• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 2000.06a
• /
• pp.243-248
• /
• 2000

Effect of NiO addition on microstructure, stability of tetragonal phase and mechanical properties was investigated. (Y, Ni)-TZP solid solution was obtained by pressureless sintering. The fracture toughness was increased by solid solution of NiO. Neither reaction phase nor glassy phase was observed at the grain boundaries. From these results, it was determined that solid solution of NiO was destabilized tetragonal phase of Y-TZP. Y-TZP/Ni nanocomposite that contained nano-sized Ni particles was also fabricated by internal reduction method. Some evaluations and discussions were carried out for both (Y, Ni)-TZP solid solution and Y-TZP/Ni nanocomposite.

• Advances in Energy Research
• /
• v.2 no.2
• /
• pp.73-84
• /
• 2014

Fuel cells of proton exchange membrane type (PEMFC) working with hydrogen in the anode and ambient air in the cathode ('air breathing') have been prepared and characterized. The cells have been studied with variable thickness of the cathode catalyst layer ($L_{CL}$), maintaining constant the platinum and ionomer loads. Polarization curves and electrochemical active area measurements have been carried out. The polarization curves are analyzed in terms of a model for a flooded passive air breathing cathode. The analysis shows that $L_{CL}$ affects to electrochemical kinetics and mass transport processes inside the electrode, as reflected by two parameters of the polarization curves: the Tafel slope and the internal resistance. The observed decrease in Tafel slope with decreasing $L_{CL}$ shows improvements in the oxygen reduction kinetics which we attribute to changes in the catalyst layer structure. A decrease in the internal resistance with $L_{CL}$ is attributed to lower protonic resistance of thinner catalyst layers, although the observed decrease is lower than expected probably because the electronic conduction starts to be hindered by more hydrophilic character and thicker ionomer film.

• Clinics in Shoulder and Elbow
• /
• v.9 no.2
• /
• pp.211-215
• /
• 2006

Reported in this article is a case report of a patients who developed limb threatening ischemia as a consequence of a subclavian artery thrombosis resulting from screws. The subclavian artery thrombosis after open reduction and internal fixation of clavicle fracture, when it occurs, should be treated promptly by plate removal and claviculectomy. It can be prevented by placing screws in locations away from the underlying neurovascular structures.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.5
• /
• pp.1043-1048
• /
• 2011

Test vector reordering is a very effective way to reduce power consumption during test application. But, it is time-consuming and complicated processes, and it does not consider internal circuit structure, which may limit the effectiveness. In this paper, we order test vectors using fanout count of primary inputs that consider the internal circuit structure, which may reduce the switching activity. Then, we reorder test test vectors again by using Hamming distance between test vectors. We proposed FOVO algorithm to perform these two ideas. FOVO is an effective way to reduce power consumption during test application. The algorithm is applied to benchmark circuits and we get an average of 3.5% or more reduction of the power consumption.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.39 no.2
• /
• pp.90-93
• /
• 2013

Mandibular fractures in infants are rare. This case report describes management of a mandibular fracture in an 11-month-old infant using a microplate and screws with open reduction. The surgical treatment was successful. Because the bone fragments were displaced and only the primary incisors had erupted, conservative treatment, such as an acrylic splint and circummandibular wiring, was not recommended. Nine weeks after surgery, the microplate was removed. The results showed complete clinical and radiological bone healing with normal eruption of deciduous teeth.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.6
• /
• pp.294-300
• /
• 1999

There is a growing interest in hybrid electric vehicles due to environmental concerns. Recent efforts are directed toward developing an improved main component systems for the hybrid electric vehicle applications. Soon after the introduction of electric starter for internal combustion engine early this century, despite being energy efficient and nonpolluting, electric vehicle lost the battle completly to internal combustion engine due to its limited range and inferior performance. Hybrid Electric vehicles offer the most promising solutions to reduce the emission of vehicles. This paper describes a method for cost reduction estimation of parallel hybrid electric vehicle. We used a cost reduction structure that consisted of five major subsystems (three-type and two-type motor) for parallel hybrid electric vehicle. Especially, we estimated the potential for cost reductions in parallel hybrid electric vehicle as a function of time using the learning curve. Also, we estimated the potentials of cost by depreciation.

• Journal of Korean Foot and Ankle Society
• /
• v.14 no.1
• /
• pp.105-107
• /
• 2010

The scanty literature on distal tibiofibular synostosis includes descriptions of relatively few specific complaints. Here we report a case of a 24-year-old young soldier who sustained a left ankle lateral malleolar fracture about 6 months ago and was initially treated by the open reduction and internal fixation with plate & screw. But 6 months later, he suffered from an vague ankle pain, each time the symptoms occurred right after an active ambulation, ankle dorsiflexion, especially when he had exercised aggressively. The radiographs revealed that there was a mature distal tibiofibular synostosis. We treated the patient with surgical excision of synostosis. Post-operative condition was satisfied to all concern and the result was found to be excellent during one-year follow-up.

• Clinics in Shoulder and Elbow
• /
• v.18 no.2
• /
• pp.105-112
• /
• 2015

In orthopedic trauma surgery, treatment of intraarticular distal humerus fractures is a challenge. With development of implants and biomechanical studies, surgical strategies with recommendations including preoperative computed tomography images, proper approaches and open reduction and internal fixation with dual plates have emerged. In addition, as an effort to provide stable fixation to permit early elbow motion, different methods of internal fixation, particularly plate configuration, have evolved. Using dual plates, either oriented parallel to each other or orthogonal, stable fixation has been achieved and satisfactory clinical outcomes have been reported. With rationales and advantages/disadvantages of each plate configuration, both techniques are selected according to surgeons' preference, and, in specific cases, one could be preferred over another. The key to successful fixation by either technique is obtaining anatomical reduction with restoration of two stable columns of the distal humerus.

• Transactions of Materials Processing
• /
• v.16 no.3 s.93
• /
• pp.157-162
• /
• 2007

The hydropiercing process gives a lot of advantages to the tube hydroforming such as cost reduction and high productivity. However it has a drawback, the amount of deflection around the hole is bigger than that of conventional die piercing process. The deflection can cause the problem at the assembly process of stamped parts and hydroformed part. Therefore the reduction of deflection is one of the most important issues for hydropiercing process. In this study, the deflection around hydropierced hole was investigated by experiment. As a result of investigation, the amount of deflection is influenced by the internal pressure, the material thickness' and the size of hole. Especially the hole size is most influencing factor on the deflection around the hydropierced hole.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.433-434
• /
• 2007

This paper describes a low-voltage dynamic random-access memory (DRAM) focusing on subthreshold leakage reduction during self-refresh (sleep) mode. By sharing a power switch, multiple iterative circuits such as row and column decoders have a significantly reduced subthreshold leakage current. To reduce the leakage current of complex logic gates, dual channel length scheme and input vector control method are used. Because all node voltages during the standby mode are deterministic, zigzag super-cutoff CMOS is used, allowing to Preserve internal data. MTCMOS technique Is also used in the circuits having no need to preserve internal data. Sub-1.2-V 1-Gb mobile DDR DRAM employing all these low-power techniques was designed in a 60 nm CMOS technology and achieved over 77% reduction of overall leakage current during the self-refresh mode.