• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.2
• /
• pp.99-104
• /
• 2021

Ion-beam sputtering (IBS) was used to deposit semiconducting IZTO (indium zinc tin oxide) thin films onto heavily-doped Si substrates using a sintered ceramic target with the nominal composition In0.4Zn0.5Sn0.1O1.5, which could work as a channel layer for oxide TFT (oxide thin film transistor) devices. The crystallization behavior and electrical properties were examined for the films in terms of deposition parameters, i.e. target tilt angle and substrate temperature during deposition. The thickness uniformity of the films were examined using a stylus profilometer. The observed difference in electrical properties was not related to the degree of crystallization but to the deposition temperature which affected charge carrier concentration (n), electrical resistivity (ρ), sheet resistance (Rs), and Hall mobility (μH) values of the films.

• Clean Technology
• /
• v.16 no.2
• /
• pp.140-144
• /
• 2010

Titania-silica composite materials were obtained by sol-gel method from TiCl4 and TEOS precusors, and they were applied to anode materials of lithium ion battery. Uniformly distributed composite materials can be manufactured by sol-gel method. The composite materials were heat treated by microwave to obtain materials with new properties. The experimental variables were composition of the material, heat treatment temperature, and microwave exposure. The structure and surface properties of the materials were analyzed by XRD, SEM, and the electrochemical capacity was measured with charge/discharge cycler.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.640-647
• /
• 2023

Material corrosion in nuclear power plant (NPP) is not controlled only by amine injection but also by ion exchange (IX) which is the best option to remove trace Na⁺. This study was conducted to understand the Na⁺ leakage characteristics of IX beds packed with ethanolamine-form (ETAH-form) and hydrogen-form (H-form) resins in the simulated water-steam cycle in terms of intrinsic behaviors of four kinds of cation-exchange resins through ASTM test and Vanselow mass action modeling. Na⁺ was inappreciably escaped throughout the channel created in resin layer. Na⁺ leakage from IX bed was non-linearly raised because of its decreasing selectivity with increasing Na⁺ capture and with increasing the fraction of ETAH-form resin. Na⁺ did not reach the breakthrough earlier than ETAH⁺ and NH₄⁺ due to the increased selectivity of Na⁺ to the cation-exchange resin (H⁺ < ETAH⁺ < NH₄⁺ ≪ Na⁺) at the feed composition. Na⁺ leakage from the resin bed filled with small particles was decreased due to the enhanced dynamic IX processes, regardless of its low selectivity. Thus, the particle size is a predominant factor among intrinsic properties of IX resin to reduce Na⁺ leakage from the condensate polishing plant (CPP) in NPPs.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.5
• /
• pp.335-340
• /
• 2023

Quinary component of 3㎛ thick Ti-Al-Si-Cu-N films were deposited onto WC-Co and Si wafer substrates by using an arc ion plating(AIP) system. In this study, the influence of copper(Cu) contents on the mechanical properties and microstructure of the films were investigated. The hardness of the films with 3.1 at.% Cu addition exhibited the hardness value of above 42 GPa due to the microstructural change as well as the solid-solution hardening. The instrumental analyses revealed that the deposited film with Cu content of 3.1 at.% was a nano-composites with nano-sized crystallites (5-7 nm in dia.) and a thin layer of amorphous Si₃N₄ phase.

• Corrosion Science and Technology
• /
• v.23 no.3
• /
• pp.179-194
• /
• 2024

A layer-by-layer coating was produced using electrophoretic deposition for a HA/Al₂O₃ coating layer and a bioglass coating layer on Co-Cr-Mo alloy with a roughness of 0.5 ㎛ (400 emery paper SiC). The corrosion behaviour was analyzed by assessing the coating layers' exceptional corrosion resistance, which outperformed the substrate. Cr ion release test using AAS was carried out, indicating that factional graded coating inhibited ion release from the uncoated substrate to coated sample. The porosity was expressed as a percentage, representing the extent of imperfections on the surface of all coatings. These imperfections fell within an acceptable range of 1% to 3%. The roughness of the coated surface was measured using atomic force microscopy, which revealed an excellent roughness value of 3.32 nm. Tape test technique for adhesion revealed that the removal area of the substrate coating layer varied by 11.92%. X-ray diffraction analysis confirmed the presence of all coating material peaks and verified phases of the deposited coating layers. These findings provided evidence that the coating composition remains unaffected by the electrophoretic deposition process. The bioactivity was assessed by immersion in a simulated bodily fluid, which revealed the formation of HCA during a period of 5 days.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.6
• /
• pp.580-586
• /
• 2016

Cr-Si-Al-N coating with different Si content were deposited by hybrid physical vapor deposition (PVD) method consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP). The deposition temperature was $300^{\circ}C$, and the gas ratio of $Ar/N_2$ were 9:1. The CrSi alloy and aluminum targets used for arc ion plating and sputtering process, respectively. Si content of the CrSi alloy targets were varied with 1 at%, 5 at%, and 10 at%. The phase analysis, composition and microstructural analysis performed using x-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) including energy dispersive spectroscopy (EDS), respectively. All of the coatings grown with textured CrN phase (200) plane. The thickness of the Cr-Si-Al-N films were measured about $2{\mu}m$. The friction coefficient and removal rate of films were measured by a ball-on-disk test under 20N load. The friction coefficient of all samples were 0.6 ~ 0.8. Among all of the samples, the removal rate of CrSiAlN (10 at% Si) film shows the lowest values, $4.827{\times}10^{-12}mm^3/Nm$. As increasing of Si contents of the CrSiAlN coatings, the hardness and elastic modulus of CrSiAlN coatings were increased. The morphology and composition of wear track of the films was examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy, respectively. The surface energy of the films were obtained by measuring of contact angle of water drop. Among all of the samples, the CrSiAlN (10 at% Si) films shows the highest value of the surface energy, 41 N/m.

• Korean Journal of Soil Science and Fertilizer
• /
• v.40 no.2
• /
• pp.151-155
• /
• 2007

The issue of acid precipitation and related environmental problems in East Asia have been emerging. To evaluate the acidity and chemical characteristics of rainwater in Korea, its chemical properties during crop cultivation season from April to October were investigated at Suwon, Korea. Also, to estimate the contribution of ions on its acidity, ion composition characteristics and neutralization effects by cation ions were determined. Ion balance and electrical conductivity balance between the measured and estimated values showed high correlation. Rainwater had distributed highly in the range of pH 4.5~5.6. The pH of rainwater was relatively high at June as compared with other monitoring periods. $Na^+$ was the main cation followed by $NH_4{^+}$, $Ca^{2+}$, $H^+$ > $K^+$ > $Mg^{2+}$. Among these, $Na^+$, $NH_4{^+}$, $Ca^{2+}$ and $H^+$ covered over 93% of total cations. About 86% of anion in rainwater was composed of $SO{_4}^{2-}$ and $NO_3{^-}$. In rainwater samples, $NH_4{^+}$ and $Ca^{2+}$ contributed greatly to neutralization of the rain acidity. Also, 88% of soluble sulfate in rainwater was nss-$SO{_4}^{2-}$(non-sea salt sulfate).

• Clean Technology
• /
• v.26 no.4
• /
• pp.263-269
• /
• 2020

Zeolite was synthesized hydrothermally using the water-treatment sludge, and the effects of various synthesis parameters like reaction temperature, reaction time, and Na2O/SiO2 molar ratio on the crystallization of zeolite were investigated. Crystal structure, physical property, and thermal stability of zeolite crystals were characterized by X-ray powder diffraction, FTIR spectroscopy, BET nitrogen adsorption, and TGA measurements. The removal efficiencies of nitrogen in ammonia, heavy metal ions, and TOC were calculated to evaluate zeolite's adsorption capacity. The primary chemical composition of water-treatment sludge was 28.79% Al2O3 and 27.06% SiO2. The zeolites were synthesized by merely employing the water-treatment sludge as silica and alumina sources without additional chemicals. Zeolite crystals synthesized through the water-treatment sludge were confirmed as an A-type zeolite structure. Zeolite A had the highest crystallinity obtained from a gel with the molar composition 2.1Na2O-Al2O3-1.6SiO2-65H2O after 5 h at a temperature of 90 ℃. The specific surface area of zeolite obtained was 55 ㎡ g-1, which was higher than commercial zeolite A. The removal efficiency of nitrogen in ammonia was 68% after 3 h of reaction time, while the removal efficiencies of Pb2+ and Cd2+ ions were 99.1% and 99.3%, respectively. These results indicate active ion exchange between Pb2+ or Cd2+ ion and Na+ ion in the zeolite framework. The adsorption experiments on the different zeolite addition conditions were performed for 3 h with 300 ppm humic acid. Based on the results, TOC's highest efficiency was 83% when 5 g of zeolite was added.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.46 no.3
• /
• pp.15-22
• /
• 2023

BNKT Ceramics, one of the representative Pb free based piezoelectric ceramics, constitutes a perovskite(ABO3) structure. At this time, the perovskite structure (ABO3) is in the form where the corners of the octahedrons are connected, and in the unit cell, two ions, A and B, are cations, A ion is located at the body center, B ion is located at each corner, and an anion O is located at the center of each side. Since Bi, Na, and K sources constituting the A site are highly volatile at a sintering temperature of 1100℃ or higher, it is difficult to maintain uniformity of the composition. In order to solve this problem, there should be suppression of volatilization of the A site material or additional compensation of the volatilized. In this study, the basic composition of BNKT Ceramics was set to Bi_0.5(Na_0.78K_0.22)_0.5TiO₃ (= BNKT), and volatile site (Bi, Na, and K sources) were coated in the form of a shell to compensate additionally for the A site ions. In addition, the physical and electrical properties of BNKT and its coated with shell additives(= @BNK) were compared and analyzed, respectively. As a result of analyzing the crystal structure through XRD, both BNKT(Core) and @BNK(Shell) had perovskite phases, and the crystallinity was almost similar. Although the Curie temperature of the two sintered bodies was almost the same (TC = 290 ~ 300 ℃), it was confirmed that the d33 (piezoelectric coefficient) and Pr (residual polarization) values were different. The experimental results indicated that the additional compensation for a shell additive causes the coarsening, resulting in a decrease in sintering density and Pr(remanent polarization). However, coating shell additives to compensate for A site ion is an effective way to suppress volatilization. Based on these experimental results, it would be the biggest advantage to develop an eco-friendly material (Lead-free) that replaced lead (Pb), which is harmful to the human body. This lead-free piezoelectric material can be applied to a biomedical device or products(ex. earphones (hearing aids), heart rate monitors, ultrasonic vibrators, etc.) and skin beauty improvement products (mask packs for whitening and wrinkle improvement).

• Analytical Science and Technology
• /
• v.10 no.4
• /
• pp.231-239
• /
• 1997

We developed a procedure that can effectively separate and determine tertiary amines and quaternary ammonium salts in some samples with reverse phase ion-pair high performance chromatography, employing indirect spectrophotometric detection method. Detection and ion-pairing reagents used in this study were benzyl trimethylammonium chloride (BTMACl) and sodium dodecyl sulfate(DDSANa), respectively. Eluting the electrolyte solutions of some commercial electrolytic capacitors with a MeOH(40):water(60) eluent (pH 8.5 adjusted with NH4Cl-NH3 buffer) containing 0.010M DDSANa and 0.004 M BTMACl through Supelco LC-18 or ${\mu}$-Bondapak phenyl column, amines and ammonium salts contained in the sample were successfully separated and determined. Varying the composition, especially the content of quaternary ammonium salts, of electrolyte solutions based on this analysis. we could prepare the low impedance(0.08~0.13) electrolytic capacitors with excellent electrical properties and it was a confirmation that the analysis is favorable.