• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.43-50
• /
• 2002

In the design of structure, the forces acting on tai structure are key parameter fur noise and vibration control. However, in the complex structure, the forces at the injection point on the structure cannot be measured directly. So, it is necessary to find out Indirect force evaluation method. In this paper, forces have been measured with In-situ vibration responses and system information. And, three existing techniques of indirect force measurement, vita. direct inverse. principal component analysis and regularization have been compared. This paper shows that multi-vibration responses are essential for talc precise estimation of the forces. To check these conditions, rotary compressor is adopted as test sample, because it is very difficult to measure the injection forces from internal excitation to shell. It alas also been obtained that relatively higher force is transmitted through three welding paths to the compressor shell. It shows a good agreement between direct and indirect force evaluation with curvature shell and plate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.564-567
• /
• 1997

In the design of structure the forces acting on the structure are important parameter for noise and vibration control. However, in the complex structure, the forces at the injection point on the structure cannot be measured directly. Thus it is necessary to find out indirect force evaluation method. In this paper forces have been measured with in-situ vibration responses and system information. Three existing techniques of indirect force measurement, viz. direct inverse, principal component analysis and regularization have been compared. It has been shown that multi-vibration responses are essential for the precise estimation of the forces. To satisfy those conditions, Rotary compressor is adopted as test sample, because it is very difficult to measure the injection forces from internal excitation to shell. It has also been obtained that relatively higher force is transmitted though three welding paths to the compressor shell. It shows a good agreement between direct and indirect force evaluation with curvature shell and plate and is investigated the possibility of force evaluation of rotary compressor as a complex structure.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2003.11a
• /
• pp.684-689
• /
• 2003

One field identified by an inverse method is one of multiple candidate solutions those are independently obtained through a specific estimation technique. While averaging of optimized fields can provide a better description of the spatial feature of an unknown field, it deteriorates the flow and transport characteristics of the optimized fields. As a result, the averaged field is not suited for modeling aquifer performances. Based on genetic algorithm, an optimal field synthesis technique is developed, which combines diversely optimized fields into a refined group of fields. Each field in the population is paired, and a sub-region of each field is exchanged by crossover operation to create a group of synthesized fields of enhanced modeling capability. The population of the fields is evolved till the synthesized fields become sufficiently similar. Applications of the optimal field synthesis to synthetic cases indicate that the objective functions of the fields assessing the modeling capabilities are further reduced after the optimal field synthesis. The identified fields from various inverse techniques may yield a range of modeling results under varied flow situations. The uncertainty is narrowed down through the optimal field synthesis and the associated modeling results converge on that of the reference field. The developed inverse modeling facilitates the construction of a reliable simulation model and hence trustworthy predictions of the future performances.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.106-113
• /
• 2004

Most of mechanical structures are composed of many substructures connected to one another by various types of mechanical joints. In automotive engineering, it is important to study these connected structures under various dynamic forces for the evaluations of fatigue life and stress concentration exactly. In this study, the dynamic response of vehicle structure to external forces is classified an inverse problem involving strains from the experiment and the analysis. The practical dynamic forces are determined by the combination of the analytical and experimental method with analyzed strain by quasi-static finite element analysis under unit force and with measured strain by a strain gage under driving load, respectively. In a stressed body, inter-molecular chemical bonds are failed beyond the certain magnitude. The failure of molecular structure in material is considered as a time process of which rate is determined by mechanical stress. That is, the failure of inter-molecular chemical bonds is the fatigue lift of material. This kinetic concept is expressed as lethargy coefficient. And S-N curve is obtained with the lethargy coefficient from quasi-static tensile test. Equivalent practical dynamic force is obtained from the identification of practical dynamic force for one loading point. Using the practical dynamic force and S-N curve, fatigue life of a window pillar is analyzed with FEM under the identified force by the procedure of above mentioned.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.2
• /
• pp.54-60
• /
• 1984

In this paper, the modified Hunt's constrained least squares estimation method for image restoration is studied with the parameter ${\alpha}$ which represents the effect of inverse filter, And it is akown that high frequency components in the restored image obtained by the proposed method are emphasized by optimizing the constraining factor ${\gamma}$, depending upon ${\alpha}$.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.5
• /
• pp.333-339
• /
• 1999

It is well recognized that ultrasonic technique is one of the most common and reliable nondestructive evaluation techniques for quantitative estimation of defects in structures. For the quantitative and accurate estimation of internal defects. the characteristics of scattered ultrasonic wavefields must be understood. In this study. the scattered near-field and far-field due to a circular cavity embedded in infinite media subjected to incident SH-waves were calculated by the boundary element method. The frequency response of the scattered ultrasonic far-field was transformed into the time-domain signal by obtaining its inverse Fourier transform. It was found that the amplitude of time-domain signal decreases and its time delay increases as the distance between the detecting point of ultrasonic scattered field and the center of internal cavity increases.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.8
• /
• pp.15-24
• /
• 2012

Even though decision of coefficient of horizontal subgrade reaction is important in analysis for pile under lateral load, the behavior of pile under lateral loading is estimated differently due to using established suggestion. Therefore this study estimates coefficient of horizontal subgrade reaction by using Chang's method or numerical inverse analysis method with the result of lateral load test. Then this study investigates the adequacy and reliability for coefficient of horizontal subgrade reaction. The analytical results of coefficient of horizontal subgrade reaction with lateral load test showed that coefficient of horizontal subgrade reaction with Chang's method was underestimated as compared with inverse analysis. Deformation modulus of foundation by Standard Specifications for Highway Bridges and Eo${\fallingdotseq}$1,400~1,600N showed similar range like range of coefficient of horizontal subgrade reaction with lateral load test.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.1
• /
• pp.1-11
• /
• 2014

In order to determine the optimal number of monitoring points in single-track tunnel lining, this thesis compares and evaluates the results of two cases: when the tunnel lining is modeled into a simple beam form and then is applied to 1) the tunnel lining inverse analysis program, and to 2) the commercially-used program. The displacement and stress of specific tunnel lining cross-sections are determined by entering the load conditions into the commercially-used program for tunnel interpretations. In doing so, two cases were assumed: where a symmetrically-distributed load was acting upon the tunnel lining of a single-track tunnel and where an asymmetrically-distributed load was in action. By comparing the computed displacement with the stress and displacement determined by entering side numbers 3, 5, and 7 into the tunnel lining inverse analysis program, the optimal number of monitoring points is determined. From the results of the research, it can be inferred that the number of monitoring points needs to be at least 5 points, considering the efficiency of monitoring in practice and the loss-and-damage rate of tunnel monitoring.

• The Journal of the Acoustical Society of Korea
• /
• v.17 no.4
• /
• pp.42-50
• /
• 1998

본 논문에서는 Gram-Schmidt 구조와 Inverse Power Method를 이용한 고유 부공간 추정 방법을 제안하고 입사각을 추정하는 문제에 적용하여 성능을 평가하였다. 그리고, 어레 이 센서들이 가운데를 중심으로 대칭으로 배열되어 있을 때, 전후방 GS 필터를 이용한 향 상된 고유 부공간 방법을 제안하였다. 그리고, 제안한 방법들을 제한조건을 갖는 gradient search 방법과 비교하였다.

• Journal of Korea Water Resources Association
• /
• v.37 no.12
• /
• pp.1009-1018
• /
• 2004

A systematic method using an optimal estimation algorithm is presented for simultaneous estimation of diffuse pollution distributed along a stream reach and model parameters for a stream water quality model. It was applied with the QVAL2E model to the South Han River for optimal estimation of kinetic constants and diffuse loads along the river. Initial calibration results for kinetic constants selected from a sensitivity analysis reveal that diffuse source inputs for nitrogen and phosphorus are essential to satisfy the system mass balance. Diffuse loads for total nitrogen and total phosphorus were estimated solving the expanded inverse problem. Comparison of kinetic constants estimated simultaneously with diffuse sources to those estimated without diffuse loads, suggests that diffuse sources must be included in the optimization not only for its own estimation but also for adequate estimation of the model parameters. Application of optimization method to river water quality modeling is discussed in terms of the sensitivity coefficient matrix structure.