• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2002.09a
• /
• pp.252-254
• /
• 2002

A new protocol for dosimetry in external beam radiotherapy is published by the Japan Society of Medical Physics (JSMP) in 2002. The protocol deals with proton and heavy ion beams as well as photon and electron beams, in accordance with IAEA Technical Report Series No. 398. To establish inter-institutional uniformity in proton beam dosimetry, an intercomparison program was carried out with the new protocol. The absorbed doses are measured with different cylindrical ionization chambers in a water phantom at a position of 30-mm residual range for a proton beam, that had range of 155 mm and a spread out Bragg peak (SOBP) of 60-mm width. As a result, the intercomparison showed that the use of the new protocol would improve the +/- 1.0 % (one standard deviation) and 2.7 % (maximum discrepancy) differences in absorbed doses stated by the participating institutions to +/- 0.3% and 0.9 %, respectively. The new protocol will be adopted by all of the participants.

• Journal of the Korean Geotechnical Society
• /
• v.27 no.11
• /
• pp.39-45
• /
• 2011

This study presents the thermal behaviors of glass beads-rubber mixtures depending on the volumetric fraction of each constituent and relative size between them. The transient plane source method is used to measure the effective thermal conductivity of mixtures. The discrete element method (DEM) and the thermal network model are integrated to investigate the particle-scale mechanism of heat transfer in granular packings. Results show that 1) the effective thermal conductivity decreases as the rubber fraction increases, and 2) the relative size between two solid particles dominates the spatial configuration of inter-particle contact condition that in tum determines the majority of heat propagation path through particle contacts. For the mixtures whose volumetric fraction of rubber is identical, the less conductive materials (e.g., rubber particles) with a large size facilitate heat transfer in granular materials. The experimental results and particle-scale observation highlight that the thermal conduction behavior is dominated not only by the volumetric fraction but also the spatial configuration of each constituent.

• Korean Journal of Materials Research
• /
• v.26 no.5
• /
• pp.229-234
• /
• 2016

In this study, the degree of particle melting in $Y_2O_3$ plasma spraying and its effects on coating characteristics have been investigated in terms of microstructural features, microhardness and scratch resistance. Plasma sprayed $Y_2O_3$ coatings were formed using two different powder feeding systems: a system in which the powder is fed inside the plasma gun and a system in which the powder is fed externally. The internal powder spraying method generated a well-defined lamellae structure that was characterized by a thin porous layer at the splat boundary and microcracks within individual splats. Such micro-defects were generated by the large thermal contraction of splats from fully-molten droplets. The external powder spraying method formed a relatively dense coating with a particulate deposition mode, and the deposition of a higher fraction of partially-melted droplets led to a much reduced number of inter-splat pores and intra-splat microcracks. The microhardness and scratch resistance of the $Y_2O_3$ coatings were improved by external powder spraying; this result was mainly attributed to the reduced number of micro-defects.

• Journal of Korea Foundry Society
• /
• v.23 no.5
• /
• pp.244-250
• /
• 2003

The aim of this study is fabricating of composite filler metal (CFM) by a combination of selective laser sintering (SLS) of stainless steel powders (RapidSteel $2.0^{TM}$ and liquid phase infiltration of Ag-28 wt.%Cu alloy. Porous stainless steel body with inter-connected pore channels was fabricated by SLS, binder decomposing and densification processes. By the direct contact infiltration, the narrow inter-particle channels of the porous body were completely filled with the Ag-28 wt.%Cu alloy infiltrant. During infiltration, the dissolved elements of Fe, Ni and Cr from the porous body were solved into copper solid solution phases, which consist of eutectic structure of composite metal matrix. The S10C/CFM/S10C joints, which have narrow clearance gaps between them up to 10 micrometers, were joined successfully by self-feeding of filler metal from the matrix of CFM. The CFM kept its original thickness and microstructure after brazing. The tensile strength of brazed specimen was higher than 30 kgf/$mm^2$ and showed a typical ductile fracture mode in the CFM.

• Nuclear Engineering and Technology
• /
• v.51 no.6
• /
• pp.1616-1625
• /
• 2019

Measuring occurrence times of random events, aimed to determine the statistical properties of the governing stochastic process, is a basic topic in science and engineering, and has been the subject of numerous mathematical modeling approaches. Often, true statistical properties deviate from measured properties due to the so called dead time phenomenon, where for a certain time period following detection, the detection system is not operational. Understanding the dead time effect is especially important in radiation measurements, often characterized by high count rates and a non-reducible detector dead time (originating in the physics of particle detection). The effect of dead time can be interpreted as a suitable rarefied sequence of the original time sequence. This paper provides a limit theorem for a high rate (diffusion-scale) counter with extendable (Type II) dead time, where the underlying counting process is a renewal process with finite second moment for the inter-event distribution. The results are very general, in the sense that they refer to a general inter arrival time and a random dead time with general distribution. Following the theoretical results, we will demonstrate the applicability of the results in three applications: serially connected components, multiplicity counting and measurements of aerosol spatial distribution.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.4 no.3
• /
• pp.246-253
• /
• 1999

Grain size distributions of sediment samples were analyzed by the different methods, and the results were compared. Reported data of the bottom sediments from the Korean seas show significant deviations among the institutes, and the inter-lab comparison and calibration procedures are considered to be necessary. Grain size data by different methods show different results. Laser diffraction method provides good precision in replicate analysis, but underestimates the amounts of finer (smaller than 2-3 ${\mu}m$) fraction. Data from particle settling method, on the other hand, represent significant errors in the coarse silt (5-6 ${\phi}$) fraction, and slightly overestimate the clay fraction. In the sieve and pipette methods, best results were taken in 0.5 ${\phi}$ interval of analysis. Especially in the coarse silt fraction, pipette analysis is suggested to be made with 0.5 ${\phi}$ interval. During the dry sieving procedure in 1 ${\phi}$ interval, serious errors occur when large amounts of sample materials were concentrated in a particular sieve.

• Proceedings of the Korean Environmental Health Society Conference
• /
• 2005.06a
• /
• pp.311-314
• /
• 2005

To evaluate the acute effects of fine particles on pulmonary function, a longitudinal study was conducted. This study was carried out for the schoolchildren(3rd and 4th grades) living in Inner-Mongolia, China. 113 Chinese children were asked to record their daily levels of peak expiratory flow rate(PEPR) using portable peak flow meter(mini-Wright) for 40 days and 3 time everyday(12 April 2004 to 21 May 2004). The atmospheric concentration of fine particles in study area was also determined everyday during same period. The relationship between dailypeak expiratory flow rate(PEFR) and fine particle levels was analyzed using a mixed linear regression models including gender, age, height, the presence of respiratory symptoms, and daily average relative humidity as extraneous variables. The analysis showed that the increase of fine particle concentrations was negatively associated with the variability in PEPR. The IQR(inter-quartile range) increments of $PM_{10}$ or $PM_{2.5}(66.0{\mu}g/m^3$ and $118.9{\mu}g/m^3$, respectively) were also shown to be related with 1.422L/min(95% Confidence intervals: 0.270 ${\sim}$ 2.574) and 1.214L1min(95% Cl: 0.010 ${\sim}$ 2.418) decline in PEFR.

• Environmental Engineering Research
• /
• v.25 no.3
• /
• pp.281-289
• /
• 2020

Environmental fate of ionizable organic pollutants such as perfluoroalkyl acids (PFAAs) are of increasing interest but has not been well understood because of uncertain values for parameters related with atmospheric interphase partitioning behavior. In the present study, not only the values for air-water partition coefficient (K_AW) and dissociation constant (pKa) of PFAAs were induced by adjusting to in situ measurements of air-water distribution coefficient between vapor phase and rainwater but also gas-particle partition coefficients were also estimated using three-phase partitioning model of ionizable organic pollutants, in situ measurements of PFAAs in aerosol and air vapor phase, and obtained parameter values. The pKa values of PFAAs we obtained were close to the minimum values suggested in literature except for perfluorooctane sulfonic acids, and COSMOtherm-modeled K_AW values were assessed to more appropriate among suggested values. When applying parameter values we obtained, it was predicted that air particle-associated fate and transport of PFAAs could be negligible and PFAAs could distribute ubiquitously along the transection from urban to rural region by pH-dependent phase transfer in air. Our study is expected to have some implications in prediction of the environmental redistribution of other ionizable organic compounds.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.37-40
• /
• 2003

As the integrated circuit device shrinks to the smaller dimension, the chemical mechanical polishing (CMP) process was required for the global planarization of inter-metal dielectric (IMD) layer with free-defect. However, as the IMD layer gets thinner, micro-scratches are becoming as major defects. Micro-scratches are generated by agglomerated slurry, solidified and attached slurry in pipe line of slurry supply system. It is well known that the presence of hard and larger size particles in the CMP slurries increases the defect density and surface roughness of the polished wafers. In this paper, we have studied aging effect the of CMP slurry as a function of particle size. We prepared and compared the self-developed silica slurry by adding of abrasives before and after annealing. As our preliminary experiment results, we could be obtained the relatively stable slurry characteristics comparable to original silica slurry in the slurry aging effect.

• Journal of KIISE:Computer Systems and Theory
• /
• v.32 no.1
• /
• pp.29-38
• /
• 2005

The fluid animation procedure consists of physical simulation and visual rendering. In the physical simulation of fluids, the most frequently used practices are the numerical simulation of fluid particles using particle dynamics equations and the continuum analysis of flow via Wavier-Stokes equation. Particle dynamics method is fast in calculation, but the resulting fluid motion is conditionally unrealistic The method using Wavier-Stokes equation, on the contrary, yields lifelike fluid motion when properly conditioned, yet the complexity of calculation restrains this method from being used in real-time applications. Global illumination is generally successful in producing premium-Duality rendered images, but is also excessively slow for real-time applications. In this paper, we propose a rapid fluid animation method incorporating enhanced particle dynamics simulation method and pre-integrated volume rendering technique. The particle dynamics simulation of fluid flow was conducted in real-time using Lennard-Jones model, and the computation efficiency was enhanced such that a small number of particles can represent a significant volume. For real-time rendering, pre-integrated volume rendering method was used so that fewer slices than ever can construct seamless inter-laminar shades. The proposed method could successfully simulate and render the fluid motion in real time at an acceptable speed and visual quality.