• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.107-111
• /
• 2019

In FPD WET equipment, heaters are used a lot. There are many electric accidents caused by short circuit and overheating due to the use of heater, so it is necessary to have a safe electric system and interlock. Therefore, in this paper, we propose an electrical schematic and interlock for FPD WET equipment. In this paper, a hardware interlock such as a level sensor, an overheat protector, and an SSR heater sink is inserted, and the electric system is composed of ELB - MC - SSR - EOCR - heater. When the interlock occurs, the magnetic contactor (MC) is turned off and the power of the heater is cut off.EOCR, an electric overcurrent protection device, has an interlock to shut down the MC when there is an abnormality in the heater while checking the overcurrent, undercurrent and disconnection. These circuit configurations and interlocks are likely to be useful not only for WET equipment but also for any equipment in which the heater is placed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.5
• /
• pp.383-390
• /
• 2008

The SCR in Static Transfer Switch (STS) is used for reliability improvement of important load's power supply in industry field. However an average of 2% fault in thyristor(SCR) occurs, so that the attached mechanical switch is paralleled with SCR's both end points and SCR operates only during the $12{\sim}208$[mS] before operation of the mechanical switch. Also, an ISC (Ideal State Conditioning Interlock Device) - STS system that two power supply paths may not be thrown at the same time is developed to remove the overlap section perfectly when a short or earth fault is generated in one system. This method has reduced the fault rate remarkably through the reduction of SCR's fatigue degree by using SCR in conversion operation corresponding to 0.89 times a year. Also, in case of fault generations, it does not affect to supply power to the load, therefore it contributes to the promotion of reliability in the power supply.

• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.1913-1914
• /
• 2006

Modem Industrial control systems tend to adopt a variety of intelligent wireless device controllers to interface front-end computers with active components of the industrial device. Some of the intelligent control systems come equipped with a wireless SMS(Simple Message Service) interface giving an opportunity to use fault alarm Interlock system. Immediately send warning or alert messages to Mobile devices or remote users. Real time monitoring the SMS systems by Mobile devices. Control systems remotely by mobile devices in emergency situation. In order to provide against system fault, SMS Mobile System will enable system administrator to promptly access, monitor and control the system whenever users want and wherever users are, by utilizing wireless Internet and mobile devices. This paper presents the Mobile SMS system for PAL Control System.

• Structural Engineering and Mechanics
• /
• v.46 no.4
• /
• pp.487-504
• /
• 2013

In the present work a new friction device, with a set of single or double rotational friction flanges and a link element, is described and tested. The mechanism may be applied for the strengthening of existing r/c or steel buildings as well as in new constructed buildings. The device has selectable variable behavior in different levels of displacement and an interlock mechanism that is provided by the link element. The link element may be designed to lock at preselected level of displacement, offering in this way an extra safety reserve against strong earthquakes. A summary of the existing literature about other similar mechanisms is initially presented in this paper. The proposed mechanism is presented and described in details. Laboratory experiments are presented in detail and the resulted response that proves the efficiency of the mechanism at selectable levels of strength capacity is discussed. Drawings of the mechanism attached to a r/c frame with connection details are also included. Finally a dynamic analysis of two r/c frames, with and without the proposed mechanism attached, is performed and the resulted response is given. The main conclusion is that the proposed mechanism is a cheap and efficient devise for the improvement of the performance of new or existing framed buildings to seismic loads.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.3
• /
• pp.253-257
• /
• 2020

The local information processing devices are devices that process information by converting voltage, current, and digital electric signals from legacy-type power facility into IEC 61850 based data. It acquires and processes the operation information of legacy-type power facility, performs control of power facility, and interlock function using internal logic. In particular, the time to convert data to process input and output information for a device is important because a number of protection relay input and output signals are handled by only one device. This paper introduces test methods and cases for measuring IEC 61850 communication function and input/output data conversion time of local information processing device.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.4 no.4
• /
• pp.48-53
• /
• 2005

This research is materialized the mechanism of a interlocking elevator device to meet with customer's requirement demanding a variety of function. On this suitably theoretical translation and by considering of material significance of the most factor's tension spring and torsion spring, it's compared and reviewed the stress's calculation according that SWC and SWPB applied differently. And also that is approved through actual experiment. Out of a variety of feasible movement. Torque Balance is materialized by combination of tension spring, torsion spring and disk spring. So that application of 3 factors for optimal design is very important factor. In future, this research thesis make sure to play a highly role for application and improvement mechanically in various industry sector out of materializing interlock.

• Journal of the Korean Society of Safety
• /
• v.22 no.6
• /
• pp.1-6
• /
• 2007

A Recently elevator accidents were occurred and increased due to carelessness of user and violent behavior. The accident of door detachment in elevator platform by electronic motor scooter show a example of safety concerns and insensibility for safety awareness. In this report, we review the cause of accident of door detachment in elevator platform by electronic motor scooter, and show some suggestions of preventing from the safety concerns about this case.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.10
• /
• pp.17-26
• /
• 2010

This is concerned with the technology to monitor the vehicle operation, failure and disorder by using WiBro portable device. More precisely, the technology makes it possible that the information collection device is connected to both ECU(Electronic Control Unit) which is the device for controlling engine, transmission, brake, air-bag, etc that are connected to in-vehicle network and OBD-II connector that is for data collection from various sensors. In addition, with a WiBro portable device (cell phone, PDA, PMP, UMPC, etc). equipped with a vehicle diagnostic programs, information for operation, failure and malfunction can be obtained and analyzed in real-time, and alarm is alerted when the vehicle is in abnormal status, which makes the early reactions to the status. Furthermore, the collected data can be sent through WiBro network to the server managed by the company specialized in managing the vehicles, thus the technology could help the drivers who have less knowledge about their auto-vehicles have safe and economic driving. There is always a possibility of malfunction due to various types of noise that are caused by wring-harness when the device is wired-connected. In this research, in order to overcome this problem, we propose a system configuration that can do monitoring and diagnosis with a device for collecting data from vehicle and a personal WiBro device. Also, we performed research on data acquisition and interlock for the system defined by the definition for information and data sharing platform.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.205-210
• /
• 2014

This is concerned with the technology to display the design on Porcelain and adjust malfunction for moving effect and light intensity by curator. More precisely, the technology makes it possible that the porcelain is connected to Light module which is the device for controlling light emission and rotating rolling plate, etc that are connected to LED light module, optical fiber and controller that is for scenario from the given storytelling. In addition, with a WiFi portable device (Smart-phone, other mobile device). equipped with a scenario programs, information for operation, failure and malfunction can be obtained and analyzed in real-time, and menu color and alarm is alerted when the displaying design is in abnormal status, which makes the early reactions to the status. Furthermore, the collected data can be sent through WiFi network to the device and PC managed by the curator specialized in managing the design on the Porcelain, thus the technology could help the curator who have less knowledge about moving pattern on the Porcelain. There is always a possibility of malfunction due to various condition that are caused by wring-harness when modules are wired-connected. In this research, in order to overcome this problem, we propose a system configuration that can do monitoring and diagnosis with a device for collecting data from LED control module, Light emission sensor and a personal WiFi device. Also, we performed connection between optical Fiber and LED and interlock for the system defined by the definition for information and storytelling scenario.

• Journal of KIISE:Software and Applications
• /
• v.34 no.6
• /
• pp.530-538
• /
• 2007

Most existing deductive engines study for optimization of TBox based on Tableaux algorithm. However, in order to deduce mass-storing ABox in reality, it can't be decided in finite time. Therefore, for the efficiency of the deductive engine, there needs to be reasoning technique optimized for ABox. This paper uses the method that changes OWL-DL based Ontology to the form of Rule like Datalog in order to interlock store device such as RDBMS. Ultimately, it tries to in circumstance of real world. Therefor, using Axiom that OWL holds, it suggests reasoning method that applies rules including datatype.