• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.5
• /
• pp.219-225
• /
• 2020

The objective of this study was to investigate the tensile properties and thermal conductivities of Mg9.3%Al alloy in as-cast state and heat-treated state consisting of fully discontinuous precipitates (DPs), respectively. The fully DPs microstructure was obtained by solution treatment at 405℃ for 24 h, followed by furnace cooling to RT. The as-cast alloy showed a partially divorced eutectic β(Mg₁₇Al₁₂) phase particles formed along the α-(Mg) cell boundaries. The DPs had various apparent (α+β) interlamellar spacings, which is related to different transformation temperatures during the furnace cooling. The DPs microstructure exhibited better tensile strength than the as-cast one, resulting from the higher value of elongation in response to its more homogeneous microstructure. It is noticeable that the DPs microstructure had 12.4% higher thermal conductivity in average than the as-cast one between RT and 200℃. The XRD analyses revealed that the lower Al concentration in the α-(Mg) matrix may well be responsible for the better thermal conductivity of the DPs microstructure.

• Journal of Microbiology and Biotechnology
• /
• v.12 no.4
• /
• pp.643-648
• /
• 2002

For wastewater treatment and utilization of the biomass, a photosynthetic bacterium was isolated based on its cell growth rate, cell mass, and assimilating ability of organic acids. The isolate was a Gram-negative rod-shaped bacterium that contained a single polar flagellum and formed a lamellar intracytoplasmic membrane (ICM) system, including bacteriochlorophyll $\alpha$. The major isoprenoid quinone component was identified as ubiquinone Q-10, and the fatty acid composition was characterized as to contain relatively large amount of C-16:0 (18.74%) and C-18:1 (59.23%). Based on its morphology, phototrophic properties, quinone component, and fatty acid composition, the isolate appeared to be closely related to the Rhodopseudomonas subgroup of purple nonsulfur bacteria. A phylogenetic analysis of the isolate using its 16S rRNA gene sequence data also supported the phenotypic findings, and classified the isolate closely related to Rhodopseudomonas palustris. Accordingly, the nomenclature of the isolate was proposed as Rhodopseudomonas palustris KUGB306. A bench-scale photosynthetic bacteria (PSB) reactor using the isolate was designed and operated for the treatment of soybean curd wastewater.

• Journal of Welding and Joining
• /
• v.13 no.3
• /
• pp.106-115
• /
• 1995

To know the bonding phenomena of Ti/Cu brazed joint, a characteristic of microstructures in bonding interlayer of vacuum brazed pure Ti to Cu has been studied in the temperature range from 1088 to 1133K for various bonding times using Ag-28wt%Cu filler metal. Also intermediate phases formed in bonded interlayer and behavior of layer growth have been investigated. The obtained results in this study are as follows: 1) Liquid insert metal width at the each brazing temperature was proportional to the square root of brazing time, and it was considered that the liquid insert metal width was controlled by the diffusion rate process of primary .alpha.-Cu formed at the Ti side. 2) Intermediate phases formed near the Ti interface were .betha.-Ti and intermetallic compounds TiCu, Ti$_{2}$Cu, Ti$_{3}$Cu, and TiCu. 3) .betha.-Ti formed in Ti base metal durig brazing transformed to lamellar structure, .alpha.-Ti + Ti$_{2}$Cu. The structure came from the eutectoil decomposition reaction in cooling. And the width of .betha.-Ti layer was proportional to the square root of brazing time, and it was considered that the growth of .betha.-Ti layer was controlled by interdiffusion rate process in .betha.-Ti. 4) The layer growth of TiCu, Ti$_{3}$Cu$_{4}$ and TiCu, phases formed near the Ti interface was linerface was linearly proportional to the brazing time, and it was considered that the layer growth of these phases was controlled by the chemical reaction rate at the interface.

• Journal of Technologic Dentistry
• /
• v.22 no.1
• /
• pp.69-78
• /
• 2000

The microstructure and corrosion behavior of commercially dental casting gold alloys were investigated to clarify the effect of burn-out temperature and cooling rate. In the case of water quenching after casting, only the αphase, which is typical dendritic microstructure of golda alloy, was detected. However, the precipitates along the grain boundary were detected only at the slow cooling rate and they increased inversely proportional to the burn-out temperature. This might be due to the time difference which solute atom could diffuse. EPMA and SEM results also demonstrated that the precipitate should be lamellar structure consisted of Ag rich phase(${\alpha}_1$) and Cu rich phase (${\alpha}_2$). In terms of corrosion, the galvanic coupling was formed due to the difference of composition between precipitates and matrix at the slow cooling rate. In the case of water quenching, the critical current density($i_p$) which indicate the degree of corrosion was lowest at $650^{\circ}C$ and below the burnout temperature, $i_p$ increased with it because of the effect of grain boundary segregation. But above the temperature, $i_p$ increased with it. This may be due to the strain field effect by residual thermal stress.

• Journal of the Korean Society for Heat Treatment
• /
• v.32 no.6
• /
• pp.256-262
• /
• 2019

The microstructural features and texture development by both hot rolling and hot forging in ${\gamma}-TiAl$ alloy were investigated. In addition, additional heat treatment after hot forging was conducted to recognize change of the microstructure and texture evolution. The obtained microstructural features through dynamic recrystallization after hot deformed ${\gamma}-TiAl$ were quite different because two kinds of formation process were occurred depending on deformation condition. However, analyzed texture tends to be random orientation due to intermediate annealing up to ${\alpha}+{\beta}$ region during the hot deformation process. After additional heat treatment, microstructure transformed into fully lamellar microstructure and randomly oriented texture was also observed due to the same reason as before. Tensile test at room temperature demonstrated that anisotropy of mechanical properties were not appeared and transgranular fracture was occurred between interface of ${\alpha}_2/{\gamma}$. As a result, it could be suggested that microstructural features influenced much more than texture development on mechanical properties at room temperature.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.26 no.1
• /
• pp.93-106
• /
• 2000

One phase liquid crystal formula was developed by using of nonionic surfactants, polyols, water and oils and its physical property was investigated. At the system oft to 1 ratio of POE octyldodecyl ether series, which have Y type (branch type) hydrophobic group, and POE glyceryl monostearate series, Y type hydrophilic group, it was examined that the formula at 7:3, 6:4, and 5:5 ratio of nonionic surfactant : polyols, shows L$\alpha$ , a pattern which is a typical characteristic of liquid crystal structure under the cross microscope polarized film. As results of L$\alpha$ phase diagram study, the formula which had high hydrophilic nonionic surfactant and the 7:3 ratio of nonionic surfactant : polyol appeared to increase the amount of oil containment and to be capable of the lamella formation. Besides it was examined that lamellar liquid crystal formula could contain about 25-40% water between lamella layers and it was transformed into w/o emulsion following as water content increased. When the lamella gel was applied into a human skin, it was investigated that it had effectiveness in increasing transepidermal water content of the skin.

• The Korean Journal of Physiology and Pharmacology
• /
• v.2 no.5
• /
• pp.617-628
• /
• 1998

In order to understand the pathogenetic mechanism of adult respiratory distress syndrome (ARDS), the role of phospholipase A2 (PLA2) in association with oxidative stress was investigated in rats. $Interleukin-1{\alpha}\;(IL-1,\;50\;{\mu}g/rat)$ was used to induce acute lung injury by neutrophilic respiratory burst. Five hours after IL-1 insufflation into trachea, microvascular integrity was disrupted, and protein leakage into the alveolar lumen was followed. An infiltration of neutrophils was clearly observed after IL-1 treatment. It was the origin of the generation of oxygen radicals causing oxidative stress in the lung. IL-1 increased tumor necrosis factor (TNF) and cytokine-induced neutrophil chemoattractant (CINC) in the bronchoalveolar lavage fluid, but mepacrine, a PLA2 inhibitor, did not change the levels of these cytokines. Although IL-1 increased PLA2 activity time-dependently, mepacrine inhibited the activity almost completely. Activation of PLA2 elevated leukotriene C4 and B4 (LTC4 and LTB4), and 6-keto-prostaglandin $F2{\alpha}\;(6-keto-PGF2{\alpha})$ was consumed completely by respiratory burst induced by IL-1. Mepacrine did not alter these changes in the contents of lipid mediators. To estimate the functional changes of alveolar barrier during the oxidative stress, quantitative changes of pulmonary surfactant, activity of gamma glutamyltransferase (GGT), and ultrastructural changes were examined. IL-1 increased the level of phospholipid in the bronchoalveolar lavage (BAL) fluid, which seemed to be caused by abnormal, pathological release of lamellar bodies into the alveolar lumen. Mepacrine recovered the amount of surfactant up to control level. IL-1 decreased GGT activity, while mepacrine restored it. In ultrastructural study, when treated with IL-1, marked necroses of endothelial cells and type II pneumocytes were observed, while mepacrine inhibited these pathological changes. In histochemical electron microscopy, increased generation of oxidants was identified around neutrophils and in the cytoplasm of type II pneumocytes. Mepacrine reduced the generation of oxidants in the tissue produced by neutrophilic respiratory burst. In immunoelectron microscopic study, PLA2 was identified in the cytoplasm of the type II pneumocytes after IL-1 treatment, but mepacrine diminished PLA2 particles in the cytoplasm of the type II pneumocyte. Based on these experimental results, it is suggested that PLA2 plays a pivotal role in inducing acute lung injury mediated by IL-1 through the oxidative stress by neutrophils. By causing endothelial damage, functional changes of pulmonary surfactant and alveolar type I pneumocyte, oxidative stress disrupts microvascular integrity and alveolar barrier.

• Applied Microscopy
• /
• v.29 no.4
• /
• pp.405-415
• /
• 1999

In general, transmission electron microscopy (TEM) is usually used in the investigation of polymer microstructure. Microtoming, solution casting, staining and carbon replica method are frequently introduced to the study of the polymer morphology with TEM, however the sample preparation procedure of those techniques is very difficult, and it takes a long time. The purpose of this study is to develop a new sample preparation technique which is suitable for the investigation of the various shapes and species of polyolefin microstructure by scanning electron microscopy (SEM). By modifying the conventional chemical etching method, we developed a new chemical etching technique and sample preparation procedure that are suitable for SEM study of polymer microstructure. In this study the permanganate etching method is introduced and the optimum etching condition are determined by simply adjusting the etchant formulation, concentration and etching time. This technique has shown good reproducibility and it's morphological results agree well with other works on various types of microstructures such as spherulite characterization of isotatic polypropylene $(\alpha/\beta)$, polyethylene and poly-propylene copolymer characterization, and the study of lamellar growth pattern of unsheared or oriented materials. This technique has also been applied to the industrial fields for characterization of the polyolefin film, automobile products and the others.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.231-237
• /
• 2005

The sizes and structure of micelles and vesicles formed in ammonium dodecyl sulfate (ADS)/octadecyl trimethyl ammonium chloride (OTAC) mixed aqueous solutions were analyzed by small-angle neutron scattering. In micellar regions of pure ADS and OTAC aqueous solution, the spherical micelles were formed at given concentrations and their sizes were 40 and $61{\AA}$, respectively. The structure transition of pure micelles occurred above 300 mM due to the constancy of the intermicellar distance above 250 mM. The coexisting region of mixed micelles and vesicles in phase diagram of mixed system was also assured. It was investigated that vesicle formed spontaneously took a bilayer structure. The lamellar thickness of vesicles decreased with increasing concentration of vesicle samples. However, the size could not be determined for mixed micelle and vesicle above 100 nm due to limitation of low q ranges. Finally, The 9 mM solution of ADS mole fraction 0.9 (${\alpha}$=0.9) showed bilayer structure compared to phase diagram classified into mixed micelle.

• Journal of Powder Materials
• /
• v.21 no.4
• /
• pp.277-285
• /
• 2014

The effects of processing parameters on the flow behavior and microstructures were investigated in hot compression of powder metallurgy (P/M) Ti-6Al-4V alloy. The alloy was fabricated by a blended elemental (B/E) approach and it exhibited lamellar ${\alpha}+{\beta}$ microstructure. The hot compression tests were performed in the range of temperature $800-1000^{\circ}C$ with $50^{\circ}C$ intervals, strain rate $10^{-4}-10s^{-1}$, and strain up to 0.5. At $800-950^{\circ}C$, continuous flow softening after a peak stress was observed with strain rates lower than $0.1s^{-1}$. At strain rates higher than $1s^{-1}$, rapid drop in flow stress with strain hardening or broad oscillations was recorded. The processing map of P/M Ti-6Al-4V was designed based on the compression test and revealed the peak efficiency at $850^{\circ}C$ and $0.001s^{-1}$. As the processing temperature increased, the volume fraction of ${\beta}$ phase was increased. In addition, below $950^{\circ}C$, the globularization of phase at the slower strain rate and kinking microstructures were found. Based on these data, the preferred working condition of the alloy may be in the range of $850-950^{\circ}C$ and strain rate of $0.001-0.01s^{-1}$.