• Journal of Magnetics
• /
• 제18권3호
• /
• pp.260-267
• /
• 2013

In this paper a general 2-D model of a large air-gap synchronous machine either with non-magnetic or magnetic core rotor is investigated and electrical characteristics of the machine are analytically calculated. Considering the general model, analytical equations for magnetic field density in different regions of the large air-gap machine are calculated. In addition, self and mutual inductances in the proposed model of the machine have been developed, which are the most important parameters in the electromagnetic design and transient analysis of synchronous machines. Finite element simulation has also been performed to verify the obtained results from the equations. Analytical results show good agreement with FEM results.

• 전기학회논문지
• /
• 제58권5호
• /
• pp.929-935
• /
• 2009

As modem industrialized society progresses, the demand for electric power is increasing rapidly. The electric power system is getting amazingly bigger and complicated, which can easily induce serious troubles from the potential of large fault problems and/or system failure. The monitoring and diagnosis of the electric machine for the fault detection and protection has been important part in the electric power system. Most faults in the generator appear in the winding. This paper presents the air-gap magnetic flux characteristic of a small-scale 2-pole synchronous generator according to the faults in the field winding to protect the generator from the fault. The magnetic flux patterns in air-gap of a generator under various fault conditions as well as a normal state are simulated by using finite element method. These results are successfully applied to the detection and diagnosis of the short-circuit condition in rotor windings of a high capacitor generator.

• 전기의세계
• /
• 제21권2호
• /
• pp.5-8
• /
• 1972

The purpose of this paper is, as a preliminary step to study on the method of analysing the torque of toothed solid iron rotor, to make an inquiry into the torque calculation formula of homogenious solid iron rotor without slot. The starting point for its theoretical analysis on torque generated by eddy current in solid iron rotor is based on the maximum air gap flux density. In solid rotor induction motor, torque generated by rotor core is considerably large in the range of large slip. The calculated value and observed value on the test machine are also examined in this paper.

• 전기학회논문지
• /
• 제60권12호
• /
• pp.2230-2235
• /
• 2011

The purpose of this paper is to provide the unbalanced magnetic force and vibration mode comparison between two large interior permanent magnet machines(IPM) with different pole-slot combination considering stator and rotor eccentricity. Due to the punching tolerance, the mixed eccentricity of air-gap is inevitable. It will generate the asymmetric magnetic flux density in air-gap, which makes the unbalanced magnetic pull and vibration. The study is focused on the unbalanced magnetic force and their harmonic components according to eccentricity conditions such as static, dynamic and mixed. When the high vibration is produced especially resonance, the obtained results provide clues what eccentricity condition occurs in the machine.

• The Journal of Advanced Prosthodontics
• /
• 제6권1호
• /
• pp.39-45
• /
• 2014

PURPOSE. The aim of the present study was to evaluate the accuracy of three techniques for correction of cast implant bars. MATERIALS AND METHODS. Thirty cast implant bars were fabricated on a metal master model. All cast implant bars were sectioned at 5 mm from the left gold cylinder using a disk of 0.3 mm thickness, and then each group of ten specimens was corrected by gas-air torch soldering, laser welding, and additional casting technique. Three dimensional evaluation including horizontal, vertical, and twisting measurements was based on measurement and comparison of (1) gap distances of the right abutment replica-gold cylinder interface at buccal, distal, lingual side, (2) changes of bar length, and (3) axis angle changes of the right gold cylinders at the step of the post-correction measurements on the three groups with a contact and non-contact coordinate measuring machine. One-way analysis of variance (ANOVA) and paired t-test were performed at the significance level of 5%. RESULTS. Gap distances of the cast implant bars after correction procedure showed no statistically significant difference among groups. Changes in bar length between pre-casting and post-correction measurement were statistically significance among groups. Axis angle changes of the right gold cylinders were not statistically significance among groups. CONCLUSION. There was no statistical significance among three techniques in horizontal, vertical and axial errors. But, gas-air torch soldering technique showed the most consistent and accurate trend in the correction of implant bar error. However, Laser welding technique, showed a large mean and standard deviation in vertical and twisting measurement and might be technique-sensitive method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.24-26
• /
• 2004

The PM(Permanent Magnet) stepping Motor has been used widely to a variety of industries because of the open-loop control characteristic, a relatively large frequency range of velocity control and non-accumulated error of the step angle. Moreover, It has been gradually applied to office automation, machine intelligence, digital appliance, and automobile parts. This paper presents the optimal design results by use of the experimental method. The design variables of the PM stepping motor are shape of the claw-pole, material of core, and air-gap. As a result, a superior claw-pole PM stepping motor for OA machinery was developed.

• Restorative Dentistry and Endodontics
• /
• 제35권5호
• /
• pp.321-334
• /
• 2010

연구목적: 본 연구는 상아질 접착제의 잔류 용매가 접착 효율에 미치는 영향을 평가하고자 하였다. 연구 재료 및 방법: 본 연구에서는 5세대 2단계 산부식형 접착제와 7세대 단일과정 자가부식형 접착제를 사용하였다. 상아질 접착제의 증발률과 전환률, 적용 후 용매의 공기건조 방법에 따른 미세인장결합강도를 측정하였으며 접착 계면을 FE-SEM을 이용하여 관찰하였다. 결과: 1. 시간에 따라 접착제의 증발률은 증가하나 접착제의 종류에 따라 증가 양상이 서로 달랐다. 2. 대부분 전환률은 증발률에 비례하는 경향을 나타내었다. 3. 공기건조 방법에 따라 결합강도는 대부분 under군, control군, over군 순으로 증가하는 양상을 나타내었다. 4. FE-SEM에서 아세톤을 용매로 사용하는 접착제는 공기건조 방법에 따라 droplet이나 gap이 관찰되었다. 결론: 상아질 접착제의 잔류 용매는 접착 효율에 부정적인 영향을 미치기 때문에, 상아질 접착제의 선택과 사용 시 용매의 종류와 특징에 대한 적절한 이해가 필요할 것이다.