• Journal of Sensor Science and Technology
• /
• v.17 no.5
• /
• pp.329-337
• /
• 2008

Simple, small and portable oxygen sensors were fabricated by tape casting technique. Yttria stabilized zirconia containing cordierite ceramics (YSZC) were used as a porous diffused layer of oxygen in pumping cell. Yttria stabilized zirconia (YSZ) solid electrolyte, YSZC porous diffusion layer and heater-patterned ceramic sheets were prepared by co- firing method. Limit current characteristics and the linear relationship of current to oxygen concentration were observed. Viscosity variation of the slurries both YSZ and YSZC showed a similar behavior, but micro pores in the fired sheet were increased with increasing of the cordierite amount. Molecular diffusion was dominated due to the formation of large pores in porous diffusion layer. The plateau range of limit current in porous-type oxygen sensor was narrow than the one of aperture-type oxygen sensor. However limit current curve was appeared in porous-type oxygen sensor even at the lower applied voltage. The plateau range of limit-current was widen as increasing the thickness of porous diffusion layer of the YSZ containing cordierite. Measuring temperature of $600{\sim}650^{\circ}C$ was recommended for limit-current oxygen sensor. Porous diffusion layer-type oxygen sensor showed faster response than the aperture-type one and was stable up to 30 days running without any crack at interface between the layers.

• Journal of Powder Materials
• /
• v.19 no.1
• /
• pp.13-18
• /
• 2012

This study has been performed on the full density sintering of Fe nanopowder and the surface hardening by plasma ion nitriding. The Fe sintered part was fabricated by pressureless sintering of the Fe nanopowder at $700^{\circ}C$ in which the nanopowder agglomerates were controlled to have 0.5-5 ${\mu}m$ sized agglomerates with 150 nm Fe nanopowders. The green compact with 46% theoretical density(T.D.) showed a homogeneous microstructure with fine pores below 1 ${\mu}m$. After sintering, the powder compact underwent full densification process with above 98%T.D. and uniform nanoscale microstructure. This enhanced sintering is thought to be basically due to the homogeneous microstructure in the green compact in which the large pores are removed by wet-milling. Plasma ion nitriding of the sintered part resulted in the formation of ${\gamma}$'-$Fe_4N$ equilibrium phase with about 12 ${\mu}m$ thickness, leading to the surface hardening of the sintered Fe part. The surface hardness was remarkably increased from 176 $H_v$ for the matrix to 365 $H_v$.

• Nuclear Engineering and Technology
• /
• v.28 no.3
• /
• pp.274-279
• /
• 1996

Diffusion coefficient is a critical parameter for predicting radiological source term(migration rate and flux of radionuclide) through given near field conditions in spent fuel or high level waste repository. The effect of exchangeable cation-$Na^+$ and $Ca^{2+} - on the diffusion of $I^- \;and^3H$ (as HTO) in compacted bentonite was examined using a through-diffusion method. Bentonite material used here was compacted to a density of 1.3 Mg/m$^3$, and Na-bentonite was saturated with a solution of 100 mol NaCl/m$^3$ and Ca-bentonite with 50 $mol\;CaCl_2$/m$^3$. The results show that effective diffusion coefficients are generally higher by a factor of two to five in Ca-than Na-clay. This is attributed to the larger particle size of Ca-compared to Na-bentonite; hence, Ca-bentonite has a greater proportion of relatively large pores, which make a greater contribution to mass transport than small pores. Although the nature of the exchangeable cation affects mass diffusion in compacted bentonite, the effect is small and not likely to influence performance assessment modeling of compacted bentonite-based barriers.

• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.488-495
• /
• 2021

Solid state grain growth (SSCG) is a method of growing large single crystals from seed single crystals by abnormal grain growth in a small-grained matrix. During grain growth, pores are often trapped in the matrix and remain in single crystals. Aerosol deposition (AD) is a method of manufacturing films with almost full density from nano grains by causing high energy collision between substrates and ceramic powders. AD and SSCG are used to grow single crystals with few pores. BaTiO₃ films are coated on (100) SrTiO₃ seeds by AD. To generate grain growth, BaTiO₃ films are heated to 1,300 ℃ and held for 10 h, and entire films are grown as single crystals. The condition of grain growth driving force is ∆G_max < ∆G_c ≤ ∆G_seed. On the other hand, the condition of grain growth driving force in BaTiO₃ AD films heat-treated at 1,100 and 1,200 ℃ is ∆G_c < ∆G_max, and single crystals are not grown.

• Geosystem Engineering
• /
• v.21 no.6
• /
• pp.344-351
• /
• 2018

It is reported that the flooding rate in low permeability sandstones is low and the oil recovery is hard to increase after water breakthrough. Understanding characteristics of waterflood is hence important for the recovery improvement. In this work, flooding tests on low permeability sandstones were conducted. The corresponding flooding characteristics were investigated by means of CT scanning and Nuclear Magnetic Resonance. Effects of irreducible water and different rates were also discussed in detail. Experimental results reveal a piston-like displacement at a low rate in low permeability samples. The saturation profile is steep and almost vertical to the forward direction. The results at a low rate confirm that once water broke through, increasing the flooding rate or flooding time can hardly reduce the remaining oil inside the sample. It is probably due to the high pore-throat ratio proven by rate-controlled mercury. Results also confirm that the presence of initial water enhanced sweep efficiency substantially. On one hand, because water had previously occupied the small pores, the subsequent oil can only invade relatively large pores and became more movable. On the other hand, stable collars can not form due to the steep front, which may suppress the snap-off.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.2
• /
• pp.194-198
• /
• 2001

In order to look for polymeric materials applicable to the oxygen electrode membranes of biosensors, polyurethanes (PUs) were synthesized from poly(butylene succinate) diol (Mn 1150), poly(ethylene glycol) (Mn 200), and 4,4'-methylenebis(cyclohexyl isocyanate). The PUs (Mn 15000-100000) underwent the crystallization and melting transitions in the temperature range of 20-30 $^{\circ}C$ and 90-110 $^{\circ}C$, respectively. The oxygen permeability for the PU membranes prepared by the solution casting method could not be measured since oxygen simply leaked through the membranes with an audible noise. However, when the PUs were blended with carboxylated poly(vinyl chloride) (CPVC), the permeability could be measured. The oxygen permeability coefficient (Po2) of the PU/CPVC $(96}4)$ membranes (6.4 Barrer) was high enough for the application as the electrode membranes. The Po2 decreased dramatically when the CPVC content increased from 4 to 5 wt%, but decreased very slowly and approached to that of CPVC (~0.26 Barrer) when the CPVC content increased further. The scanning electron micrographs of the membranes revealed that the PU membranes were composed of large crystal grains with many pores, but the size of the PU crystal grains and pores decreased progressively with increasing the CPVC content.

• Korean Journal of Metals and Materials
• /
• v.49 no.7
• /
• pp.530-534
• /
• 2011

To analyze the effect of the pore size of graphite in a pore-forming agent, graphite was added to porous ceramics of $Al_2O_3-SiO_2-ZrO_2$ systems. The graphite had 45~75, 100~125, 150~180, and 75~180${\mu}m$ dimensions. The properties of the ceramics, such as apparent porosity, density, dynamic elastic modulus, mechanical strength, and permeability, were investigated. The average pore size increased from 15.35${\mu}m$ to 22.32${\mu}m$ with the increase of the graphite size. The sample with the largest average pore size showed the highest mechanical strength and gas permeability. This was due to the sample with the largest pore size at the same porosity having fewer pores and larger distance between the pores than the sample with the smallest pore size, making cracks less likely to propagate. In addition, the large pore size reduced the repulsive power originating from the drag force between the gas and internal pore walls.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.3
• /
• pp.5-8
• /
• 2006

The effect of annealing time in Metal Organic Deposition(MOD) method was investigated at reduced total pressure. As the total annealing pressure was reduced, the growth rate of YBCO films increased from 0.14nm/sec at atmospheric pressure to 4.2nm/sec at 1 Torr. For the total pres sure of 700, 500, 300, 100, and 1 Torr, the optimal annealing times of 60, 40, 20, 10, 2minutes were found in our experimental conditions. When the an nealing time was short, poor crystallinity or un-reacted phase was obtained. Also, the degradation of YBCO films occurred when exposed longer to the humid ambient at the high annealing temperature. The reduced pressure was found effective to in crease the growth rate and to control the pore size of the YBCO films in MOD method. A fast growth of MOD-YBCO films was realized with high critical current density over $1MA/cm^2$ using reduced pressure annealing. Large pores, usually observed at atmospheric pressure in MOD method, disappeared and also, the number of pores was reduced.

• Geomechanics and Engineering
• /
• v.34 no.5
• /
• pp.473-480
• /
• 2023

Acid rain of soils has a significant impact on mechanical properties. An X-ray diffraction test, scanning electron microscope (SEM) test, laser particle size analysis test, and triaxial unconsolidated undrained (UU) test were carried out in red clay soils with different compaction degrees under the effect of different concentrations of acid. The experiments demonstrated that: the dissolution effect of acid rain on colluvium weakened with the increase in the compacting degree under the condition of certain pH values, i.e., the damage to the structure of red clay soil was relatively light, where the number of newly increased pores in the soil decreased and the agglomeration of soil particles increased; for the same compacting degree, the structural gap decreased, and the agglomeration increased with the increase in the pH value (acidity decreases) of the acid rain; the dissolution rate of Si, Al, Fe, and other elemental minerals and cement in red clay soil was found to be higher under the effect of acid rain, in turn destroying the original structure of the soil body and producing a large number of pores. This is macroscopically expressed as the decrease of the soil cohesion and internal friction angle, thereby reducing the shear strength of the soil body.

• Journal of Powder Materials
• /
• v.30 no.3
• /
• pp.262-267
• /
• 2023

Boron carbide (B₄C) is highly significant in the production of lightweight protective materials when added to aluminum owing to its exceptional mechanical properties. In this study, a method for fabricating Al-B₄C composites using high-energy ball milling and directed energy deposition (DED) is presented. Al-4 wt.% B4C composites were fabricated under 21 different laser conditions to analyze the microstructure and mechanical properties at different values of laser power and scan speeds. The composites fabricated at a laser power of 600 W and the same scan speed exhibited the highest hardness and generated the fewest pores. In contrast, the composites fabricated at a laser power of 1000 W exhibited the lowest hardness and generated a significant number of large pores. This can be explained by the influence of the microstructure on the energy density at different values of laser power.