• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.5
• /
• pp.8-13
• /
• 2012

The flexography ink has disadvantage in a deinking process because it tends to form too fine particles in alkali condition to be removed in flotation deinking. The influence of pH conditions on the particle size of phthalocyanine cyan ink used for flexo-printing was investigated to see the effect of pH conditions on flexography ink dispersion. Flexography ink particles prepared by grinding dried ink films were used in this experiment. Greater reduction of the ink particle size was noticed under alkaline pH condition, which was attributed to dissolution of resin component of the ink. Adsorption behavior of flexography ink onto pigment particles was examined using clay and talc as substrate pigments. Pretreatment of inorganic pigments with a cationic poly-DADMAC increased the surface adsorption of flexography ink particles, which improved the removal of the inks by centrifugal sedimentation of inorganic pigments. Most efficient removal of the ink particles was achieved when an optimal addition level of the cationic polymer was used for pretreatment of inorganic pigments, and this optimal addition level corresponds to the surface saturation point of the polyelectrolyte. Adsorption of flexography ink particles onto inorganic pigments improved the ink removal in flotation deinking since the pigment particles has the optimal particle size for flotation deinking.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.35 no.4
• /
• pp.34-41
• /
• 2003

The effect of wettability of deinking agents which formed with various nonionic surfactants against the pulp fibers and ink particles were studied, And the effect of flotation processes on the deinking were also investigated. The wettabilities of the deinking agents against the water and ink particles were measured by Washburn tube and sessile drop techniques, respectively. As the water absorption increased (i.e., hydrophilicity increased), the ink removal increased, which indicates that the ink removal is strongly affected by the detachment process due to the swelling of the pulp. Also, when the contact angle of air/ink/deinking agent increased, the hydrophobicity of the ink particles increased, the efficiency of the ink removal and the brightness increased.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.2
• /
• pp.123-129
• /
• 2020

We analyzed the drift current by charged particles according to the loading methods applied into a closed cell by electronic ink at a reflective-type display panel using an electrophoretic mechanism. For this experiment, various panels were fabricated with injection voltages for electronic ink taking values in the range -4~0 V. The size of each cell was 220 ㎛ × 220 ㎛ and height of the barrier rib was 54.28 ㎛. The electronic ink was fabricated by mixing electrically neutral fluid and single-charge white particles. Drift current was measured by moving charged particles. A biasing voltage of 6 V was applied to the display panel. As a result, the drift current was proportional to the injection voltage for electronic ink, but it decreased in case of an injection voltage above -3 V. Our experimentation ascertained that the concentration of charged particles injected into closed cells is controlled by the injection voltage and the selective injection of charged particles above movable q/m is possible.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.417-422
• /
• 2012

Copper nano particles have been considered as the materials for conductive ink due to its good thermal, electrical conductivity and low cost. However, copper nanoparticles oxidize easily, decreasing dispersion stability and electrical conductivity. Therefore, it is important to develop a method to minimize oxidation of copper nano particles to improve its dispersion stability property in copper nano ink. In this study, copper nano particles were coated with 1-Octanethiol VSAM(Vaporized Self Assembled Multilayers) to prevent oxidation and coated copper powders were dispersed in conductive ink successfully by studying its relationship of different chain length of solvents to 1-Octanethiol coating layer to fabricate nano ink. Various alcohol solvents, such as 1-Hexanol, 1-Octanol, and 1-Decanol were used. The coating layer was observed using FESEM and TEM. Furthermore, dispersion of copper nano particles in nano inks, was characterized using Turbiscan analyzer, viscometer, and contact angle measurement tool.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.969-971
• /
• 2007

The black/white electronic ink containing high mobility white nano particles and the organic black pigment particles dispersed in dielectric fluid were prepared. A charge control agent affects the electrophoretic zeta potentials of white particle, which show the maximum value in zeta potential. The electronic ink panel fabricated with the charged white particles and the black particles exhibits more than 15:1 contrast ratio at 10V.

• Applied Microscopy
• /
• v.52
• /
• pp.3.1-3.8
• /
• 2022

Our purpose in this study is to analyze the microstructural characteristics and constituent elements of inorganic substances added to the yellow ink and red ink pigments used in permanent makeup. We observed the microstructural properties of inorganic pigments added to the ink using a scanning electron microscopy (SEM) and analyzed the constituent elements of the inorganic pigment particles using an energy dispersive X-ray spectroscopy (EDX). In red wine-colored ink, cubic titanium dioxide with a diameter of 110 to 200 nm was the major component, and rod-shaped iron oxide was rarely observed. Most of the ingredients of taupe yellow ink were rod-shaped yellow iron oxide, and a small amount of cubic titanium dioxide was observed. Red wine-colored ink and taupe yellow ink contained lumps composed of titanium dioxide particles. In red wine-colored ink, lumps were formed by agglomeration. However, we observed that the surface of the lump composed of titanium dioxide in the taupe yellow ink had a smooth surface caused by external physical compression. The titanium dioxide particle mass which found in taupe yellow ink in this study is an artificial product. When this mass accumulates in the dermis, it may cause a color mismatch. Therefore, permanent makeup using fine pigments should be free of foreign substances that may cause trouble in the skin. In addition, there is a need to improve the quality of the ink so that the required color can be safe and long lasting in the dermis.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2010.04a
• /
• pp.7-7
• /
• 2010

Flotation deinking is a common practice for removing ink from recovered paper, and it is becoming a key process in many recycling paper mills. Flotation deinking was successfully introduced to the paper recycling industry in the 1980s, and its applications in wax removal, stickies control, and fiber fractionation have attracted great research interest. A successful flotation process has three major efficient subprocesses: the detachment of the ink particles from the fibers, the effective adhesion of the ink particles onto air bubble surfaces, and the removal of froth and ink particles from flotation cells. Surfactants can affect these subprocesses either positively or negatively. To understand how a surfactant can positively and negatively affect the flotation deinking process, the basic chemistry of surfactant in solution should be discussed.

• Textile Coloration and Finishing
• /
• v.15 no.5
• /
• pp.321-326
• /
• 2003

In order for disperse dye based ink to be fitted with the critical requirements of ink jet printing, this study was undertaken to investigate the effects of 6 different dispersants on the milling efficiency of insoluble dye particles and dispersion stability of the final ink. It was found that a polystyrene dispersant with high molecular weight exerted relatively better dispersion stability which may be associated with its steric stabilization effect in the ink solution.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.865-867
• /
• 2009

In this paper, we describe the fabrication of nano-scale ink particles with narrow size distribution to offer high optical density in electrophoretic display applications. Charged white ($TiO_2$ and polyester) and black (carbon black and polyester) nano size ink particles in size range of 200 ~ 700nm were made successively using modified non-aqueous base emulsion process. The EPD showed white reflectance of 58% and saturation voltage of ${\pm}10V$.

• Journal of Aerospace System Engineering
• /
• v.12 no.6
• /
• pp.1-8
• /
• 2018

ACF, which is used for the transparent electrode film is manufactured by the thermocompression method with conductive particles. However, the method has disadvantages since there are many wasted materials and the process is complex. To overcome the demerits of the conventional method, EHD printing technology with conductive particles ink is proposed. The line thickness of patterning is influenced by the characteristics of the inks and the printing conditions. Therefore, it is salient to find the most conducive conditions for the micro patterning. In this paper, the ink with conductive particles was manufactured, and the patterning results were obtained by varying the nozzle thickness and the flow rate. The electrical conductivity according to the ejection of the particles ink is obtained.