• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.185-190
• /
• 2002

It has made a special study of bending behavior of F.R.P sandwich beams with bonded 2nd-reinforced plies. Specimens were made of Chopped Mat 300-450, Roving Clothes 570 and the mixture weight ratio of Resin versus hardener was 55:45 for bending tests. it was fabricated by hand lay-up method, hardened for 24 hours in nature, cut specimens according to ASTM standard C393-94 Knowing exact behavior of bonded area's stress and strain depends upon various bonded F.R.P length on which covered lap joint. We also considered shear stress in adhered area and have done computational estimation by ANSYS as well. This study reveals that the length of plies covered lap joint are longer, Failure stresses are remarkably larger.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.168-171
• /
• 2001

Due to intrinsic load eccentricity, severe peel stress concentration occurs at both ends of the single-lap joint. To avoid load eccentricity as well as the singular tensile peel stress in the joint interface, composite wavy-lap joint is proposed. In this paper, refined 3-D stress analysis of wavy-lap joint is performed by finite element method using parallel mutifrontal solver. Analysis results show that the singular tensile peel stress concentration is totally avoided in wavy-lap joint, and that loads are more evenly transferred over the length of the joint. Therefore, the strength of wavy-lap joint is significantly higher than that of conventional single-lap joint. And it is believed that even higher strengths can be obtained by optimizing the new design configuration.

• 한국지진공학회논문집
• /
• 제16권6호
• /
• pp.47-56
• /
• 2012

It is known that seismic performance of existing bridges having insufficient lateral confinements and lap-splices of longitudinal reinforcements at the base of column decreases dramatically. In this study, small-scaled model tests have been performed to confirm the seismic behaviors of RC bridge piers with various lap-splice lengths. The 8 test models have circular section with diameters of 0.65 m, 0.8 m, 1.0 m, and lap-splice lengths of B-class or C-class. The test results show that the failure modes of models are not depending on the lap-splice length itself but depend on the ratio of lap-splice length to diameter, and that the displacement ductility is also affected by this ratio.

• Composites Research
• /
• 제26권2호
• /
• pp.135-140
• /
• 2013

이 연구에서는 이음부가 초고성능콘크리트 교량 바닥판의 정적 거동에 미치는 영향을 실험적으로 규명하고, 이음부 철근의 최소겹침이음길이를 제안하였다. 총 6개의 실험부재를 제작하였으며 4점 휨 실험에 의하여 성능을 평가하였다. 이음부는 UHPC의 높은 부착특성으로 인하여 단순하면서도 매우 효율적인 구조가 될 것으로 기대되는 철근겹침이음을 대상으로 하였다. 실험결과로부터 이음부의 설치에 의한 UHPC의 인장기여도 감소에 따라 약 30% 수준의 휨강도 감소가 발생되는 것으로 측정되었고, 150 mm 이상의 철근겹침이음길이를 확보하면 연속된 철근을 사용한 경우와 거의 유사한 강도와 연성을 확보할 수 있는 것으로 나타났다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.931-936
• /
• 2003

Lap splices were located in the plastic hinge region of most bridge piers that were constructed before the adoption of the seismic design provision of Korea Highway Design Specification on 1992. Lap splicing is also permitted if hoops or spiral reinforcement are provided over the lap length in the current seismic design provision. But sudden brittle failure of lap splices may occur under inelastic cyclic loading. The purpose of this study is the analytical prediction of nonlinear hysteretic behavior and ductility capacity of reinforced concrete bridge piers with lap splices under cyclic loading. For this purpose, a nonlinear analysis program, RCAHEST(Reinforced Concrete Analysis in Higher Evaluation System Technology) is used. Lap spliced bar element is developed to predict behaviors of lap spliced bar. Maximum bar stress and slip of lap spliced bar is considered.

• Advances in concrete construction
• /
• 제9권1호
• /
• pp.83-92
• /
• 2020

The use of spliced reinforcing bars in sustainable concrete members to manage inadequate bars length is a common practical issue which is may be due to some limitations. The lap splicing means two bars overlapped in parallel with specified length called the splice length in order to provide the required bond between the two bars. The bond between sustainable concrete and spliced steel bars is another important issue. The normal strength sustainable concrete specimens of sizes 1700×150×150 mm with tension reinforcement lap spliced were selected according to testing device length limitations. These members were designed to fail in flexure in order to investigate the lap spliced tension bars effect. The selected lap spliced tension bars were of 10 mm size with smooth and deformed surfaces in order to investigate the surface nature accompanied with the splice nature. The sustainable concrete mechanical properties and mix workability were also studied. This study reveals that the effect of number of spliced bars on the response of beams reinforced with smooth bars is found to be more obvious than deformed one. Finite element modeling in three dimensions was carried out for the tested beams using ABAQUS software. A parametric study is carried out using finite elements on considering the following parameters, concrete compressive strength, load type and opening in cross section (hollow section) for weight reduction purposes.The laboratory and numerical results show good agreements in terms of ultimate load and deflection with an average difference of 10% and 15% in ultimate load and deflection respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권4호
• /
• pp.394-400
• /
• 2007

The properties and weldability of lap joints by PFSW with 1050 Al sheet was investigated according to tool shape. dimension and welding condition. Tensile shear test was carried out for lap jointed specimen, and the hardness in the joint regions was examined. Moreover interfacial joining length, metallograph and failure location of the lap-jointed cross section were discussed. Two tool types were a simple cylindrical type and a notched cylindrical type. Under joining conditions such as plunging depth of 2.2mm. rotating speed of 1600rpm and dwelling time of 3s, the tensile shear strength of lap-jointed specimen by the notched type tool was superior to that by simple cylindrical type tool. The maximum tensile shear load of lap jointed specimen was 5807N. Optimal dimensions of the notched type tool were as follows : diameters of the shoulder and pin were $18{\phi}mm$ and $10{\phi}mm$, and pin length was 2.2mm.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권6호
• /
• pp.76-83
• /
• 2021

본 연구에서는 이음된 초고강도 강섬유보강콘크리트 부재의 휨거동을 검토하고, 현행설계기준의 초고강도 강섬유보강콘크리트 구조물의 이음 설계에 대한 안전성을 평가하기 위해 총 6개의 보에 대한 가력 실험을 수행하였다. 주요 변수는 섬유의 혼입여부와 이음 길이로 설정하였다. 혼입된 섬유는 강섬유로 2%의 부피비로 결정하였으며, 이음길이는 8db와 16db로 결정하여 실험체를 제작하였다. 실험 결과 섬유로 보강되지 않은 실험체들은 이음부에서 급격한 하중지지능력을 상실하고 철근의 항복을 경험하지 못하였으나, 섬유로 보강된 경우 16db의 이음길이가 확보되면 주인장철근의 항복을 경험할 수 있으며, 적절한 휨강도를 발현할 수 있는 것으로 나타났다. 본 연구의 실험결과를 바탕으로 현행설계기준 및 초고강도콘크리트 구조설계지침의 이음길이 산정식들을 검토한 결과 모두 보수적인 평가를 하고 있는 것으로 나타났다.

• Journal of Welding and Joining
• /
• 제19권3호
• /
• pp.342-347
• /
• 2001

Recently, adhesive-bonding technique is wifely used in manufacturing structures. Stress and strain analysis of joints are essential to design adhesive-bonded joints structure. The single-lap adhesive joint is the design dominating the range of adhesive joints. In this study, single-lap specimens with different joint dimensions were used for the tensile-shear test and finite element calculation in of order to investigate the effect of overlap length and adhesive-bonding thickness on adhesive strength and stress distribution of the joints. Consequently, it was found that overlap lap size and thickness can be important parameters of structure joints using adhesive bonding, which is effected on adhesive strength.

• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.905-915
• /
• 1998

Static tensile tests using adhesive-bonded single-lap joints of aluminum alloy were conducted to investigate the effect of geometric factor, overlap length, adherend thickness, adhesive thickness and material composition of adherend/adhesive on the strength of adhesive joint. The average applied shear stress at joint fracture decreased with increasing lap length. However increasing the adherend thickness resulted in a higher joint strength. Higher yield strength of adherend and lower elastic modulus of adhesive is advantageous to the adhesive joint. Newly proposed modified joint factor could be well evaluated the influence of lap length, adherend thickness and adhesive thickness on the bond strength for adhesive joints.