• Microbiology and Biotechnology Letters
• /
• v.19 no.5
• /
• pp.514-520
• /
• 1991

Direct synthesis of cyclodextrin (CD) from extruded insoluble corn starch without liquefaction procedure using cyclodextrin glucanotransferase (CGTase) was carried out. Increased CD production rate and yield were achieved in heterogeneous enzyme reaction system containing extruded corn starch compared with those of conventional system employing liquefied or partially cyclized starch. At extruded starch concentration of 100 g/l the CD concentration and conversion yield were reached up to 54 g/l and 0.54, respectively. High purity of $\alpha \beta \gamma$-CDs without accumulation of undesirable malto-oligosaccharides was produced, furthermore, the residual extruded starch was easily separated by centrifugation from reaction mixture, whlch will facilitate the purification procedure. Granular structure of extruded starch was observed by SEM to investigate enzyme reaction mechanism. Supplemental addition of $\alpha$-amylase enhanced slightly the initial CD production rate, but it decomposed produced CD at the late stage. Various! extruded raw starches, such as, corn, rice, and barley were also suitable substrates for CD production.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.6
• /
• pp.563-569
• /
• 1999

The numerical simulation method was utilized to investigate the optimal condition for synthesizing ultrafine SiC powders by using $TMS[Si(CH_3)_4]-H_2$ gaseous mixtures in the horizontal reactor. As a result of the theoretical analysis, the conversion percentage of TMS source was increased with increasing reaction temperature, however, which was decreased with increasing H$_2$flow rate. Though the SiC particles concentration synthesized was decreased with increasing the reaction temperature due to the higher collision rate in the gas phase, they were increased with increasing the H$_2$flow rate and TMS concentration. The SiC particle size showed a tendency to become larger as the reaction temperature and the initial TMS concentration were increased and smaller as the H$_2$ flow rate was increased. The variation of experimental particle size with the reaction temperature, H$_2$flow rate and TMS concentration was agreed with the theoretical results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.163-166
• /
• 1998

The mechanism of methane sensing by Pd-SiC diode was investigated over the temperature range of 400~$600^{\circ}C$. The effects or methane gas reaction on the parameters such as barrier height, initial rate of methane gas reaction are investigated. The methane gas reaction kinetics on the device are also discussed. The physical and chemical mechanism responsible for methane detection are proposed. Analysis of steady-state reaction kinetics using I-V method confirmed that methane gas reaction processes are responsible for the barrier height change in the diode.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.11 no.1
• /
• pp.69-75
• /
• 2013

The recovery of Zr from Zircaloy-4 (Zry-4) cladding hulls was demonstrated to investigate the effect of the oxidation process on the reaction rate of the chlorination reaction. In chlorination reaction experiments performed for 6 h, where reaction products were collected every 2 h, it was observed that a significant decrease in the reaction rate was caused by the oxidation process ($500^{\circ}C$, 10 h under an air atmosphere) within the reaction period of 0 - 2 h. The amount of reaction residue increased from 0.95 to 1.65wt% of initial weights in the fresh and Zry-500-10 (Zry-4 hulls oxidized at $500^{\circ}C$ for 10 h under an air atmosphere) hulls, respectively. The purity of the recovered Zr was identical at 99.61wt% for the fresh Zry-4 and Zry-500-10 hulls. Quantitative analysis of the chlorination reaction rate was performed by varying the reaction time from 0.5 to 1.0, 2.0, and 4.0 h. The fitting results showed that the relationship between weight loss and reaction time can be interpreted by a linear line with a slope of 23.35wt%/h for the fresh Zry-4 case, while two linear lines were necessary to fit the results of Zry-500-10. In addition, the slope values were 17.12 and 27.16wt%/h for (0 - 20) and (20 - 100)wt% loss regions, respectively.

• Journal of Microbiology and Biotechnology
• /
• v.10 no.1
• /
• pp.99-102
• /
• 2000

To establish optimal conditions for esterification by Candida cylindracea, lipase reactions were performed simultaneously, separately, or individually in the varying initial rates of $0.014-0.060\mu$mole free fatty acids consumed min-1g-1. The reactants which were conditioned at aw of 0.12 gave the highest initial rate of esterifying $0.060\mu$mole free fatty acids consumed min-1g-1. These results suggest that the esterifying activity of lipase in an organic system depends on the transfer of available water within the reaction system.

• Microbiology and Biotechnology Letters
• /
• v.32 no.1
• /
• pp.84-90
• /
• 2004

Diglyceride (DG) was prepared by reaction of soybean oil and glycerol in the presence of lipase. The initial rate of DG production was greatly affected by the amount of lipase. However the DG content at equilibrium was hardly affected by the amount of lipase added to the reaction mixture. The initial rate of FFA formation was highly affected by the moisture content between 0.5 and 2.3%, but at higher water content (3.3-5.2%), there was a small increase in the rate. And DG content at equilibrium slowly increased with the increase of the water content in glycerol up to 4.4%. However, there was a sharp decrease in DG content at higher water content (5.2-6.4%) due to higher free fatty acid production. The highest yield of DC was obtained at the temperature ranges of 30-5$0^{\circ}C$. The final yield of DG was not dependent on the glycerol (GL) to triglyceride (TG) molar ratio. However, at the molar ratio of 0.75:1 (GL/TG), the enzyme-catalyzed reaction was highly efficient and utilized all the glycerol. In optimized conditions for glycerolysis a yield of approximately 45% DG was obtained. 66% of total DG was 1,3-DG.

• Korean Journal of Materials Research
• /
• v.26 no.8
• /
• pp.406-411
• /
• 2016

In order to reuse the photocatalyst and enhance the photolysis efficiency, we have used atmospheric pressure dielectric barrier discharge (APDBD) to clean and activate $TiO_2$ powder. The photocatalytic activity of the $TiO_2$ powder before and after APDBD treatment was evaluated by the degradation of methylene blue (MB) in aqueous solution. The apparent reaction rate constant of photolysis of the first sample of reused $TiO_2$ cleaned by APDBD improved to a level up to 0.32h-1 higher than the 30 % value of the initial $TiO_2$ powder. As the number of photolysis reactions and APDBD cleanings increased, the apparent rate constants gradually decreased; however, the fourth photolysis reaction still showed a value that was greater than 10% of the initial value. In addition, APDBD treatment enhanced the process by which $TiO_2$ effectively adsorbed MB at every photolysis stage.

• KSBB Journal
• /
• v.19 no.1
• /
• pp.38-41
• /
• 2004

Enantioselective hydrolysis for the producing chiral epichlorohydrin from its racemic substrate was investigated using epoxide hydrolase activity of Rhodosporidium toruloides SJ-4. The effects of reaction parameters including pH, temperature, initial substrate concentration on initial hydrolysis rate and enantioselectivity were analyzed and optimized. The addition of detergent, Tween 20, enhanced the hydrolysis rate and enantioselectivity. Chiral (R)-epichlorohydrin with high optical purity (＞99% ee) and yield of 25% (theoretically 50% maximum yield) was obtained from its racemate of 20 mM.

• Journal of Korean Society on Water Environment
• /
• v.20 no.1
• /
• pp.86-92
• /
• 2004

Lab-scale experiments have been carried out to investigate ammonia stripping with a modified spray tower for removing ammonia nitrogen from swine wastewater. The operating conditions such as initial pH, temperature, air flow, hole size of distributor determining the diameter of water drops, and influent solids concentration were closely examined focusing on removal efficiency of ammonia. As a result of the experiment, in order to achieve high rate of ammonia removal by the air stripping system, the air flow rate must be supplied at high rate with sufficiently high initial pH, temperature. The optimum operating condition to meet the residual ammonia concentration of 300 mg/L was the initial pH of 11.0 at $35^{\circ}C$ with the air flow rate of 20 L/min. It also showed that the smaller hole size is, the higher removal rate of ammonia is expected. However, when used a small sized distributor (2 mm), the flooding problem at the upper column occurred due to clogging of the hole. With regard to the influent solids concentration, it was showed that the lower concentration of solids, the higher removal rate of ammonia. The removal of particulate materials in influent led to improve the removal efficiency of ammonia, rather than to control the operating condition including initial pH, temperature, and air flow. The empirical correlation between KLa and operating parameters would be driven as, $K_{La}=(0.0003T-0.0047){\cdot}G^{0.3926}{\cdot}L^{-0.5169}{\cdot}C^{-0. 1849}$. The calculated $K_{La}$ from proposed formula can be used effectively to estimate the optimum reaction time and to calculate the volume of modified spray tower system.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.88-92
• /
• 2012

Decrosslinking of crosslinked polypropylene(XLPP) in supercritical methanol was investigated compared with that of crosslinked polyethylene(XLPE). Effect of reaction temperature and initial gel contents was studied using a batch reactor. Gel contents of samples before and after reaction were measured for quantitative analysis. As reaction temperature and initial gel contents increased, the decrosslinking rate increased. The rate of decrosslinking reaction is dependent linearly on the gel contents. Experimental results indicated that the decrosslinking of XLPP was faster than that of XLPE, and it was confirmed quantitatively by the calculation of kinetic constants. In conclusion, it is considered that XLPP has better recyclability than XLPE.