast furnace concrete is comparatively more good frost resistance than normal concrete. 2. As the blast furnace slag increases, the quantity of pores with a radius of more than 30nanometer decreses.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.287-292
• /
• 2001

This paper investigates the properties of high fluidity concrete incorporating lime stone powder and fly ash. Lime stone powder(LSP) and fly ash(FA) contents are varied with. According to test results, as LSP and FA contents increase, fluidity, air content and placeability shows a declining tendency. For the temperature history, both LSP and FA have favorable effects on reducing hydration heat, moreover, LSP reduces hydration heat more than FA. LSP shows undesirable strength loss as its content increases. FA also decreases the strength at early age, but it enhances later age strength. Accordingly LSP is expected to improve the quality at fresh concrete and reduce hydration heat, while it causes strength loss.

• Journal of the Korea Concrete Institute
• /
• v.12 no.6
• /
• pp.23-34
• /
• 2000

This paper reports the effects of curing temperature and aging on the strength and the modulus of elasticity. In oder to determine the strength and the modulus of elasticity with curing temperature and aging, experimental and analytical methods are adopted. The tests of 480 cylinders are carried out for type I, V and V with 15 percent replacement of fly ash cement concretes, which are cured at isothermal conditions of 10, 23, 35 and 5$0^{\circ}C$. and the concrete cylinders are tested at the ages of 1, 3, 7 and 28 days. According to the experimental results, the concrete subjected to high temperature at early ages attaines higher early-age compressive and splitting tensile strength but eventually attaines lower later-age compressive and splitting tensile strength. Even if modulus of elasticity has the same tendency, the variation of modulus of elasticity with curing temperature is smaller than that of compressive strength. Based on these experimental results, the relationships among compressive strength, modulus of elasticity and splitting tensile strength are proposed considering the effects of curing temperature, aging and cement type.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.93-94
• /
• 2012

In this study, prediction of later-age compressive strength of ultra-high strength concrete, based on the accelerated strength of concrete cured in 80℃ warm water was investigated. As a result, the nature of ultra-high strength concrete showed a rapid early strength enhancement, compressive strength using warm water method of 80℃ at 2days is same compressive at 28days using standard curing.

• Advances in concrete construction
• /
• v.15 no.6
• /
• pp.359-376
• /
• 2023

Ultra-high-performance concrete (UHPC) has become an attractive cast-in-place repairing material for existing engineering structures. The present study aims to investigate age-dependent high-early-strength UHPC (HESUHPC) material properties (i.e., compressive strength, elastic modulus, flexural strength, and tensile strength) as well as interfacial shear properties of HESUHPC-normal strength concrete (NSC) composites cured at different season temperatures (i.e., summer, autumn, and winter). The typical temperatures were kept for at least seven days in different seasons from weather forecasting to guarantee an approximately consistent curing and testing condition (i.e., temperature and relative humidity) for specimens at different ages. The HESUHPC material properties are tested through standardized testing methods, and the interfacial bond performance is tested through a bi-surface shear testing method. The test results quantify the positive development of HESUHPC material properties at the early age, and the increasing amplitude decreases from summer to winter. Three-day mechanical properties in winter (with the lowest curing temperature) still gain more than 60% of the 28-day mechanical properties, and the impact of season temperatures becomes small at the later age. The HESUHPC shrinkage mainly occurs at the early age, and the final shrinkage value is not significant. The HESUHPC-NSC interface exhibits sound shear performance, the interface in most specimens does not fail, and most interfacial shear strengths are higher than the NSC-NSC composite. The HESUHPC-NSC composites at the shear failure do not exhibit a large relative slip and present a significant brittleness at the failure. The typical failures are characterized by thin-layer NSC debonding near the interface, and NSC pure shear failure. Two load-slip development patterns, and two types of main crack location are identified for the HESUHPC-NSC composites tested in different ages and seasons. In addition, shear capacity of the HESUHPC-NSC composite develops rapidly at the early age, and the increasing amplitude decreases as the season temperature decreases. This study will promote the HESUHPC application in practical engineering as a cast-in-place repairing material subjected to different natural environments.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.603-606
• /
• 2005

Strength development of low heat portland cement(Type IV) concrete according of addition of fly-ash in high strength range is tested. In this study strength development according to water-binder ratio, strength development according to age, effect of fly ash are tested. This study tests effect of low heat portland cement in high strength range concrete and provide guide line concrete mix design for later study and construction.

• Geomechanics and Engineering
• /
• v.16 no.1
• /
• pp.105-112
• /
• 2018

This paper presents results of a compressive investigation conducted on weathered soil stabilized with ground bottom ash (GBA) and red mud (RM). The effects of water/binder ratio, RM/GBA ratio, chemical activator (NaOH and $Na_2SiO_3$) and curing time on unconfined compressive strength of stabilized soils were examined. The results show that the water/binder ratio of 1.2 is optimum ratio at which the stabilized soils have the maximum compressive strength. For 28 days of curing, the compressive strength of soils stabilized with alkali-activated GBA and RM varies between 1.5 MPa and 4.1 MPa. The addition of GBA, RM and chemical activators enhanced strength development and the rate of strength improvement was more significant at the later age than at the early age. The potential environmental impacts of stabilized soils were also assessed. The chemical property changes of leachate from stabilized soils were analyzed in terms of pH and concentrations of hazardous elements. The observation revealed that the soil mixture with ground bottom ash and red mud proved environmentally safe.