• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.494-498
• /
• 1996

Three fuzzy input space partitoining methods, which are grid, tree, and scatter method, are mainly used until now. These partition methods represent good performance in the modeling of the linear system and nonlinear system with independent modeling variables. But in the case of the nonlinear system with the coupled modeling variables, there should be many fuzzy rules for acquiring the exact fuzzy model. In this paper, it shows that the fuzzy model is acquired using transformed modeling vector by linear transformation of the modeling vector.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.5
• /
• pp.36-44
• /
• 1993

In this paper, a simple design method is represented for a contiguous-band waveguide manifold diplexer which employs a half-wavelength line at the input port of the singly terminated bandpass filterand has resonant-slot coupled E-plane T-junctions. This design method is based on the fact that the input impedance characteristics of the singly terminated bandpass filter are approximately unchanged when a resonant slot and a half-wavelength line at the input port of the filter are employed. This design method is also applicable to the design of the multiplexer. A contiguous-band waveguide manifold diplexer using the post coupled cavity filters is designed, constructed, and tested. The computed and experimental results show the validity of the theory.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.2
• /
• pp.85-91
• /
• 2022

This study proposes a high efficiency bridgeless Power Factor Correction (PFC) converter with improved common mode noise characteristics. Conventional PFC has limitations due to low efficiency and enlarged heat sink from considerable conduction loss of bridge diode. By applying a Common Mode (CM) coupled inductor, the proposed bridgeless PFC converter generates less conduction loss as only a small magnetizing current of the CM coupled inductor flows through the input diode, thereby reducing or removing heat sink. The input diode is alternately conducted every half cycle of 60 Hz AC input voltage while a negative node of AC input voltage is always connected to the ground, thus improving common mode noise characteristics. With the aim to improve switching loss and reverse recovery of output diode, the proposed circuit employs Critical Conduction Mode (CrM) operation and it features a simple Zero Current Detection (ZCD) circuit for the CrM. In addition, the input current sensing is possible with the shunt resistor instead of the expensive current sensor. Experimental results through 480 W prototype are presented to verify the validity of the proposed circuit.

• The Journal of the Acoustical Society of Korea
• /
• v.17 no.1E
• /
• pp.14-19
• /
• 1998

This article describes the application of a coupled finite element-boundary element method to obtain the steady-state response of a sonar transducer. The sonar shell is simulated to be driven by electrical charges applied onto inner and outer surfaces of the shell. It is shown that at relatively low input frequency a beam pattern which is almost close to omnidirection can be obtained. The coupled FE-BE method is described in detail.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.1
• /
• pp.37-43
• /
• 1998

This article describes the application of a coupled finite element-boundary element method to obtain the steady-state response of a sonar transducer. The particular structure considered is a flooded piezoelectric spherical shell. The sonar shell is simulated to be driven by electrical charges applied onto inner and outer surfaces of the shell. It is shown that at relatively low input frequency a beam pattern which is almost close to omnidirection can be obtained. The coupled FE-BE method is described in detail.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.465-468
• /
• 1988

A n-well CMOS Operational Transconductance Amplifier -C(OTA-C) integrator with a wide linear input range is designed. The circuit designed has superior linearity of input voltage range compared with the conventional source-coupled pair OTA. The OTA developed in this paper is versatile in application: diverse applications are in the fields of linear amplifiers, continuous-time filters, gain control circuits, and analog multipliers, etc..

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1100-1107
• /
• 2004

In this paper, a new design method fur tapped coupled-line filters has been developed. The design equations for this tapped-line filter have been obtained using a new equivalent circuit model of tapped lines. These tapped-lines replace input/output coupled lines of the conventional edge coupled-line filters, which tend to have very narrow line gaps(few mils). Therefore, tapped coupled-line filters tend to be less sensitive to filter fabrication tolerances and to be easily fabricated using milling tools. The new filter design algorithm allows very accurate filter design for frequencies up to 20 GHz and bandwidth less than 20 %.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.327-337
• /
• 2015

This study discusses the design of a parallel-operated DC-DC single-ended primary-inductor converter (SEPIC) for low-voltage application and current sharing with a constant output voltage. A coupled inductor is used for parallel-connected SEPIC topology. Generally, two separate inductors require different ripple currents, but a coupled inductor has the advantage of using the same ripple current. Furthermore, tightly coupled inductors require only half of the ripple current that separate inductors use. In this proposed work, tightly coupled inductors are used. These produce an output that is more efficient than that from separate inductors. Two SEPICs are also connected in parallel using the coupled inductors with a single common controller. An analog control circuit is designed to generate pulse width modulation (PWM) signals and to fulfill the closed-loop control function. A stable output current-sharing strategy is proposed in this system. An experimental setup is developed for a 18.5 V, 60 W parallel SEPIC (PSEPIC) converter, and the results are verified. Results indicate that the PSEPIC provides good response for the variation of input voltage and sudden change in load.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.114-120
• /
• 2008

This paper proposed the band pass filter(BPF) with feeding structure using $\pi$-type transmission line by means of transforming the input/output coupled-lines of the half wavelength parallel coupled-line BPF into K-inverter, then substituting $\pi$-type transmission line equivalence for K-inverter. The proposed method supplies solution with what the half wavelength parallel coupled-line BPF's input/output coupled-lines are realized. Also it can quite reduce efforts and time needed to optimize filter performance when is compared to reported method using tapped line structure because formulas is very simple and accurate. On the basic of the proposed method, the BPF with feeding structure using $\pi$-type transmission line has been designed and fabricated. The validity of proposed method was proven by the measured result.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.5 s.149
• /
• pp.597-603
• /
• 2006

The estimations of distributed and joint-excited input power for Power Flow Analysis are accomplished in this paper. Using Fourier transform, the displacements of infinite structures are derived, and the input power of distributed excitation can be estimated. The obtained results compare the real input power with the estimation of input power. When the exciting force acts on the joint of coupled structures, it is estimating the power that is transferred to each structure. Appling this input power, the results of energy density and intensity of Power Flow Analysis can be compared with the classical solutions.