• Korean Journal of Materials Research
• /
• v.29 no.11
• /
• pp.684-689
• /
• 2019

Single crystals, which have complexed composition, are fabricated by solid state grain growth. However, it is hard to achieve stable properties in a single crystal due to trapped pores. Aerosol deposition (AD) is suitable for fabrication of single crystals with stable properties because this process can make a high density coating layer. Because of their unique features (nano sized grains, stress inner site), it is hard to fabricate single crystals, and so studies of grain growth behavior of AD film are essential. In this study, a $BaTiO_3$ coating layer with ${\sim}9{\mu}m$ thickness is fabricated using an aerosol deposition method on (100) and (110) cut $SrTiO_3$ single crystal substrates, which are adopted as seeds for grain growth. Each specimen is heat-treated at various conditions (900, 1,100, and $1,300^{\circ}C$ for 5 h). $BaTiO_3$ layer shows different growth behavior and X-ray diffraction depending on cutting direction of $SrTiO_3$ seed. Rectangular pillars at $SrTiO_3$ (100) and laminating thin plates at $SrTiO_3$ (110), respectively, are observed.

• Korean Journal of Plant Resources
• /
• v.13 no.1
• /
• pp.48-53
• /
• 2000

Lacquer tree can be proliferated by root or stem cutting, and seed. In case of proliferation by seed, however, the germination rate is very low. Thus, the present study was carried out to obtain aspceptic lacquer plant in vitro from seed because natural tissue culture was highly defiled by unknown fungi and bacteria. First seed grading on distilled water was 50.7% and second seed grading was 20.8% after 98% sulfuric acid treatment for 2 hours. Removal of inner seed coat was higher with 32.4% than non-removal of outer seed coat and removal outer seed coat in rooting rate. In germination rate according to pre-treatment, growth regulators were not effective at all, but sulfuric acid was effective a little with 3%. Removal outer seed coat was increased about 4%, that germinated about 10% in MS medium supplemented with 1.0mg/L BA and 0.05mg/L NAA, 1.0mg/L BA. Lacquer tree seeds germinated after 10 days in MS medium, and aspceptic seedling of lacquer tree were obtained after 3 weeks in vitro. Germination rate, however, was lower about 10%.

• International Journal of Highway Engineering
• /
• v.10 no.3
• /
• pp.109-118
• /
• 2008

This study analyzes the change of stability of embankment due to the construction of embankment combined used road with two different construction phases. The stabilities have been checked both in the phase of earth banking for a road construction and in the phase of the application of the traffic roads(DB-24). In both cases the factor of safety has been found higher than 1.3 which is the general criterion of the safety of an embankment. The results indicate that the safety of an embankment due to the construction of embankment combined use road is assured, and thus, it is thought that the construction of embankment combined use road can be considered for cutting down on expenses of construction sites for a road construction. However, the pre-examination of stability due to the construction should be carried out because it decreases the factor of safety of an embankment. From this study, it has been found that the factor of safety was dropped most when the water level rose in the transient flow. The result indicates that the stability analysis of a river embankment where the water level changes frequently should be carried out in the condition of transient flow. It is recommended that the inner side of an embankment should have a slope of 1:2 which is identical with the slope of the existing embankment. In addition, the factor of safety also can be decreased due to the traffic loads, and therefore, the effect should also be considered after the construction of embankment combined used road limiting the traffic loads.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.62-62
• /
• 2018

Pt is still considered as one of the most active electrocatalysts for ORR in alkaline fuel cells. However, the high cost and scarcity of Pt hamper the widespread commercialization of fuel cells. As a strong candidate for the replacement of Pt catalyst, silver (Ag) has been extensively studied due to its high activity, abundance, and low cost. Ag is more stable than Pt in the pH range of 8~14 as the equilibrium potential of Ag/Ag+ being ${\approx}200mV$ higher than that of Pt/PtO. However, Ag is the overall catalytic activity of Ag for oxygen reduction reaction(ORR) is still not comparable to Pt catalyst since the surface Ag atoms are approximately 10 times less active than Pt atoms. Therefore, further enhancement in the ORR activity of Ag catalysts is necessary to be competitive with current cutting-edge Pt-based catalysts. We demonstrate the architectural design of Ag catalysts, synthesized using plasma discharge in liquid phase, for enhanced ORR kinetics in alkaline media. An attractive feature of this work is that the plasma status controlled via electric-field could form the Ag nanowires or dendrites without any chemical agents. The plasma reactor was made of a Teflon vessel with an inner diameter of 80 mm and a height of 80 mm, where a pair of tungsten(W) electrodes with a diameter of 2 mm was placed horizontally. The stock solutions were made by dissolving the 5-mM AgNO3 in DI water. For the synthesis of Agnanowires, the electricfield of 3.6kVcm-1 in a 200-ml AgNO3 aqueous solution was applied across the electrodes using a bipolar pulsed power supply(Kurita, Seisakusyo Co. Ltd). The repetition rate and pulse width were fixed at 30kHz and 2.0 us, respectively. The plasma discharge was carried out for a fixed reaction time of 60 min. In case of Ag nanodendrites, the electric field of 32kVcm-1 in a 200-ml AgNO3 aqueous solution was applied and other conditions were identical to the plasma discharge in water in terms of electrode configuration, repetition rate and discharge time. Using SEM and STEM, morphology of Ag nanowires and dendrites were investigated. With 3.6 kV/cm, Ag nanowire was obtained, while Ag dendrite was constructed with 32 kV/cm. The average diameter and legth of Ag nanowireses were 50 nm and 3.5 um, and thoes values of Ag dendrites were 40 nm and 3.0 um. As a results of XPS analysis, the surface defects in the Ag nanowires facilitated O2 incorporation into the surface region via the interaction between the oxygen and the electron cloud of the adjacent Ag atoms. The catalytic activity of Ag for oxygen reduction reaction(ORR) showed that the catalytic ORR activity of Ag nanowires are much better than Ag nanodendrites, and electron transfer number of Ag nanowires is similar to that of Pt (${\approx}4$).

• Journal of the Korean Geographical Society
• /
• v.42 no.3 s.120
• /
• pp.388-404
• /
• 2007

This study interprets evolution of fluvial terraces along the four Yeongdong- and Yeongseo streams such as Naerin River, Yeongok River, Golji River and Osip River, in Gangwon Province based on the tectonics. The results from the analyses of the distribution pattern of fluvial terraces and incision rates of rivers show distinctively the evidence as the axis of uplift by Taebaek Mountains, especially on the 4th, 5th and 6th terraces in upper reach of Osip River among the four streams. The axis of uplift extends to the zone of $30\sim40km$ in width as well as the divide. The difference of uplift between upper and middle reaches of Naerin River and total reach of Golji River wasn't found from the height from riverbed by the active uplifting along all reaches, estimated to be set in inner area of uplift zone. Incision rate of period between formation age of 2nd terrace and 1st terrace is calculated $0.13\sim0.22m/ka$, and incision rate of period between formation age of 1st terrace and Present is diversely calculated $0.17\sim0.27m/ka$ by the climatic discrepancy between the two periods. The incision rate of Yeongdong streams whose mouths reach to the sea level eroded actively more than Yeongseo streams in the uplift zone. And Yeongdong streams between formation age of 1th terrace and present appears to much higher than that of Yeongseo streams, due to active down-cutting in oder to balance against the sea level.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.401-405
• /
• 2006

A uniform velocity field of crust can be obtained by cumulative multi-year GPS data. Then the shortening and sliding of drape zones between Chinese Continent Blocks can be researched through the velocity field and dynamics meaning is also analyzed. A model of movement and strain is created to extract displacing and rotating information of blocks in this paper. On the basis of it, the shortening vectors and sliding states of drape zones between blocks can be obtained by the model of level center of gravity moving velocity vectors between neighboring blocks. Some result show as follows. India plate jostles greatly toward north, so a complicated movement situation is formed for 14 sub-blocks. And self-deformations of inner tectosomes can be greatly reflected according to the characteristics of drape zones between tectosomes. The extrusion deformation exists between Himalaya and Qiangtang blocks. Its contraction ratio is about 20.1 $mm.a^{-1}$. However, it only is $mm.a^{-1}$ between Tarim and Zhungar. The deformation characteristics and contraction ratio of other drape zones are obviously different with the former. The movement characteristics of contraction, shear, dislocation, etc. are showed in these zones. The average contraction ratio is about 5.0 $mm.a^{-1}$. The whole trend in the west continent has a big movement toward north, and in the east continent has a small movement toward south or southeast. The strain of west continent is far bigger than that of east, and the strain of southwest is bigger than that of the southeast. It is whole showed that India plate jostles toward north-east and the south-north zone has cutting and absorbing phenomena. The total characteristics and present-day trends of deformation of inland drape zones are basically described by the sinistrorse dislocation in south-north zone and Arjin fracture, the sinistrorse shear between south china and north china, etc.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.3 no.3
• /
• pp.45-76
• /
• 2000

The purposes of this study were to investigate and understand the present status of various types of "deserts", such as sand desert, gravel desert, rock desert, earth desert, salt desert, desert, rocky desert, gobi desert, sandy desert, clay desert, etc., and the general countermeasures for the combating "desertification" "desertization", and to develop the technologies on the revegetation and restoration for the combating desertification in China. The methods of this study were mainly composed of field surveys on the several experimental sites and research institutes related to combating desertification in China, and examinations on the various technologies for the combating desertification at the Daxing Experimental Station of Beijing Forestry University. The conclusion from this study may be summarized as follows; 1. Status and tendency of desertification in China : China is one of the countries seriously threatened by desertification. Desertification affected areas in China are mainly distributed in arid, semi-arid and dry sub-humid areas in China, covering the most regions of the Northeast China (eastern region of Inner-Mongolia), the northern part of the North China (middle and western region of Inner-Mongolia, Shaanxi, Ningsha, Gansu) and the western part of the Northwest China (Xinzang, Qinghai, Xizang). The total area affected by desertification in China is approximately 2.622 million $km^2$. It covers 27.3% of the total territory of China. Until recently, it is estimated that the annual spreading ratio of desertification in China is 2,460 $km^2$. Therefore, desertification is mostly serious problems facing to the Chinese people. 2. The causes and environmental effect of desertification : The desertification in China is mainly caused by compound factors, including natural condition and human activities. In China, the desertification is started by the decrease of precipitation, continuous dry and drought, strong wind, wind and water erosion, land degradation and loss of natural vegetation caused by climate variation, and accelerated by the human activities, such as over-cultivating, over-grazing, over-cutting of woods, irrational use of water resources. Because desertification has affected the geographical features, soil nutrients contents, salinity, vegetation coverage and the functions of ecosystem, the environmental deteriorations in the desertification affected areas are very seriously. 3. The fundamental strategies of combating desertification in China are the increase of education and awareness of people through various mass media, the revision of laws to guarantee operation of Desertification Combating Law and to improve many relating laws and regulations, the application of advanced technologies and training of experts, the establishment of discriminative policies, and increasing arrangement of budget-investment, and so on. China, as a signed country in UNCCD, has made efforts for the combating desertification. Korea is also signed country in UNCCD, so we should play an important role in the desertification combating projects of China for the northest asia and global environmental conservation as well as environmental conservation of Korea.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.20 no.1
• /
• pp.4592-4598
• /
• 1978

The purpose of this research is to find out mathemetically an economical intake water depth in the design of head works through the derivation of some formulas. For the performance of the purpose the following formulas were found out for the design intake water depth in each flow type of intake sluice, such as overflow type and orifice type. (1) The conditional equations of !he economical intake water depth in .case that weir body is placed on permeable soil layer ; (a) in the overflow type of intake sluice, {{{{ { zp}_{1 } { Lh}_{1 }+ { 1} over {2 } { Cp}_{3 }L(0.67 SQRT { q} -0.61) { ( { d}_{0 }+ { h}_{1 }+ { h}_{0 } )}^{- { 1} over {2 } }- { { { 3Q}_{1 } { p}_{5 } { h}_{1 } }^{- { 5} over {2 } } } over { { 2m}_{1 }(1-s) SQRT { 2gs} }+[ LEFT { b+ { 4C TIMES { 0.61}^{2 } } over {3(r-1) }+z( { d}_{0 }+ { h}_{0 } ) RIGHT } { p}_{1 }L+(1+ SQRT { 1+ { z}^{2 } } ) { p}_{2 }L+ { dcp}_{3 }L+ { nkp}_{5 }+( { 2z}_{0 }+m )(1-s) { L}_{d } { p}_{7 } ] =0}}}} (b) in the orifice type of intake sluice, {{{{ { zp}_{1 } { Lh}_{1 }+ { 1} over {2 } C { p}_{3 }L(0.67 SQRT { q} -0.61)}}}} {{{{ { ({d }_{0 }+ { h}_{1 }+ { h}_{0 } )}^{ - { 1} over {2 } }- { { 3Q}_{1 } { p}_{ 6} { { h}_{1 } }^{- { 5} over {2 } } } over { { 2m}_{ 2}m' SQRT { 2gs} }+[ LEFT { b+ { 4C TIMES { 0.61}^{2 } } over {3(r-1) }+z( { d}_{0 }+ { h}_{0 } ) RIGHT } { p}_{1 }L }}}} {{{{+(1+ SQRT { 1+ { z}^{2 } } ) { p}_{2 } L+dC { p}_{4 }L+(2 { z}_{0 }+m )(1-s) { L}_{d } { p}_{7 }]=0 }}}} where, z=outer slope of weir body (value of cotangent), h1=intake water depth (m), L=total length of weir (m), C=Bligh's creep ratio, q=flood discharge overflowing weir crest per unit length of weir (m3/sec/m), d0=average height to intake sill elevation in weir (m), h0=freeboard of weir (m), Q1=design irrigation requirements (m3/sec), m1=coefficient of head loss (0.9∼0.95) s=(h1-h2)/h1, h2=flow water depth outside intake sluice gate (m), b=width of weir crest (m), r=specific weight of weir materials, d=depth of cutting along seepage length under the weir (m), n=number of side contraction, k=coefficient of side contraction loss (0.02∼0.04), m2=coefficient of discharge (0.7∼0.9) m'=h0/h1, h0=open height of gate (m), p1 and p4=unit price of weir body and of excavation of weir site, respectively (won/㎥), p2 and p3=unit price of construction form and of revetment for protection of downstream riverbed, respectively (won/㎡), p5 and p6=average cost per unit width of intake sluice including cost of intake canal having the same one as width of the sluice in case of overflow type and orifice type respectively (won/m), zo : inner slope of section area in intake canal from its beginning point to its changing point to ordinary flow section, m: coefficient concerning the mean width of intak canal site,a : freeboard of intake canal. (2) The conditional equations of the economical intake water depth in case that weir body is built on the foundation of rock bed ; (a) in the overflow type of intake sluice, {{{{ { zp}_{1 } { Lh}_{1 }- { { { 3Q}_{1 } { p}_{5 } { h}_{1 } }^{- {5 } over {2 } } } over { { 2m}_{1 }(1-s) SQRT { 2gs} }+[ LEFT { b+z( { d}_{0 }+ { h}_{0 } )RIGHT } { p}_{1 }L+(1+ SQRT { 1+ { z}^{2 } } ) { p}_{2 }L+ { nkp}_{5 }}}}} {{{{+( { 2z}_{0 }+m )(1-s) { L}_{d } { p}_{7 } ]=0 }}}} (b) in the orifice type of intake sluice, {{{{ { zp}_{1 } { Lh}_{1 }- { { { 3Q}_{1 } { p}_{6 } { h}_{1 } }^{- {5 } over {2 } } } over { { 2m}_{2 }m' SQRT { 2gs} }+[ LEFT { b+z( { d}_{0 }+ { h}_{0 } )RIGHT } { p}_{1 }L+(1+ SQRT { 1+ { z}^{2 } } ) { p}_{2 }L}}}} {{{{+( { 2z}_{0 }+m )(1-s) { L}_{d } { p}_{7 } ]=0}}}} The construction cost of weir cut-off and revetment on outside slope of leeve, and the damages suffered from inundation in upstream area were not included in the process of deriving the above conditional equations, but it is true that magnitude of intake water depth influences somewhat on the cost and damages. Therefore, in applying the above equations the fact that should not be over looked is that the design value of intake water depth to be adopted should not be more largely determined than the value of h1 satisfying the above formulas.

• Journal of Applied Tourism Food and Beverage Management and Research
• /
• v.13 no.2
• /
• pp.45-69
• /
• 2002

This study is designed to examine feasibility and limitation of outsourcing in cooking Western food in a hotel, to interpret importance of outsourcing(eg. outside order, outside procurement, outside supply) in a broad sense in order to reinforce the core capacity in the cooking department, and to know whether the cooking human power is efficiently used and how much the chefs recognize outsourcing of food materials. As many companies conduct restructuring to cut down its size, the reduction of human power led the Western food cooking in the hotel to lower core capacities, lower quality, and lower efficiency. In addition, the sagging morale of chefs undermined creativity. To change from the traditional kitchen to an economic kitchen needs to look into importance of outsourcing, cognitive attitude of chefs, relation with outside suppliers. Here suggests performance of positive changes in the structure The study examined feasibility and limitation of outsourcing in the hotel kitchen as well as chefs' cognitive attitude toward outsourcing of food materials to reinforce core capabilities of the hotel kitchen. 1. Companies of outsourcing are selected according to variability of price conditions, flexibility of contract conditions, popularity of the outsourcing company, and reputation of the outsourcing company. 2. The importance of outsourcing in the Western food cooking is divided into 4 factors such as standard of selecting outsourcing companies, policies of cooking manu, quality of cooking, and quantity of cooking. 3. The most feasible section in outsourcing of food materials is a process of kneading flour for bread, which shows that many Western-food chefs expect to put higher possibility of outsourcing on the kneading. In other words, when it comes to confectionery and bakery, there are many outside expert processing companies supplying high quality products. In the order of outsourcing feasibility, sauce is followed by processed vegetable, garnish of main dish, and soup. The least feasible section in outsourcing of food materials is appetize. Appetize includes a concept of a improvised dish and needs speed. Due to its color, freshness, and sensibility of taste, the appetize plays a key role in the Western food cooking. 4. When outsourcing is taken in place, the highest risk is to lower the inner cooking skills. Therefore chefs in charge of the Western food sequently recognize both internal problems including storage of cooking skills, unstability of layoffs, and loss of cooperation between departments, and external problems including inferior goods, difficulty of differentiating manu, delay of delivery, and expiration date. It shows that most of the Western food chefs consider risks of the internal problems at first. 5. A effective outsourcing needs appropriate selection of outsourcing companies, maintenance of credibility, active communication, check and management of hygiene. However regardless of their position or career, chefs in charge of the Western food have the same cognitive attitude toward selecting successful outsourcing companies after the outsourcing system is enforced. The core of cooking, or a final stage in the full process of so-called artistic cooking, should be treated with insourcing. Reduction of several cooking processes resulted in shortened cooking time, increased efficiency, faster cooking, cutting the waiting-lines, and finally more room for customers. The outsourcing system can reduce or eliminate the following processes in cooking: buying various food materials, checking, storing, preparing, and processing. Especially in the Western food cooking department of a hotel, the outsourcing system should be enforced to make an economic kitchen and to efficiently manage it. Wow it's time to change from the traditional kitchen to an economic kitchen in the hotel cooking department. For that, the cooking department should become a small but strong organization by outsourcing except its core work.