• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.723-726
• /
• 2005

The two major obstacles in the application of IPMC to flapping actuators operated in the air are solvent loss and actuation force. In this paper, solvent loss of various IPMCs made of Nafion$^{TM}$117(183$\mu$m thickness) has been experimentally investigated to find out the best combination of cation and solvent for minimal solvent loss in IPMCs and higher actuation force. For this purpose. experiments for the internal solvent loss measurement of IMPCs have been conducted for various combinations of cation and solvent. From the experiments, it was found that heavy water showed improvement in the operating time up to more than two minutes. in the tip force measurement of IPMCs, it was found that smaller and thicker IPMCs produced larger tip forces. However, the shorter IPMCs generated reduced actuation displacements and created flapping motion with decreased natural frequency. For the design of flapping device actuated by 5mm wide, 10mm long, 0.2mm thick IPMCs were used in the stacked form. Since the actuation force is a few gram-force, we stacked five IPMCs to improve actuation force. To amply the actuation force, rack-and-pin ion type hinge was used for the flapping device and insect (Cicadidae) wing was attached to the stacked IPMC actuator. In the flapping test, the device could generate flapping angle of 15$^{\circ}$ at 6Hz excitation by 2.5 voltage square wave input.

• Journal of Radiation Protection and Research
• /
• v.28 no.3
• /
• pp.255-261
• /
• 2003

An environmental radiation monitoring system based on high pressurized ionization chamber has been used for on-line gamma monitoring surrounding the KAERI (Korea Atomic Energy Research Institute), which transmits the dose data measured from ion chamber on the site via radio frequency to a central processing computer and stores the transmitted real-time data. Although communication using radio frequency has several advantages such as effective and economical transmission, storage, and data process, there is one main disadvantage that data loss during transmission often happens because of unexpected communication problems. It is possible to restore the loss data by off-line such as floppy disk but the simultaneous process and display of current data as well as the backup data are very difficult in the present on-line system. In this work, a new electronic circuit board and the operation software applicable to the conventional environmental radiation monitoring system are developed and the automatical synchronization of the ion chamber unit and the central processing computer is carried out every day. This system is automatically able to restore the backup data within 34 hours without additional equipments and also display together the current data as well as the transmitted backup data after checking time flag.

• Journal of the Korean Ceramic Society
• /
• v.53 no.3
• /
• pp.349-353
• /
• 2016

We prepared a number of reaction-bonded silicon carbides (RBSCs) made from various mixing ratios of raw SiC particles, and investigated their microstructure and etch characteristics by Reactive Ion Etch (RIE). Increasing the amount of $9.5{\mu}m$-SiC particles results in a microstructure with relatively coarser Si regions. On the other hand, increasing that of $2.6{\mu}m$-SiC particles produces much finer Si regions. The addition of more than 50 wt% of $2.6{\mu}m$-SiC particles, however, causes the microstructure to become partially coarse. We also evaluated their etching behaviors in terms of surface roughness (Ra), density and weight changes, and microstructure development by employing Confocal Laser Scanning Microscope (CLSM) and Scanning Electron Microscope (SEM) techniques. During the etching process of the prepared samples, we confirmed that the residual Si region was rapidly removed and formed pits isolating SiC particles as islands. This leads to more intensified ion field on the SiC islands, and causes physical corrosion on them. Increased addition of $2.6{\mu}m$-SiC particles produces finer residual Si region, and thus decreases the surface roughness (Ra.) as well as causing weight loss after etching process by following the above etching mechanism.

• Journal of the Korean Chemical Society
• /
• v.39 no.8
• /
• pp.611-616
• /
• 1995

Oxovanadium(IV) complexes with salicylaldoxime, o-vanilline oxime, 2-hydroxy-4-methoxybenzaldoxime, 2-hydroxy-5-methoxybenzaldoxime and 2-hydroxy-5-nitrobenzaldoxime were synthesized. The complexes have been characterized by elemental analysis, electric conductivity measurement, infrared spectrometry, electronic spectrometry, mass spectrometry, and thermal analysis. The results of elemental analysis were well coincided with the theoretical values. The values of molar conductance of the complexes in DMF implicated that the complexes were non-electrolyte. The characteristic stretching frequency of V=O appeared strong band in the range of $980{\pm}20\;cm^{-1}.$ All the complexes showed two d-d transition in visible spectra and two charge transfer transitions in ultraviolet spectra. Results of mass spectrometry of $VO(sal)_2\;and\;VO(van)_2$ indicated two peaks corresponding to vanadium containing ion(I) of 1 : 2(metal to ligand) chelate and a fragment ion(II) of 1 : 1 chelate due to loss of ligand radical from ion(I). The thermal analysis showed the endothermic peak due to the thermal decomposition.

• Clean Technology
• /
• v.19 no.1
• /
• pp.44-50
• /
• 2013

Tin-based materials for lithium ion battery have been proposed as new anode candidates owing to their higher specific capacity and relatively high lithium insertion potential. Tin-based materials have been extensively studied as possible replacements for carbon anodes in lithium ion batteries. However, the large volume expansion results in severe particle cracking with loss of electrical contact, giving irreversible capacity losses which prevent the widespread use of tin-based materials in lithium batteries. So remaining studies of tin-based materials are alleviating volume expansion and improving cycle performance. In this work, $SnO_2-SiO_2$ composites were manufactured with sol-gel method to overcome their volume expansion. Carbon was coated with 10 vol% propylene gas. The characteristics of active material and the effect of heat treatment were investigated with TG/DTA, XRD, SEM and FT-IR. Electrochemical characteristics of these composites were measured with CR2032 type coin cells. Carbon coated $SnO_2-SiO_2$at $300^{\circ}C$ heat treatment showed the best electrochemical performance.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.136-136
• /
• 2003

In fiber optic networks, system size and cost can be significantly reduced by development of optical components through planar optical waveguides. One important step to realize the compact optical devices is to develop planar optical amplifier to compensate the losses in splitter or other components. Planar amplifier provides optical gain in devices less than tens of centimeters long, as opposed to fiber amplifiers with lengths of typically tens of meters. To achieve the same amount of gain between the planar and fiber optical amplifier, much higher Er doping levels responsible for the gain than in the fiber amplifier are required due to the reduced path length. These doping must be done without the loss of homogeniety to minimize Er ion-ion interactions which reduce gain by co-operative upconversion. Sol-gel process has become a feasible method to allow the incorporation of Er ion concentrations higher than conventional glass melting methods. In this work, Er-doped $SiO_2$-A1$_2$ $O_3$ films were prepared by two different method via sol -Eel process. Tetraethylorthosilicate(TEOS)/aluminum secondary butoxide [Al (OC$_4$ $H_{9}$)$_3$], methacryloxypropylcnethoxysaane(MPTS)/aluminum secondary butofde [Al(OC$_4$ $H_{9}$)$_3$] systems were used as starting materials for hosting Er ions. Er-doped $SiO_2$-A1$_2$ $O_3$ films obtahed after heat-treating, coatings on Si substrate were characterized by X-ray din action, FT-IR, and N-IR fluorescence spectroscopy. The luminescence properties for two different processing procedure will be compared and discussed from peak intensity and life time.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.11a
• /
• pp.40-43
• /
• 2006

Public demand for the heat pump system as a next generation energy equipment is increasing for its eco-friendly and cost-effective advantage. Many researches have been concentrated on how to calculate and develop its own efficiency, while the possible effect of the heat pump operation on the whole subsurface temperature distribution is relatively less considered, During the current study, subsurface temperature disturbance caused by seasonal surface temperature cycle in Busan area and general W-tube heat pump operation is simulated in 3-dimensional heterogeneous medium. It shows that subsurface deeper than 10m from the surface remains nearly unchanged throughout the 4 seasons and groundwater convect ion in highly permeable layer near the surface acts like a main path of heat plume from heat pump system, This implies the significance of detail descript ion in shallow sedimentary layer or highly permeable layer which plays an important role on the regional flow advection and heat transfer. Also, the effect of groundwater convection increases when the arrangement of the 2 injection pipes and 2 extract ion well is maintained parallel to groundwater flow. Therefore, more careful and detail investigation is required before installation and operation of heat pump system that it may not cause any possible change of microbial ecosystem in the shallow subsurface environment or 'contamination of temperature' for groundwater use as well as the loss of efficiency of the equipment itself. This can also help to design the optimized grouting system for heat pump.

• Korean Journal of Pharmacognosy
• /
• v.30 no.3
• /
• pp.306-313
• /
• 1999

Polyphenol Oxidase(PPO) was purified from an extract of Ginkgo biloba leaves by ammonium sulfate fractionation followed by sephadex G-150 column chromatography, which resulted in a 18-fold increase in specific activity. The enzyme was most active at pH 8.5 and the temperature optimum for the PPO catechol oxidation reaction was $45^{\circ}C$. Heat inactivation studies showed that heating for 7, 9 and 48 min, at 80, 70 and $60^{\circ}C$ respectively caused a 50% loss in enzymatic activity and that the enzyme was completely inactivated after heat treatment at $90^{\circ}C$ for 60 min. Km values of the PPO for catechol, hydroquinone and 4-methylcatechol derived from Lineweaver-Burk plots were $6.06\;{\times}\;10^{-4}M,\;1.02\;{\times}\;10^{-3}M,\;1.41\;{\times}\;10^{-3}M$ respectively. Of the substrates tested, 4-methylcatechol was oxidized most readily and the enzyme did not oxidize monophenols. The enzyme datalyzed browning reaction was completely inhibited in the presence of reducing reagents, namely ascorbic acid, cysteine, glutathione, 2-mercaptoethanol, potassium metabisulfite at 0.5 mM level. Sodium chloride showed very little inhibition effect on Ginkgo biloba leaves PPO. Lineweaver-Burk analysis of inhibition data revealed that the inhibition by cysteine, 2-mercaptoethanol, potassium cyanide was competitive with ki values of $1.1\;{\times}\;10^{-5}M,\;2.4\;{\times}\;10^{-5}M,\;8\;{\times}\;10^{-5}M$, respectively. Among the divalent cations, $Cu^{2+}ion$ was a strong activator on PPO and $Mn^{2+}ion$ was little or no effect on PPO activity $Ni^{2+}ion$ was an inhibitor on PPO.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.2
• /
• pp.357-364
• /
• 2014

Size controlled, $LiNi_{0.8}Co_{0.15}Al_{0.05}O_2$ cathode powders were prepared by co-precipitation method followed by heat treatment at temperatures between 750 and $850^{\circ}C$. The synthesized samples are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical performance. The synthesized $LiNi_{0.8}Co_{0.15}Al_{0.05}O_2$ after calcined at $750^{\circ}C$ has a good electrochemical performance with an initial discharge capacity of $190mAhg^{-1}$ and good capacity retention of 100% after 30 cycles at 0.1C ($17mAg^{-1}$). The capacity retention of $LiNi_{0.8}Co_{0.15}Al_{0.05}O_2$ after calcined at $750^{\circ}C$ is better than that at 800 and $850^{\circ}C$ without capacity loss at various high C rates. This is ascribed to the minimized cation disorder, a higher conductivity, and higher lithium ion diffusion coefficient ($D_{Li}$) observed in this material. In the differential scanning calorimetry DSC profile of the charged sample, the generation of heat by exothermic reaction was decreased by calcined at high temperature, and this decrease is especially at $850^{\circ}C$. This behavior implies that the high temperature calcinations of $LiNi_{0.8}Co_{0.15}Al_{0.05}O_2$ prevent phase transitions with the release of oxygen.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.2
• /
• pp.140-145
• /
• 2008

The purpose of this paper is to discuss the fabrication of $\beta$-PVDF($\beta$-Polyvinylidene fluoride, ${\beta}-PVF_2$) organic thin films using the vapor deposition method. Vapor deposition was performed under the following conditions: the temperature of evaporator, the applied electric field, and the pressure of reaction chamber were $270^{\circ}C$, 142.4 kV/cm, and $2.0{\times}10^{-5}\;Torr$, respectively. The molecular structure of the evaporated organic thin films were evaluated by a FT-IR. The results showed that the characteristic absorption peaks of $\beta$-form crystal increase from 72% to 95.5% with an increase in the substrate temperature. In the analysis of the electric characteristics, the abnormal increases in the relative dielectric constant and the dielectric loss factor in the regions of low frequency and high temperature are known to be caused by inclusion of impurity carriers in the PVDF organic thin films. In order to analyze quantitatively the abnormalities in the conductivity mechanism caused by ionic impurities, the product of the ion density and the mobility that affect the electrical property in polymeric insulators is analyzed. In the case of a specimen produced by varying the substrate temperature from $30^{\circ}C$ to $105^{\circ}C$, the product of mobility and the ion density decreased from $4.626{\times}10^8$ to $8.47{\times}10^7/V{\cdot}cm{\cdot}s$. This result suggests that the higher the substrate temperature is maintained, the better excluded the impurities are, and the more electrically stable material can be obtained.