• Elastomers and Composites
• /
• 제56권3호
• /
• pp.172-178
• /
• 2021

The wear behavior of styrene-butadiene rubber (SBR) and butadiene rubber (BR) was investigated using a blade-type abrader with a steel blade (SB), Ti-coated tungsten carbide blade (TiB), or zirconia blade (ZB). The wear rate of SBR against SB and TiB decreased with increasing number of revolutions because of the blunting of the blades during wear. However, the wear rate of SBR against ZB remained nearly constant with little blade blunting. Generally, the wear rate of BR was largely unaffected by the blade material used for abrasion. The wear rate and frictional coefficient of SBR were found to be higher than those of BR at similar levels of frictional energy input. A power-law relationship was found between the wear rate and frictional energy input during abrasion. A well-known Schallamach pattern was observed for SBR, while a much finer pattern was observed for BR. The blade material affects the wear rate of the rubbers because the macromolecular free radicals and blade tend to undergo mechano-chemical reactions. The inorganic ZB was found to be the most inert for such a mechanism.

• Journal of Electrochemical Science and Technology
• /
• 제12권2호
• /
• pp.272-278
• /
• 2021

In this study, high nickel layered LiNi_0.8Co_0.1Mn_0.1O₂ cathode materials for lithium-ion batteries were modified by yttrium doping and poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) coating. The effects of yttrium doping and PEDOT:PSS coating on the structural and electrochemical properties of the LiNi_0.8Co_0.1Mn_0.1O₂ cathode material were investigated and compared. The substitution of nickel with an electrochemically inert yttrium was confirmed to be successful in stabilizing the layered structure framework. Moreover, coating the surfaces of the LiNi_0.8Co_0.1Mn_0.1O₂ particles with a conductive polymer, PEDOT:PSS, improved the capacity retention, thermal stability, and impedance of the cathode material by increasing its ionic and electric conductivities.

• FOCUS: LIFE SCIENCE
• /
• 제1호
• /
• pp.4.1-4.15
• /
• 2024

The Avantor® ACE® UltraCore series encompasses High Performance Liquid Chromatography (HPLC) and Ultra High Performance Liquid Chromatography (UHPLC) columns designed to deliver high throughput and high-efficiency ultra-fast separations. Utilizing ultra-inert solid-core silica particles with monodisperse particle distribution, these columns combine the high efficiency of UHPLC with the operability of HPLC instrumentation, yielding lower backpressure and high-resolution separations suitable for a broad spectrum of analytes. The Avantor® ACE® UltraCore range includes three primary product types: • UltraCore BIO: Designed for large biomolecules (≥5 kDa), these columns offer exceptional performance in separating biologically derived compounds. • UltraCore: Ideal for standard small organic molecules, providing rapid separations for both synthetic and natural mixtures. • UltraCore Super: Equipped with encapsulated bonding technology for small organic molecules in extreme pH conditions, optimal for high pH buffer requirements. The Avantor® ACE® UltraCore columns present a versatile and high-efficiency solution for chromatographic separation needs, accommodating a wide range of molecular sizes and providing enhanced resolution and reduced analysis time. Their adaptability to both HPLC and UHPLC systems, combined with the advantages of solid-core technology, makes them an invaluable tool in analytical and preparative chromatography.

• 한국재료학회지
• /
• 제25권12호
• /
• pp.719-726
• /
• 2015

For a decade, solution-processed functional materials and various printing technologies have attracted increasingly the significant interest in realizing low-cost flexible electronics. In this study, Cu nanoparticles are synthesized via the chemical reduction of Cu ions under inert atmosphere. To prevent interparticle agglomeration and surface oxidation, oleic acid is incorporated as a surface capping molecule and hydrazine is used as a reducing agent. To endow water-compatibility, the surface of synthesized Cu nanoparticles is modified by a mixture of carboxyl-terminated anionic polyelectrolyte and polyoxylethylene oleylamine ether. For reducing the surface tension and the evaporation rate of aqueous Cu nanoparticle inks, the solvent composition of Cu nanoparticle ink is designed as DI water:2-methoxy ethanol:glycerol:ethylene glycol = 50:20:5:25 wt%. The effects of poly(styrene-co-maleic acid) as an adhesion promoter(AP) on rheology of aqueous Cu nanoparticle inks and adhesion of Cu pattern printed on polyimid films are investigated. The 40 wt% aqueous Cu nanoparticle inks with 0.5 wt% of Poly(styrene-co-maleic acid) show the "Newtonian flow" and has a low viscosity under $10mPa{\cdots}S$, which is applicable to inkjet printing. The Cu patterns with a linewidth of $50{\sim}60{\mu}m$ are successfully fabricated. With the addition of Poly(styrene-co-maleic acid), the adhesion of printed Cu patterns on polyimid films is superior to those of patterns prepared from Poly(styrene-co-maleic acid)-free inks. The resistivities of Cu films are measured to be $10{\sim}15{\mu}{\Omega}{\cdot}cm$ at annealing temperature of $300^{\circ}C$.

• 한국주조공학회지
• /
• 제41권3호
• /
• pp.235-240
• /
• 2021

진공 가스분사법으로 제조된 Fe₇₅B₁₃P₅Nb₂Hf₁C₄ 합금의 응고중 액상의 크기와 이에 따른 냉각속도의 변화가 정출상의 형성에 미치는 영향에 대한 고찰을 하였다. 고온 액상에서 동일한 조건으로 응고된 서로 다른 크기의 액상이 구형의 분말형태로 응고될 때 크기에 따른 임계냉각속도의 차이를 계산하였으며, 액상의 평균 반지름이 3배정도 크기 차이가 날 경우 고상으로 변태할 때 임계냉각속도가 13.5배까지 차이가 나는 것을 알 수 있었다. 이러한 임계냉각 속도의 차이에 따른 정출상의 형성과 정출상의 형태와 크기에 따른 탄화물의 형성 거동을 조사하여 열역학 계산으로 예측된 결과와 비교 분석하였으며, 분말입자의 크기가 20~45 마이크론일 경우 Hf과 Nb이 포함된 MC타입의 탄화물이 초정으로 형성 되는 것을 알 수 있었으며 이때 Hf과 Nb의 비율은 합금의 조성 및 냉각속도에 따라 변화됨을 관찰 할 수 있었다.

• 한국산업보건학회지
• /
• 제8권2호
• /
• pp.209-223
• /
• 1998

The aim of this study was to evaluate welders' exposure to hexavalent chromium (Cr(VI)) and nickel (Ni) during welding operations in a Korean shipyard. The airborne Cr(VI) and Ni concentrations were measured during metal inert gas (MIG) welding on mild and stainless steel, and manual metal arc (MMA) welding on mild steel. The geometric mean (GM) of Cr(VI) concentrations inside the welding helmet during MIG welding on mild steel were $0.0018mg/m^3$ inside a ship section, and $0.0015-0.0026mg/m^3$ at the welding shops. All of the personal breathing zone air samples were below the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Value ($TLV^{(R)}$) of $0.01mg/m^3$. Conversely, eighty-eight percent(21 of 24) of the personal breathing zone air samples exceeded the National Institute for Occupational Safety and Health (NIOSH) recommended exposure limit of $0.001mg/m^3$. Ni was not detected on 20 of 23 air samples collected during MIG welding on mild steel. The three Ni samples above the limit of detection ranged from 0.015 to $0.044mg/m^3$. The GM of Cr(VI) concentrations during MMA welding on mild steel were $0.0013mg/m^3$, but Ni was not detected in the air samples during this operation. It is assumed that the airborne Cr(VI) and Ni during mild steel welding were derived from the base metals which contained about 0.03% Cr and 0.03% Ni. The GM of airborne total Cr, Cr(VI) and Ni concentrations during MIG welding on stainless steel were 4.02, 0.13 and $0.86mg/m^3$, respectively, and the levels of Cr(VI) and Ni were above the ACGIH-$TLV^{(R)}$. Cr(VI) comprised about 35.5% of the total chromium(Cr) from MIG welding on mild steel, and about 8.4% of total Cr from MIG welding on stainless steel. The ratios of Cr(VI) to total Cr were significantly different among welding shops. It was concluded that welders were exposed to high levels of Cr(VI) and Ni during welding on stainless steel, and were exposed to low levels of Cr(VI) even during welding on mild steel.

• Journal of Preventive Medicine and Public Health
• /
• 제31권3호
• /
• pp.414-423
• /
• 1998

Metal fume fever has been known as an occupational disease is induced by intense inhalation of fresh metal fume with a particle size smaller than $0.5{\mu}m\;to\;1{\mu}m$. The fumes originate from heating metals beyond their boiling point, as happens, for example, in welding operations. Oxidation usually accompanies this process. In most cases, this syndrome is due to exposure to zinc oxide fumes; however, other metals like copper, magnesium, cadmium, manganese, and antimony are also reported to produce such reactions. Authors report a case of metal fume fever suspected to be associated with copper fume inhalation. The patient was a 42-year-old male and was a smoker. He conducted inert gas tungsten arc welding on copper-coated materials without safety precautions such as a protective mask and adequate ventilation. Immediately after work, he felt metallic taste in his mouth. A few hours after welding, he developed headache, chilling sensation, and chest discomfort. He also complained of myalgia, arthralgia, feverish sensation, thirst, and general weakness. Symptoms worsened after repeated copper welding on the next day and subsided gradually following two weeks. Laboratory examination showed a transient increase of neutrophil count, eosinophilia, elevated erythrocyte sedimentation rate, and positive C-reactive proteinemia. Blood and urine copper level was also increased compared to his wife. Before this episode, he experienced above complaints several times after welding with copper materials but welding of other metals did not produce any symptoms. It was suggested that copper fume would have induced metal fume fever in this case. Further investigations are needed to clarify their pathogenic mechanisms.

• 한국자기학회지
• /
• 제13권2호
• /
• pp.47-52
• /
• 2003

DC 마그네트론 스파터법과 RLSA(Radial Line Slot Antenna)을 이용한 마이크로파 여기 프라즈마를 이용하여 Ta/Cu/Ta/NiFe/Cu/Mn$_{75}$Ir$_{25}$/ $Co_{70}$Fe$_{30}$/Al-oxide 구조의 접합을 제조한 후, contact-mode AM(Atomic Force Microscope)을 이용하여 Al 산화막의 국소전도 특성의 평가를 수행하였다. AFM 동시전류측정으로부터, 얻어지는 표면상과 전류상은 대응하지 않는다. 국소 전류-전압(I-V)의 측정 결과, 전류상은 절연층의 barrier height의 분포를 나타내고 있다는 것을 알았다.다.다.

• 한국결정성장학회지
• /
• 제27권1호
• /
• pp.28-33
• /
• 2017

SiC 섬유는 $1800^{\circ}C$까지 불활성과 공기 분위기에서 융해나 산화 문제 없이 사용할 수 있다. SiC 섬유는 분진 필터링 공정의 백필터로 상업화된 산업용 백 필터보다 훨씬 높은 온도인 $500^{\circ}C$ 이상의 온도에서 사용이 가능하다. 하지만 제강 산업과 화력발전소의 극한 환경에서 미세 분진과의 반응으로 인한 SiC 섬유의 열화에 대한 연구는 부족하다. 따라서 본 실험에서는 SiC 섬유를 제강 분진, 화력발전소 분진과 $500^{\circ}C$ 이상의 고온에서 반응시켜 섬유 표면의 열화된 형상을 SEM으로 관찰하고 섬유 표면 및 내부로의 산소 확산의 정도를 EDS로 분석하였다.

• 열처리공학회지
• /
• 제9권1호
• /
• pp.1-11
• /
• 1996

Mechanical alloying is an effective process to finely distribute inert dispersoids in an Al-TM(TM is a transition metal) system. It has been considered that high melting point aluminides are formed by precipitation from supersaturated Al(Ti) powder. This analysis is based on the fact that much higher content of TM than the solubioity can be dissolved in alpha aluminum during the high energy ball milling. Thus, decomposition behavior of Ti in the Al(Ti) was considered very important. But it is confirmed that the higher portion of Ti than Al(Ti) solid solution is existed as nano-sized Ti particles in the MA powders by high energy ball nilling from the XRD spectrum and TEM analysis in this study. Therefore, the role of undissolved TM particles affect the formation of aluminides should be suitably considered. In this study, we present experimental observation on the formation of $Al_3Ti$ fron mechanical alloyed Al-Ti alloys in the hyperperitectic region. This study showed that, in the mechanically alloyed Al-20wt%Ti specimen, intermediate phase of cubic $Al_3Ti$ and tetragonal $Al_{24}Ti_8$ formed at $300{\sim}400^{\circ}C$ and $400{\sim}500^{\circ}C$, respectively, before the MA state reaches to equilibrium at higher temperatures. The formation behavior of $Ll_2-Al_3Ti$ is interpreted by interdiffusion of Al and Ti in solid state based on the fact that large amount of nano-sized Ti particles exist in the milled powder. Present analysis indicated undissolved Ti particles of nanosize should have played an important role initiation the formation of $Al_3Ti$ phase during annealing.