• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.314-323
• /
• 2010

Recently, granular soils having a large particle size are frequently used as a filling material in the construction of foundation, harbor, dam, and so on. The shear behavior of this granular soil plays a key role in the stability of structures. For example, soil particle crushing occurring at the interface between structure and soil and/or within soil mass can cause the disturbance of ground characteristics and consequently induce an issues in respect of stability of structures. In order to investigate the shear behavior according to an existence and nonexistence of particle crushing, numerical analyses were conducted by using the DEM(Discrete Element Method)-based software program PFC(Particle Flow Code). Using the crushing model and non-crushing model which were created in this study, numerical analyses of ring shear test were conducted and their results were analyzed and compared. In general, landslide and slope stability are accompanied by a large displacement and consequently not only a peak strength but also a residual strength are very important in the analysis of landslide and slope stability. However the direct shear test which has been commonly used in the determination of shear strength parameters has a limitation on displacement therefore the residual strength parameters can not be obtained. The characteristics of residual shear behavior were investigated through the numerical analyses in this study.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.343-358
• /
• 2008

Piles of a bridge pier are connected with a column through a pile cap(footing). Behavior of the pile foundation can be different according to the connection method between piles and the pile cap. This difference causes a change of the design method. Connection methods between pile heads and the pile cap are divided into two groups ; rigid connections and hinge connections. KHBDC(Korea Highway Bridge Design Code) has specified to use rigid connection method for the highway bridge. In the rigid connection method, maximum bending moment of a pile occurs at the pile head and this helps the pile to prevent the excessive displacement. Rigid methods are also good to improve the seismic performance. However some specifications prescribe that conservative results through investigations for both the fixed-head condition and the free-head condition should be reflected in the design. This statement may induce an over-estimated design for the bridge which have very good quality structures with casing covered drilled shafts and the PC-house contained pile cap. Because the assumption of free-head conditions (hinge connections) are unreal for the elevated pile cap system with multiple piles of the long span sea-crossing bridges. On the other hand, elastic displacement method to evaluate the pile reactions under the pile cap is not suitable for this type of bridges due to impractical assumptions. So, full modeling techniques which analyze the superstructure and the substructure simultaneously should be performed. Loads and stress state of the very large diameter drilled shaft and the pile cap for Incheon Bridge which will the longest bridge in Korea were investigated through the full modeling for rigid connection conditions.

• 한국지반공학회논문집
• /
• 제23권10호
• /
• pp.163-174
• /
• 2007

큰 선행하중을 가할 수 있는 새로운 선행하중 시스템을 개발하였으며, 이를 적용하여 근접굴착 시 기존 터널의 안정성을 확보하는 방안을 연구하였다. 흙막이 벽체의 수평변위가 거의 생기지 않도록 설계축력 이상의 선행하중을 가하였다. 이를 위해 선행하중을 가하지 않는 경우와 선행하중을 가하는 경우에 대해 축소율 1/10인 실 대형 시험을 실시하였다. 수치해석은 선행하중을 가하지 않는 경우와, 선행하중을 설계축력의 50%와 100%를 가하는 경우, 흙막이 벽체 변위를 거의 발생시키지 않는 크기의 선행하중을 가하는 경우에 대해 유한요소법(FEM) 프로그램인 PLAXIS를 사용하여 수행하였다. 그 결과 선행하중을 설계축력 이상으로 적용시켜 흙막이 벽체변위를 억제시켰을 때 벽체 배면 지반에 있는 터널의 안정성이 크게 향상되는 것을 확인할 수 있었다.

• Structural Engineering and Mechanics
• /
• 제24권6호
• /
• pp.647-664
• /
• 2006

In this study, an improved finite element formulation with a scheme of solution for the large deflection analysis of inextensible prismatic and nonprismatic slender beams is developed. For this purpose, a three-noded Lagrangian beam-element with two dependent degrees of freedom per node (i.e., the vertical displacement, y, and the actual slope, $dy/ds=sin{\theta}$, where s is the curved coordinate along the deflected beam) is used to derive the element stiffness matrix. The element stiffness matrix in the global xy-coordinate system is achieved by means of coordinate transformation of a highly nonlinear ($6{\times}6$) element matrix in the local sy-coordinate. Because of bending with large curvature, highly nonlinear expressions are developed within the global stiffness matrix. To achieve the solution after specifying the proper loading and boundary conditions, an iterative quasi-linearization technique with successive corrections are employed considering these nonlinear expressions to remain constant during all iterations of the solution. In order to verify the validity and the accuracy of this study, the vertical and the horizontal displacements of prismatic and nonprismatic beams subjected to various cases of loading and boundary conditions are evaluated and compared with analytic solutions and numerical results by available references and the results by ADINA, and excellent agreements were achieved. The main advantage of the present technique is that the solution is directly obtained, i.e., non-incremental approach, using few iterations (3 to 6 iterations) and without the need to split the stiffness matrix into elastic and geometric matrices.

• 한국운동역학회지
• /
• 제13권3호
• /
• pp.81-98
• /
• 2003

The purpose of this study is to closely examine kinematic characteristics by jump phase of Li Xiaopeng motion in horse vaulting and provide the training data. In doing so, as a result of analyzing kinematic variables through 3-dimensional cinematographic using the high-speed video camera to Li Xiaopeng motion first performed at the men's vault competition at the 14th Busan Asian Games, the following conclusion was obtained. 1. It was indicated that at the post-flight, the increase of flight time and height and twisting rotational velocity has a decisive effect on the increase of twist displacement. And Li Xiaopeng motion showed longer flight time and higher flight height than Ropez motion with the same twist displacement of entire movement. Also the rotational displacement of the trunk at peak of COG was much short of $360^{\circ}$(one rotation) but twist displacement showed $606^{\circ}$. Likewise, Li Xiaopeng motion was indicated to concentrate on twist movement in the early flight. 2. It was indicated that at the landing, Li Xiaopeng motion gets the hip to move back, the trunk to stand up and the horizontal velocity of COG to slow down. This is thought to be the performance of sufficient landing, resulting from large security of rotational displacement of airborne and twist displacement. 3. It was indicated that at the board contact, Li Xiaopeng motion made a rapid rotation uprighting the trunk to recover slowing velocity caused by jumping with the horse in the back, and has already twisted the trunk nearly close to $40^{\circ}$ at board contact. Under the premise that elasticity is generated without the change of the feet contacting the board, it will give an aid to the rotation and twist of pre-flight. Thus, in the round-oH phase, the tap of waist according to the fraction and extension of hip joint and arm push is thought to be very important. 4. It was indicated that at the pre-flight, Li Xiaopeng motion showed bigger movement than the techniques of precedented studies rushing to the horse, and overcomes the concern of relatively low power of jump through the rapid rotation of the trunk. Li Xiaopeng motion secured much twist distance, increased rotational distance with the trunk bent forward, resulting in the effect of rushing to the horse. 5. At horse contact, Li Xiaopeng motion makes a short-time contact, and maintains horse take-off angle close to vertical, contributing to the increase of post-flight time and height. This is thought to be resulted from rapid move toward movement direction along with the rotational velocity of trunk rapidly earned prior to horse contact, and little shave of rotation axis according to twist motion because of effective twist in the same direction.

• 지질공학
• /
• 제25권1호
• /
• pp.115-129
• /
• 2015

대단면 터널 입구부의 대절토 사면은 불안정한 응력분포 및 소성변형 가능성으로 인해 잠재적 취약부로 인식되고 있다. 본 사례연구에는 대단면 터널 갱구부 대절토 사면의 강우 후 유실사고 및 원인규명, 복구공법을 분석하여 제시하였다. 대상 현장은 46 mm의 강우 후 암반의 불연속면을 따라 대규모 평면파괴가 발생하였으며, 상부 절토사면의 불안정을 야기하였다. 지질조사 및 매핑 자료 분석 결과, 붕괴 원인은 풍화된 암반의 불연속면에 협재된 충전물과 지반 포화로 인한 절리면 연화(softening)로 판단되었다. 알칼리 장석이 풍부한 화강편마암은 풍화에 취약한 것으로 나타났다. 침하량 계측자료 분석 결과, 붕괴 직전에 급격한 변위량 증가를 관찰하였으며, 향후 사면 계측관리에 활용할 수 있을 것으로 판단된다. 응급복구 대책으로 콘크리트 공동충전 및 외부로부터 압성토 채움을 성공적으로 시행하였다. 항구복구 대책으로 사면부에는 격자블럭 및 지중 앵커 시스템을, 터널 측벽부에는 추가 락볼트 보강 및 그라우팅 공법을 성공적으로 적용하였다. 한계평형해석과 평사투영해석을 통해 원 사면의 불안정성과 보강방법의 유효성을 확인하였다. 본 사례연구는 향후 유사한 대절토 사면에 귀중한 참고자료로 활용될 것으로 기대된다.

• 터널과지하공간
• /
• 제20권1호
• /
• pp.28-38
• /
• 2010

본 연구는 NATM 터널의 천단변위, 내공변위, 숏크리트 응력, 록볼트 축력 등의 현장 계측치를 분석하고, 2D 3D 연속체 수치해석 및 2D 불연속체 불연속면 변형 해석을 실시, 그 결과를 비교 검토하여 각 구간의 시공과정에 따른 전반적인 변위와 거동의 경향성 및 수치해석적 접근의 적용성을 검토하고자 하였다. 그 결과 전단면 굴착 구간(지보패턴 P1~P3)에서 터널의 천단 및 내공변위를 예측하고자 할 시에는 2D 연속체 수치해석만으로도 가능하나, 상 하 반단면 구간(지보패턴 P4~P6)에서 터널의 천단 및 내공변위를 예측하고자 할 시에는 반드시 2D 불연속 수치해석을 수행하여야 한다. 한편, 2D 연속체 수치해석만으로도 전 구간에 대한 터널 내 숏크리트 응력 및 록볼트 축력의 예측이 가능하다. 그리고 시공 단계에 따른 거동 및 경향성을 확인하고자 할 시에는 3D 연속체 수치해석을 수행하여야 하며, 대형 대피소 등의 접속부의 경우도 반드시 3D 연속체 수치해석을 수행하여야 한다.

• 한국지진공학회논문집
• /
• 제11권1호
• /
• pp.1-9
• /
• 2007

본 연구는 지진하중을 받는 콘크리트 표면차수벽형 석괴댐(CFRD)의 정상부 변위에 대한 사력재료 주요물성의 민감도를 정량적으로 분석하는데 그 목적이 있다. 이를 위해 현재 운영 중인 국내 CFRD 형식의 D댐에 대해 2가지 지진파, 각 지진파에 대해 2가지 설계진도, 사력재료에 대해 수행된 대형삼축압축시험 결과로부터 얻어진 물성값을 조합하여 만든 물성값이 다른 해석단면 27개를 작성, 총 108개 해석단면에 대한 동적 수치해석을 수행, 그 결과를 이용한 대역적 민감도분석을 수행하였다. 민감도분석 결과, 지진하중 작용 시 댐 정상부 침하량은 입력지진의 종류와 설계진도 크기에 상관없이 절대적으로 사력재료 전단탄성계수에만 영향을 받았으며 댐 정상부 횡변위의 경우에는, 사력재료 전단탄성계수의 영향이 크나 그 영향의 정도는 침하량에 미치는 정도에 비해 상대적으로 작으며, 침하량과는 달리 지진파의 종류와 크기에 따라 차이를 보였다. 본 연구결과에 한해 사력재료의 마찰각은 지진하중에 의한 CFRD 정상부 변위에는 전혀 영향을 주지 않는 것으로 나타났다.

• Earthquakes and Structures
• /
• 제1권1호
• /
• pp.1-19
• /
• 2010

It has been known that one-dimensional rod theory is very effective as a simplified analytical approach to large scale or complicated structures such as high-rise buildings, in preliminary design stages. It replaces an original structure by a one-dimensional rod which has an equivalent stiffness in terms of global properties. If the structure is composed of distinct constituents of different stiffness such as coupled walls with opening, structural behavior is significantly governed by the local variation of stiffness. This paper proposes an extended version of the rod theory which accounts for the two-dimensional local variation of structural stiffness; viz, variation in the transverse direction as well as longitudinal stiffness distribution. The governing equation for the two-dimensional rod theory is formulated from Hamilton's principle by making use of a displacement function which satisfies continuity conditions across the boundary between the distinct structural components in the transverse direction. Validity of the proposed theory is confirmed by comparison with numerical results of computational tools in the cases of static, free vibration and forced vibration problems for various structures.

• Coupled systems mechanics
• /
• 제1권2호
• /
• pp.165-182
• /
• 2012

Macroscopic hot spots formed due to the large thermal gradients at the surface of the disc brake rotor, make the rotor to fail or wear out early. Thermo-elastic deformation results in contact concentration, leading to the non uniform distribution of temperature making the disc susceptible to hot spot formation. The formation of one hot spot event will predispose the system to future hot spotting at the same location. This leads to the complete thermo-elastic instability in the disc brakes; multitude parameters are responsible for the thermo elastic instability. The predominant factor is the sliding velocity and above a certain sliding velocity the instability of the brake system occurs and hot spots is formed in the surface of the disc brake. Commercial finite element package ABAQUS(R) is used to find the temperature distribution and the result is validated using Rowson's analytical model. A coupled analysis methodology is evolved for the automotive disc brake from the transient thermo-elastic contact analysis. Temperature variation is studied under different sliding speeds within the operation range.