• Tunnel and Underground Space
• /
• v.11 no.1
• /
• pp.59-63
• /
• 2001

The total number of elastic constants of an anisotropic body is 9 and thus it is very difficult to measure these constants experimentally. The number of elastic constants can be reduced if a rock or rock mass is regarded as isotropic or transversely isotropic material. Since only 4 stress-strain relationships can be obtained, it is theoretically impossible to determine all 5 constants from a single uniaxial compression teat. Lekhnitskii overcame this problem by suggesting the fifth equation based on laboratory tests. But his equation is theoretically wrong and does not agree with experimental results. This paper describes the stress-strain relationships and the independent/dependent elastic constants of an anisotropic mass and suggests a testing mothed to determine 5 independent elastic constants for a transversely isotropic rock.

• Geomechanics and Engineering
• /
• v.21 no.1
• /
• pp.11-21
• /
• 2020

The traditional formulations for estimation of bearing capacity in rock mechanics assume a homogeneous and isotropic rock mass. However, it is common that the rock mass consists of different layers of different rock properties or of the same rock matrix with distinct geotechnical quality levels. The bearing capacity of a heterogeneous rock is estimated traditionally through the weighted average. In this paper, the solution of the weighted average is compared to the finite difference method applied to a bilayer rock mass. The influence of different parameters such as the thickness of the layers, the rock type, the uniaxial compressive strength and the overall geotechnical quality of the rock mass on the bearing capacity of a bilayer rock mass is analyzed. A parametric study by finite difference method is carried out to develop a bearing capacity factor in function of the layer thickness and the rock mass quality expressed in terms of the geological strength index, which is presented in a form of a chart. Therefore, this correlation factor allows estimating the bearing capacity of a rock mass that is formed by two layers with distinct GSI, depending on the bearing capacity of the rock mass formed only by the upper layer and considered by that way as homogenous and isotropic rock mass.

• Tunnel and Underground Space
• /
• v.15 no.4 s.57
• /
• pp.288-295
• /
• 2005

Many mechanical defects originated from various geological causes make rock mass exhibit anisotropic characteristics. Understanding how the stress distribution occurs in anisotropic rock mass is, therefore, very important for the design of footings on rock and rock structures. In this study, the patterns of elastic stress distribution, developed by acting line load on the surface, in transversely isotropic was investigated. The influence of joint stiffness, joint spacing, and dip angle on the stress distribution was examined. By assuming the Mohr-Coulomb criterion as joint slip condition, the development of joint slip zone was also discussed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.58-63
• /
• 2009

Biaxial compression test was conducted on a transversely isotropic synthetic jointed rock model for the understanding of the fracture behaviors of a sedimentary or metamorphic rocks with well developed bedding or foliation in uni-direction. The joint angles employed for the model are 30, 45, and 60 degrees to the horizontal, and the synthetic rock mass was made of early strength cement. From the biaxial compression test, initiation propagation of tensile cracks at norm to the joint angle was found. The propagated tensile cracks eventually developed rock blocks, which was dislodged from the rock mass. Furthermore, the propagation process of the tensile cracks varies with joint angle: lower joint angle model shows more stable and progressive tensile crack propagation. The experiment results were validated from the simulation by using discrete element method PFC 2D. From the simulation, as has been observed from the test, a rock mass with lower joint angle produces wider damage region and rock block by tensile cracks. In addition, a rock model with lower joint angle shows a progressive tensile cracks generation around the opening from the investigation of the interacted tensile cracks.

• Tunnel and Underground Space
• /
• v.14 no.5
• /
• pp.339-344
• /
• 2004

Variation of horizontal to vertical stress ratio of transversely isotropic rock caused by erosion was studied by numerical analysis. Influence of transversely isotropic was less than 5% for isotropic case. Difference between stresses obtained by numerical analysis and theoretical solution was small when initial stress ratio was small and the difference increased as erosion depth increased. Stress ratios diverged from initial ones as depth increased. An equation to determine stress ratio considering erosion according to the analyses was suggested.

• Tunnel and Underground Space
• /
• v.15 no.6 s.59
• /
• pp.391-399
• /
• 2005

In this study, stress difference between isotropic and transversely isotropic rock mass, and planar principal stresses at the periphery of the tunnel in the rock with various ratio of anisotropy were determined theoretically. Stress differences between isotropic and anisotropic calculations at crown. side walls and floor of a tunnel with assumed stress states were analyzed and compare each other by $FLAC^{2D}$, a finite differential element method. As a result, magnitude and direction of principal stresses in the case of ignoring anisotropy were different from those of anisotropic cases, whatever the stress state was. Stress difference increased as the ratio of anisotropy increased. Direction or anisotropy affected stress difference, especially in the cases of anisotropic directions of $45^{\circ}\;and\;135^{\circ}$ of counterclockwise from x direction.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1484-1489
• /
• 2005

An inhomogeneous and anisotropic rock has different properties at different location. Thus, this refers to any of the properties which we may be measuring. There are two concepts of rock mass, namely, CHILE(Continuous, Homogeneous, Isotropic, Linear Elastic) material and DIANE(Discontinuous, Inhomogeneous, Anisotropic, Non-linear Elastic) rock. The former is essentially the properties of intact rock, the latter is essentially the properties governed by the structure of rock. In geotechnical aspect, the most important parameter is strength of rock or rock mass. In particular, characteristics of strength of rock mass depend upon the orientation of discontinuities And this orientation of discontinuities has different properties at different direction of excavation. Therefore, it needs for characterization of different properties of discontinuity orientation against different direction of excavation.

• Geomechanics and Engineering
• /
• v.24 no.3
• /
• pp.227-235
• /
• 2021

A criterion and a method for solving a problem on the prevention of mine working fracture under the action of tectonic and gravitational forces are offered. Based on minimal criterion, theoretical analysis of the definition of the optimal shape of working in the rock mass weakened by arbitrarily located rectilinear cracks was carried out. A closed system of algebraic equations allowing to minimize the stress state and stress intensity factors depending on mechanical and geometrical characteristics of the rock, is constructed. The relation between the shape of the working and the stress intensity factors and also location and sizes of the cracks is obtained. The found optimal shape of working increases load-bearing capacity of the rock.

• Tunnel and Underground Space
• /
• v.10 no.2
• /
• pp.165-172
• /
• 2000

When tunnels or underground structures are constructed in anisotropic rock mass, designers and constructors have to consider the anisotropic characteristics in rock mass because their physical and mechanical properties are depended on the anisotropic angles(${\beta}$). In this study, therefore, we have first investigated the mechanical behavior of the gneiss specimen from lab. tests, and then have analysed the behavior of specimens for to the transversely isotropic model in elastic medium using the FLAC program. The results of this study were summarized as follows; 1) In the result of the variation tests, in general, the properties of strength were depended on the angle of inclination in spite of the hard rock. And except for the shear strength test, the lowest and peak stress were appeared at 60$^{\circ}$ and 90$^{\circ}$respectively. 2) The results of specimen modeling analysis using FDM well indicated the mechanical behaviors of the specimen of transversely isotropic model.

• Geomechanics and Engineering
• /
• v.6 no.3
• /
• pp.213-233
• /
• 2014

The present paper is dealing with the investigation of the stress field around the infinitely long cylindrical cavity, of a circular cross section, contained in the transversally isotropic elastic continuum. Investigation is based upon the determination of the stress function that satisfies the biharmonic equation, for the given boundary conditions and for rotationaly symmetric loading. The solution of the partial differential equation of the problem is given in the form of infinite series of Bessel's functions. Determination of the stress-strain field around cavities is a common requirement for estimation of safety of underground rock excavations.