• 한국산업융합학회 논문집
• /
• 제7권2호
• /
• pp.207-213
• /
• 2004

This paper describes the development of Behind-Tape-Reader (BTR) type DNC system using CYBER 180-830 as a central computer and IBM PC-AT cell control computer and NC lathe with FANUC 5T NC controller. In this system, the connection between central computer and cell control computer is done via RS-232C serial interface board, and that between cell control computer and FANUC 5T controller is done via parallel interface board. The software consists of two module, central computer communication module for NC program downloading and status uploading, NC machine running module for NC operating.

• 유공압시스템학회:학술대회논문집
• /
• 유공압시스템학회 2010년도 춘계학술대회
• /
• pp.56-61
• /
• 2010

Simulator is a development equipment which enables the ECU to operate in normal mode by simulating the interface signal between ECU and mechanical system electrically. Embedded simulator means simulation function is embedded in ECU firmware, hence the electrical signal interface is replaced by the substitution of information at system program level. This paper explains the development of embedded transmission simulator for the verification of TCU firmware function which covers shifting control and on-board diagnosis. The embedded simulation program is executed in TCU processor along with the TCU firmware and it provides TCU firmware with not only the speed information those are appropriate both in driving and shifting conditions, but also the fault detection signals. Experimental results show that the validity of embedded simulator and its usefulness to the TCU firmware development and verification.

• Journal of the Optical Society of Korea
• /
• 제15권1호
• /
• pp.9-14
• /
• 2011

In this study, the internal structure of an optical waveguide embedded in a flexible optical circuit board is observed with a confocal microscope. In order to increase the light reflection from an internal material interface with a very small index difference, and thus enhance the signal contrast, a theta microscopy scheme has been integrated into a conventional confocal microscope, and a high NA oil-immersion lens has been used. The interface reflectivity is increased from roughly 0.0015% to 0.025% by the proposed method, and the internal structure can thus be successfully measured.

• 항공우주기술
• /
• 제4권2호
• /
• pp.79-87
• /
• 2005

본 논문은 차세대 위성을 위한 탑재컴퓨터 구조, 설계에 대한 논문이다. 차세대 위성용 탑재 컴퓨터는 MCMERC32SC CPU를 사용하고 중앙 집중 처리 구조를 채택하고 있다. 이를 위해 PM32 Module, TC-TM Module, IO Module 및 Power Module로 구성되어 있다. 각 Module간의 통신은 IEEE-1355 DS/DE(SpaceWire) 통신 방식을 채택하였다. 간단한 cross-strap 방법을 사용함으로서 모듈들의 잉여성 관리와 재사용성 증가를 손쉽게 할 수 있도록 하고 있다.

• 한국생산제조학회지
• /
• 제8권5호
• /
• pp.54-62
• /
• 1999

This paper describes the design and implementation of a PC(personal computer) based open architecture machine tool controller. The hardware of open architecture CNC has generally a motion control board on a PC for controlling a servo motor. But this paper describes open architecture hardware that consists of a PC, a counter board a DAC board and a DIO board only. This makes it easy to generate CNC software module in a hardware-independent way. The proposed open architecture CNC software runs on the MS-Windows NT. The paper describes a method of con-trolling servo motors using a real-time timer of MS-Windows NT and a commercial real-time operating system on the MS-Windows. NT. An open and reconfigurable software module is made up of an object and an API(application programming interface). Using the object and the API a new CNC system can be quickly configured to control dif-ferent machine tools. The proposed open architecture CNC system is applied to 4-axis lettering center.

• Steel and Composite Structures
• /
• 제9권1호
• /
• pp.1-17
• /
• 2009

This paper is focused on the buckling and post buckling behaviour of rectangular corrugated board panels simply supported and subjected to compression load. The aim of the work is to understand the failure mechanism of investigated structure in order to quantify the effect of design parameters on the strength of a panel of given geometry. Two numerical models were developed adopting the finite element method. In the first one the corrugated board is represented by means of shell elements adopting an equivalent material, in the second the local structure is described in full detail modelling both straight and corrugated layers by means of shell elements and representing the connection between layers by special interface elements. The model correctness was checked by the comparison between out of plane central displacement predicted by the models and the experimental values found in literature. For the same case the effect of panel planarity error was evaluated. Finally a parametric analysis to investigate the effect of design parameters was carried out.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제52권12호
• /
• pp.671-678
• /
• 2003

This paper proposes an expert system to generate automatically the test table of test system which can highly enhance the quality and productivity of product by inspecting quickly and accurately the defect device on the electronic circuit board tested. The expert system identifies accurately the tested components and the circuit patterns by tracing automatically the connectivity of circuit from electronic circuit database. And it generates automatically the test table to detect accurately the missing components, the misplaced components, and the wrong components for analog components such as resistance, coil, condenser, diode, and transistor, based on the experience knowledge of veteran expert. It is implemented in C computer language for the purpose of the implementation of the inference engine using the dynamic memory allocation technique, the interface with the electronic circuit database and the hardware direct control. And, the validity of the builded expert system is proved by simulating for a typical electronic board model.

• 전기학회논문지
• /
• 제58권10호
• /
• pp.1962-1967
• /
• 2009

This paper deals with a design of a platform to simulate PRT vehicle operational control algorithms using on-board embedded process board. The configuration of the platform is composed of the central control module, the station control module, man-machine interface and monitoring module. Since PRT system needs inherently very reliable vehicle operational control algorithm in order to avoid the impact between vehicles, it is very important to construct a simulation platform to test a designed vehicle operational control algorithm during the development process For the test of the proposed platform a path of the each moving vehicle is predefined in the central control system before the dispatch order is given to the vehicle. The simulation results show the effectiveness of the proposed simulation platform for test and evaluation of the PRT operational control algorithms.

• 제어로봇시스템학회논문지
• /
• 제16권4호
• /
• pp.374-380
• /
• 2010

This paper proposes a wearable interface for a tendon-driven robotic hand prosthesis. The proposed interface is composed of a dataglove to measure finger and wrist joint angle, and a micro-control board with a wireless RF module. The interface is used for posture control of the robotic hand prosthesis. The measured joint angles by the dataglove are transferred to the main controller via the wireless module. The controller works for directly controlling the joint angle of the hand or for recognizing hand postures using a pattern recognition method such as LDA and k-NN. The recognized hand postures in this study are the paper, the rock, the scissors, the precision grasp, and the tip grasp. In experiments, we show the performances of the wearable interface including the pattern recognition method.

• ETRI Journal
• /
• 제8권1호
• /
• pp.16-24
• /
• 1986

본고에서는 network controller인 82588을 이용한 EENET interface board로 IBM PC간의 LAN(Local Area Network)을 구성하고, 각 PC들간의 자원공유와 메세지 전송을 위한 network support programs의 개발에 관하여 기술한다.