• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04a
• /
• pp.31-34
• /
• 2004

During the last 20 years organic semiconductors have attracted considerable attention due to their interesting physical properties followed by various technological applications in the area of electronics and opto-electronics. It has been a long time since organic solar cells were expected as a low-cost energy-conversion device. Although practical use of them has not been achieved, technological progress continues. Morphology of the materials, organic/inorganic interface, metal cathodes, molecular packing and structural properties of the donor and acceptor layers are essential for photovoltaic response. We have fabricated solar cell devices based on zinc-phthalocyanine(ZnPc) as donor(D) and fullerine$(C_{60})$ as electron acceptor(A) with doped charge transport layers, $Alq_3$ as an electron transport or injection layer. We observed the photovoltaic characteristics of the solar celt devices using the Xe lamp as a light source.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2022-2024
• /
• 2005

Electrical double-layer capacitor (EDLC) is an electrochemical energy storage device in which electric charges only accumulated by a pure electrostatic attraction force are stored on the electrolyte-electrode interface in a form of double layer and separated by the electrolyte. The composite was prepared by mixing nanosize $TiO_2$ and activated carbon through a means of ultrasonic vibration in ethanol solution for 30 min in various mass ratios of $AC:TiO_2$ to form activated carbone-semiconducting oxide composites. Either 1.0 M $LiClO_4/EC-DEC$ or $Et_4NBF_4$/EC-DEC was used as the electrolyte. It was found that with modification of $TiO_2$, the specific capacitance of activated carbon measured at $1mA/cm^2$ was increased from 40 to 50 F/g. This method is unique in comparison the conventional method because it uses semiconducting TiO2 other than electrochemically active materials such as $RuO_2$. The increase in specific capacitance could be attributed to the decrease in electric polarization, caused by the introduction of $RuO_2$.

• Journal of Power Electronics
• /
• v.3 no.4
• /
• pp.230-238
• /
• 2003

Electric vehicles (EV) demands for greater acceleration, performance and vehicle range in pure electric vehicles plus mandated requirements to further reduce emissions in hybrid electric vehicles (HEV) increase the appeal for combined on-board energy storage systems and generators. And the power electronics plays an important role in providing an interface between fuel cells (FC) and loads. This paper deals with a multiple input DC-DC power converter devoted to combine the power flowing of multi-source on energy systems. The multi-source is composed of (i) FC system as a prime power demands, (ii) super capacitor banks as energy storage devices for high and intense power demands, (iii) superconducting magnetic energy storage system (SMES), (iv) multiple input DC-DC power converter and (v) a three phase inverter-fed permanent magnet synchronous motor as a drive. In this system, It is used super capacitor banks and superconducting magnetic energy replaces from the battery system. The modeling and transient performance simulation is effective for reducing transient influence caused by sudden charge of effective load. The main purpose of power electronic converters is to convert the DC power output from the fuel cell and other to a suitable AC voltage, which can be connected to electric loads directly (PMSM). The fuel cell and other output is connected to the DC-DC converter, which regulates the DC link voltage.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.509-510
• /
• 2007

The Breakdown properties of epoxy composites are used for transformers and sensor, which has been studied. As a result, From the measurements of breakdown voltage, the more hardener is increased the stronger breakdown strength at low temperature because the ester of hardener is increased. Breakdown strength at the high temperature is decreased because the temperature at $110^{\circ}C$ is near at $T_g$. When the filler is added, between epoxy and silica is formed interface. Therefore the charge is accumulated in it, and the electric field is concentrated, and breakdown strength is decreased than non-filled specimens. In the case of specimens, the treated with silane, the breakdown strength becomes much higher since this is suggested that silane coupling agent has been improved chemical bonding in the interfaces and has been relaxed the electric filed concentration.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.11
• /
• pp.2214-2218
• /
• 2009

Dye-sensitized solar cell (DSC) has been considered as a possible alternative to current silicon based p-n junction photovoltaic devices due to its advantages of high efficiency, simple fabrication process and low production cost. Numerous researches for high efficient DSC in the various fields are under way even now. Among them, the compact layer, which prevents the back electron transfer between transparent conductive oxides and the redox electrolyte, is fabricated by various methods such as a ZnO dip-coating, $TiCl_4$ dip-coating, and Ti sputtering. In this study, we tried to fabricate the $TiO_2$ compact layer by the spin-coating method using aqueous $TiCl_4$ solution. The effect of the spin-coating method was checked as compared with conventional dip-coating method. As a result, DSC with a spin-coated compact layer had 33.4% and 6% better efficiency than standard DSC and DSC with a dip-coated compact layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.751-754
• /
• 2000

When charge-trap SONOS cells are used flash memory, the tunneling program/erase condition to minimize the generation of interface traps was investigated. SONOSFET NVSM cells were fabricated using 0.35$\mu\textrm{m}$ standard memory cell embedded logic process including the ONO cell process. based on retrograde twin-well, single-poly, single metal CMOS process. The thickness of ONO triple-dielectric for memory cell is tunnel oxide of 24${\AA}$, nitride of 74 ${\AA}$, blocking oxide of 25 ${\AA}$, respectively. The program mode(Vg: 7,8,9 V, Vs/Vd: -3 V, Vb: floating) and the erase mode(Vg: -4,-5,-6 V, Vs/Vd: floating, Vb: 3V) by modified Fowler-Nordheim(MFN) tunneling were used. The proposed programming condition for the flash memory of SONOSFET NVSM cells showed less degradation($\Delta$Vth, S, Gm) characteristics than channel MFN tunneling operation. Also the program inhibit conditions of unselected cell for separated source lines NOR-tyupe flash memory application were investigated. we demonstrated that the program disturb phenomenon did not occur at source/drain voltage of 1 V∼4 V and gate voltage of 0 V∼4.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.181-184
• /
• 2004

Organic semiconductors have attracted considerable attention due to their interesting physical properties followed by various technological applications in the area of electronics and opto-electronics. It has been a long time since organic solar cells were expected as a low-cost high-energy conversion device. Although practical use of them has not been achieved, technological progress continues. Morphology of the materials, organic/inorganic interface, metal cathodes, molecular packing and structural properties of the donor and acceptor layers are essential for photovoltaic response. We have fabricated solar-cell devices based on copper-phthalocyanine(CuPc) as a donor(D) and fullerene($C_{60}$) as an electron acceptor(A) with doped charge transport layers, and BCP as an exciton blocking layer(EBL). We have measured photovoltaic characteristics of the solar-cell devices using the xenon lamp as a light source.

• Journal of Soil and Groundwater Environment
• /
• v.20 no.2
• /
• pp.41-46
• /
• 2015

The drag of the excess charge in an electrical double layer at the solid fluid interface due to water flow induces the streaming current, i.e., the streaming potential (SP). Here we introduce a sandbox experiment to study this hydroelectric coupling in case of a tracer test. An acrylic tank was filled up with homogeneous sand as a sand aquifer, and the upstream and downstream reservoirs were connected to the sand aquifer to control the hydraulic gradient. Under a steady-state water flow condition, a tracer test was performed in the sandbox with the help of peristaltic pump, and tracer samples were collected from the same interval of five screened wells in the sandbox. During the tracer test, SP signals resulting from the distribution of 20 nonpolarizable electrodes were measured at the top of the tank by a multichannel meter. The results showed that there were changes in the observed SP after injection of tracer, which indicated that the SP was likely to be related to the solute transport.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.272-272
• /
• 2013

The attractive features of photosynthetic reaction center proteins for energy application make them useful in solar energy conversion to hydrogen fuel or electrical energy. Almost unity charge separation quantum yield and its rapid speed of ~1ns, absorbance region in visible light (480~740 nm) and high proportion of photosynthetically active solar energy of 48.5% allowed photosystem1 to exploited as a bio-material for photo-energy devices. Directionality of photosystem1 in electron transfer can solve main problem in two-step water splitting process where back reaction deteriorates the overall efficiency. In the study, photosystem1 was extracted from spinach and the photo-induced excited electron in the reaction center was utilized in various field of light energy application. First, hydrogen evolving system realized by photodeposition of platinum at the end of the electron transfer chain, with combining specific semiconductor to oxidize water in the first step of Z-scheme. The evaluation by gas-chromatography demonstrated hydrogen evolution through the system. For the further application of photoelectrical material on electrode, photosystem1 have been controlled by copper ion, which is expected to assemble photosystem in specific orientation followed by maximized photoelectrical ability of film. The research proposed concrete methods for combining natural protein and artificial materials in one system and suggested possibility of designing interface between biological and inorganic materials.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.6
• /
• pp.574-581
• /
• 2012

Condition-based maintenance(CBM) has been used as a useful concept for optimizing maintenance plan and decreasing maintenance cost in several kinds of plant sites. This study introduced an example that developed an integrated management system for maintenance parameters and hydraulic turbine of hydro-power plant in order to improve its maintenance strategy as applying CBM techinique. The integrated management system consists of three parts. One is a hardware part including PDA inspection system and several kind of precision measuring instruments. Another is a vibration monitoring system on hydraulic turbine. The other is a software part that takes charge of making hierarchy tree of maintenance parameters and their inspection route, managing accumulated database, assessing health condition of components, and supporting interface with other enterprise management system. The system has been installed at Chuncheon hydro-power plant for test and demonstration. It is expected that the system can contribute database construction for diagnostics and prognostics on facility health condition and systematic accumulation of know-how on operation and maintenance of plant.