• Journal of the Society of Naval Architects of Korea
• /
• v.61 no.2
• /
• pp.115-124
• /
• 2024

To detect and prevent structural damage caused by various loads on marine structures and ships, structural health monitoring procedure is essential. Estimating loads acting on the structures which are measured by sensors that are mounted properly are crucial for structural health monitoring. However, attaching an excessive number of sensors to the structure without consideration can be inefficient due to the high costs involved and the potential for inducing structural instability. In this study, we introduce a method to determine the optimal number of sensors and their optimized locations for strain measurement sensors, allowing for accurate load estimation throughout the structure using model expansion method. To estimate the loads exerted on the entire structure with minimal sensors, we construct a strain-load interpolation matrix using the strain mode shapes of the finite element (FE) model and select the optimal sensor locations by applying D-Optimal Design and the row exchange algorithm. Finally, we estimate the loads exerted on the entire structure using the model expansion method. To validate the proposed method, we compare the results obtained by applying the optimal sensor placement and model expansion method to an FE model subjected to arbitrary loads with the loads exerted on the entire FE model, demonstrating efficiency and accuracy.

• Physical Therapy Korea
• /
• v.31 no.1
• /
• pp.79-88
• /
• 2024

Background: The abdominal drawing-in maneuver (ADIM), a method of lumbar stabilization training, is an effective neuromuscular intervention for lumbar instability associated with low back pain (LBP). Objects: The purpose of this study was to compare the effect of a 2-week period of the ADIM and tensor fasciae latae-iliotibial band (TFL-ITB) self-stretching on lumbopelvic rotation angle, lumbopelvic rotation movement onset, TFL-ITB length, and pain intensity during active prone hip lateral rotation. Methods: Twenty-two subjects with lumbar extension rotation syndrome accompanying shortened TFL-ITB (16 males and 6 females) were recruited for this study. The subjects were instructed how to perform ADIM training or ADIM training plus TFL-ITB self-stretching program at home for a 2-week period. A 3-dimensional ultrasonic motion analysis system was used to measure the lumbopelvic rotation angle and lumbopelvic rotation movement onset. An independent t-test was used to determine between-group differences for each outcome measure (lumbopelvic rotation angle, lumbopelvic rotation movement onset, TFL-ITB length, and pain intensity). Results: The results showed that ADIM training plus TFL-ITB self-stretching decreased the lumbopelvic rotation angle, delayed the lumbopelvic rotation movement onset, and elongated the TFL-ITB significantly more than did ADIM training alone. Pain intensity was lower in the ADIM training plus TFL-ITB self-stretching group than the ADIM training alone group; however, the difference was not significant. Conclusion: ADIM training plus TFL-ITB self-stretching performed for a 2-week period at home may be an effective treatment for modifying lumbopelvic motion and reducing LBP.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.30 no.1
• /
• pp.61-73
• /
• 2024

Background: The purpose of this study is to investigate the effect of ankle strengthening and proprioceptor exercise, including gluteus-medius strengthening exercise, on ankle strength, dynamic and static balance, ankle function, and quality of life in 24 adults without ankle instability. Methods: After randomly classifying 12 people per group into the experimental group and the control group, Home-exercise rehabilitation program was conducted for a total of 2 weeks. The control group performed ankle strengthening and proprioceptor exercise 5 times a week for 15 minutes, and the experimental group was performed by adding 15 minutes of gluteus-medius strengthning exercise to the exercise performed by the control group. The SPSS 27.0 program was used for statistical analysis. Results: Both groups showed statistically significant differences in the plantar flexion muscle strength, Y-Balance test, side hop test, quality of life. But, only experimental group showed statistically significant differences dorsi-flexion muscle strength and hip abduction muscle strength. There was no statistical difference in comparison of difference values between groups. Conclusion: These exercises can provide useful home rehabilitation programs for sports populations seeking to prevent injury in sports.

• Tribology and Lubricants
• /
• v.40 no.2
• /
• pp.39-46
• /
• 2024

The Morton effect (ME) is an instability phenomenon occurring in rotating machineries supported by fluid film bearings and is induced by the thermal deformation of the overhung mass, which is a part of the rotating shaft. Herein, we describe the ME during the high-speed balancing test of a 20 MW class steam turbine. Additionally, to predict the rotating speed at which the ME occurs, we apply the sensitivity vector theory for the steam turbine. During the operation of the steam turbine, we observe a continuous increase in vibration and hysteresis near the rated speed, which is typical of the ME. Increasing the temperature of the lubricating oil supplied to the bearings from 40 to 60℃ suppresses the occurrence of the ME. The rotordynamic analysis for the steam turbine suggests the existence of a mode in which the overhung mass undergoes significant deformation near the rated speed, and we presume that such a mode will increase the occurrence of the ME. The predicted rotating speed of ME occurrence, obtained through the sensitivity vector method, correlates with the test results. Moreover, increasing the temperature of the supplied lubricating oil mitigates the occurrence of ME by reducing the sensitivity between the temperature deviation vector and unbalance mass vector.

• Hip & pelvis
• /
• v.35 no.4
• /
• pp.268-276
• /
• 2023

Purpose: Resection remains the most reliable treatment for established heterotopic ossification, despite questions regarding its effectiveness due to the potential for complications. This study evaluated the clinical outcomes and complications of neurogenic heterotopic ossification (NHO) resection in stroke patients' ankylosed hips. Materials and Methods: We retrospectively analyzed nine hip NHO resections performed on seven patients from 2010 to 2018. The pre- and postoperative range of motion of the operated hip were compared. Analysis of postoperative complications, including infection, recurrence, iatrogenic fracture, and neurovascular injury was performed. Results: The mean operative time was 132.78±21.08 minutes, with a mean hemoglobin drop of 3.06±0.82 g/dL within the first postoperative week. The mean duration of postoperative follow-up was 52.08±28.72 months for all patients. Postoperative range of motion showed improvement from preoperative. Flexion and external rotation (mean, 58.89±30.60° and 16.67±18.03°, respectively) showed the greatest gain of motion of the operated hip joint. Postoperative infections resolved in two cases through surgical debridement, and one case required conversion to total hip arthroplasty due to instability. There were no recurrences, iatrogenic fractures, or neurovascular injuries. Conclusion: Resection is a beneficial intervention for restoring the functional range of motion of the hip in order to improve the quality of life for patients with NHO and neurological disorders. We recommend performance of a minimal resection to achieve a targeted functional arc of motion in order to minimize the risk of postoperative complications.

• Current Photovoltaic Research
• /
• v.12 no.1
• /
• pp.1-5
• /
• 2024

Perovskite solar cells have exhibited a remarkable increase in efficiency from an initial 3.8% to 26.1%, marking a significant advancement. However, challenges persist in the commercialization of perovskite solar cells due to their low stability with respect to humidity, light exposure, and temperature. Moreover, the instability of the organic charge transport layer underscores the need for exploring inorganic alternatives. In the manufacturing process of the perovskite solar cells' oxide charge transport layer, ultraviolet-ozone (UVO) treatment is commonly applied to enhance the wettability of the perovskite solution. The UVO treatment on metal oxides has proven effective in suppressing surface oxygen vacancies and removing surface organic contaminants. This study focused on the characterization of nickel oxide as the hole transport material in perovskite solar cells, specifically investigating the impact of UVO treatment on film properties. Through this analysis, changes induced by the UVO treatment were observed, and consequent alterations in the device characteristics were identified.

• Journal of the Korean Applied Science and Technology
• /
• v.41 no.1
• /
• pp.46-57
• /
• 2024

In this study, the various process conditions for high-power DC Magnetron Sputtering (DCMS) on the surface roughness of carbon thin films were investigated. The optimal conditions for Si/C coating were 40min for deposition time, which does not deviate from normal plasma, to obtain the maximum deposition rate, and the conditions for the best surface roughness were -16volt bias voltage and 400watt DC power with 1.3x10-3torr chamber pressure. Under these optimal conditions, an excellent carbon thin film with a surface roughness of 1.62nm and a thickness of 724nm was obtained. As a result of XPS analysis, it was confirmed that the GLC structure (sp² bonding) was more dominant than the DLC structure (sp³ bonding) in the thin film structure of the carbon composite layer formed by DC sputtering. Except in infrequent cases of relatively plasma instability, the lower bias voltage and applied power induces smaller surface roughness value due to the cooling effect and particle densification. For the optimal conditions for Graphite/C composite layer coating, a roughness of 36.3 nm and a thickness of 711 nm was obtained under the same conditions of the optimal process conditions for Si/C coating. This layer showed a immensely low roughness value compared to the roughness of bare graphite of 242 nm which verifies that carbon coating using DC sputtering is highly effective in modifying the surface of graphite molds for glass forming.

• Journal of Aerospace System Engineering
• /
• v.18 no.4
• /
• pp.34-42
• /
• 2024

This study developed a morphing technology applicable to unmanned aerial vehicles (UAVs) with diverse flight characteristics. Existing morphing technologies require additional mechanisms and driving devices, posing challenges in constructing features such as ribs and spars within the wing structure, leading to structural instability. To address this, we developed a Variable-Camber and Variable-Chord (VCC) morphing flap that could maintains a continuously transforming surface during deformation, altering both camber shape and chord length simultaneously. Furthermore, we conducted design and fabrication of UAV wings incorporating these morphing flaps, ensuring structural stability by developing specialized shapes. Furthermore, structural experiments were conducted to simulate flight loads, followed by actual flight tests to validate performances of both morphing mechanism and wings. Finally, wind tunnel tests were conducted to compare results with aerodynamic analysis, confirming the effective applicability of this morphing technology.

• Journal of Chest Surgery
• /
• v.42 no.4
• /
• pp.464-472
• /
• 2009

Background: We analyzed the clinical results and the factors for survival of patients who underwent extracorporeal life support system after adult cardiovascular surgery. Material and Method: We retrospectively reviewed the medical record of 44 patients (1.6% of the total adult cardiovascular surgical cases) who underwent the use of a ventricular assisted device or extracorporeal membrane oxygenation from January 2002 to August 2008. There were 32 (72.7%) males and their mean age was 61.7$\pm$14.9(range: 20$\sim$73) years old. The mean duration of extracorporeal life support system was 5.3$\pm$3.0 (range: 1$\sim$12) days. Result: Of these 44 patients, 24 (54.5%) patients were successfully weaned from the extracorporeal device. Eighteen (40.9%) survivors were able to be discharged from the hospital. Complications were noted in 38 patients (86.4%). An emergency operation, no usage of a concomitant intraaortic balloon pump and major complications during use of the extra corporeal life support system such as bleeding, flow instability and renal failure were identified as significant risk factors for poor survival on univariated analysis. Owing to educational support and a continuous renal replacement therapy system, the clinical outcomes of these patients have improved since 2006. On multivariated analysis, renal failure and bleeding during extracorporeal life support were significant risk factors for poor survival. Conclusion: Although using. extracorporeal life support systems after adult cardiovascular surgery revealed acceptable clinical results, determining the optimal treatment strategy and further well designed larger studies are needed to improve the survival rate of patients who undergo extracorporeal life support after adult cardiovascular surgery.

• KDI Journal of Economic Policy
• /
• v.12 no.4
• /
• pp.21-46
• /
• 1990

This paper, a sequel to Yoo and Lee (1990), attempts to investigate the interindustry determinants of technical efficiency in Korea's manufacturing industries, and also to conduct an exploratory analysis on the stability of technical efficiency over time. The hypotheses set forth in this paper are most found in the existing literature on technical efficiency. They are, however, revised and shed a new light upon, whenever possible, to accommodate any Korea-specific conditions. The set of regressors used in the cross-sectional analysis are chosen and the hypotheses are posed in such a way that our result can be made comparable to those of similar studies conducted for the U.S. and Japan by Caves and Barton (1990) and Uekusa and Torii (1987), respectively. It is interesting to observe a certain degree of similarity as well as differentiation between the cross-section evidence on Korea's manufacturing industries and that on the U.S. and Japanese industries. As for the similarities, we can find positive and significant effects on technical efficiency of relative size of production and the extent of specialization in production, and negative and significant effect of the variations in capital-labor ratio within industries. The curvature influence of concentration ratio on technical efficiency is also confirmed in the Korean case. There are differences, too. We cannot find any significant effects of capital vintage, R&D and foreign competition on technical efficiency, all of which were shown to be robust determinants of technical efficiency in the U.S. case. We note, however, that the variables measuring capital vintage effect, R&D and the degree of foreign competition in Korean markets are suspected to suffer from serious measurement errors incurred in data collection and/or conversion of industrial classification system into the KSIC (Korea Standard Industrial Classification) system. Thus, we are reluctant to accept the findings on the effects of these variables as definitive conclusions on Korea's industrial organization. Another finding that interests us is that the cross-industry evidence becomes consistently strong when we use the efficiency estimates based on gross output instead of value added, which provides us with an ex post empirical criterion to choose an output measure between the two in estimating the production frontier. We also conduct exploratory analyses on the stability of the estimates of technical efficiency in Korea's manufacturing industries. Though the method of testing stability employed in this paper is never a complete one, we cannot find strong evidence that our efficiency estimates are stable over time. The outcome is both surprising and disappointing. We can also show that the instability of technical efficiency over time is partly explained by the way we constructed our measures of technical efficiency. To the extent that our efficiency estimates depend on the shape of the empirical distribution of plants in the input-output space, any movements of the production frontier over time are not reflected in the estimates, and possibilities exist of associating a higher level of technical efficiency with a downward movement of the production frontier over time, and so on. Thus, we find that efficiency measures that take into account not only the distributional changes, but also the shifts of the production frontier over time, increase the extent of stability, and are more appropriate for use in a dynamic context. The remaining portion of the instability of technical efficiency over time is not explained satisfactorily in this paper, and future research should address this question.