• Membrane Journal
• /
• v.24 no.4
• /
• pp.325-331
• /
• 2014

We synthesized novel polyimides with high gas permeability and selectivity for application of on board inert gas generation system (OBIGGS). 2,2-bis(3,4-carboxylphenyl) hexafluoropropane dianhydride (6FDA) and two kinds of amines with high permeability and solubility were used to prepare the novel polymide. 2,3,5,6-Tetramethyl-1,4-phenylenediamine (TMPD) was used to improve gas permeability and various kinds of diamines were used to improve the gas selectivity respectively. The polyimide copolymers were synthesized by commercial chemical imidization method and their average molecular weights were over 100,000g/mol. The glass temperature ($T_g$) and the thermal degradation temperature were characterized using differential scanning calorimeter (DSC) and thermogravimetric analysis (TGA). The synthesized copolymers showed high $T_g$ over $300^{\circ}C$ and high thermal degradation temperature over $500^{\circ}C$. The gas permeation properties were measured by time-lag equipment. Although general polyimides showed very low gas permeability, synthesized polyimide copolymer showed high $O_2$ permeability of 36.21 barrer with high $O_2/N_2$ selectivity around 4.1. From this result, we confirm that these membranes have possibility to apply to OBIGGS.

• Membrane Journal
• /
• v.28 no.6
• /
• pp.406-413
• /
• 2018

In OBIGGS, a small amount of ozone in the atmosphere damages the polymer membrane. Therefore, the ozone removal device is installed at the front end to prevent the damage of the membrane by reducing the concentration of ozone in the gas delivered to the membrane. In this study, two hollow fiber membranes, PI and PSf, used to fabrication hollow fiber module with an effective membrane area of $6.37cm^2$ for gas separation in OBIGGS. The ozone concentration in the chamber was maintained at 2-3 ppm. The gas was continuously supplied into the module by using a pump. The gas permeation characteristics and the tensile strength were evaluated as a function of ozone exposure time. The PI-based hollow fiber membrane showed only 20% reduction in the transmittance, and remained its original uniformity without any significant changes. However, when PSf type hollow fiber membranes were used, the permeability decreased by more than 80% and the tensile strength decreased by more than 70%.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.6
• /
• pp.70-78
• /
• 2012

The Annals of Joseon Dynasty, which recorded governmental affairs for 472 years (AD 1392-1863) during the Joseon dynasty is an representative paper cultural heritage in Korea. Being recognised their authenticity and values they were designated as the No 151 national treasure of Korea in 1973 and registered as 'The Memories of the World' by UNESCO in 1997. Unusually, some volumes of the Annals were treated by beeswax for the permanent preservation. However, the examinations on the deterioration of the beeswax-treated volumes had been exposed the serious damage than the untreated volumes. In particular, the larger amount of beeswax were worst in deterioration condition. In order to solve these problems, NRICH(National Research Institute of Cultural Heritage) of Korea launched the investigation study for the conservation of beeswax-treated volumes of the Annals. Now then, the five study areas have been set up; 1) to understand the damaged condition of the Annals; 2) to analyse the raw materials and production techniques; 3) to test the degradation degree using the duplication samples for understanding the aging factors and mechanism; 4) to develop the conservation techniques through dewaxing and thereafter strengthening the base paper of Hanji; 5) to develop the long-term storage technique using inert gases. On the basis of outcomes from this study, NRICH will plan to establish the systematic conservation and management plan for the beeswax-treated volumes of the Annals in future.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.7 no.2
• /
• pp.34-41
• /
• 2011

Wrought nickel-base superalloys are being considered as the structural materials in very-high temperature gas-cooled reactors. To understand the effects of impurities, especially oxygen, in helium coolant on the mechanical properties of Alloy 617, creep tests were performed in high temperature flowing He environments with varying $O_2$ contents at 800, 900, and $1000^{\circ}C$. Also, creep life in static He was measured to simulate the pseudo-inert environment. Creep life was the longest in static He, while the shortest in flowing helium. In static He, impurities like $O_2$ and moisture were quickly consumed by oxidation in the early stage of creep test, which prevented further oxidation during creep test. Without oxidation, microstructural change detrimental to creep such as decarburization and internal oxidation were prevented, which resulted in longer creep life. On the other hand, in flowing He environment, surface oxides were not stable enough to act as diffusion barriers for oxidation. Therefore, extensive decarburization and internal oxidation under tensile load contributed to premature failure resulting in short creep life. Limited test in flowing He+200ppm $O_2$ resulted in even shorter creep life. The oxidation samples showed extensive spallation which resulted in severe decarburization and internal oxidation in those environments. Further test and analysis are underway to clarify the relationship between oxidation and creep resistance.

• Applied Chemistry for Engineering
• /
• v.7 no.5
• /
• pp.813-822
• /
• 1996

In order to reduce carbon dioxide, one of the major greenhouse gases, a new type of copolymer, poly(alkylene carbonate) has been synthesized. The alternating copolymers have been obtained from carbon dioxide and various epoxides with zinc carboxylate as a catalyst. The number-average molecular weight of the polymer is about 50,000 and polydispersity is rather broad(5~10). The polymers are amorphous, and glass-clear materials that exhibit unusually facile and clean thermal decomposition behavior. Complete decomposition with no carbon residue is observed at elevated temperature even in an inert atmosphere. Terpolymers with bulkier epoxides improve the physical properties of the copolymer with simple epoxides. The decomposition properties of the polymer provide versatile applications such as ceramic, metal, and electronic binders and lost-foam casting. Further application of the polymer for the barrier film or the plasticizer will be investigated.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.14 no.3
• /
• pp.229-234
• /
• 1985

The effect of packaging on the quality of dried anchovy was investigated, when packed with various materials and stored at different conditions. In cases of nitrogen gas substitution or addition of antioxidant, the reaction rates of lipid oxidation, the loss of available lysine and browning of the samples sealed in aluminum laminated film bag were lower than those packed in kraft paper or polyethylene film bag while the samples without gas substitution did not reveal any great differences in the rate of the reactions. The shelf-lives of the samples computed as a function of lipid oxidation were 90, 98 and 137 days at the storage of $35^{\circ}C$ for the packages of kraft paper, polyethylene and aluminum film respectively. And those at $55^{\circ}C$ storage for the same samples were 47, 51 and 77 days. The half-lives of available lysine loss were 227, 209 and 312 days at $35^{\circ}C$: 83, 83 and 147 days at $55^{\circ}C$ for the samples respectively. And the shelf-lives determined as a function of browning reaction were 26, 27 and 49 days at $55^{\circ}C$. The predicted shelf-lives at $25^{\circ}C$ as a function of lipid oxidation were 130, 140, and 189 days for kraft paper, polyethylene and aluminum laminated film packaging: 207, 229 and 246 days for the browning reaction, and 363, 339 and 415 days for the loss of available lysine. The results suggest that the protective effect of packaging on the reactions of lipid oxidation and browning could not be aided unless the air was expelled or replaced to inert gas.

• Journal of Powder Materials
• /
• v.13 no.4 s.57
• /
• pp.285-289
• /
• 2006

Co-Fe-Ni-B-Si-Cr based amorphous strips containing nitrogen were manufactured via melt spinning, and then devitrified by crystallization treatment at the various annealing temperatures of $300^{\circ}C{\sim}540^{\circ}C$ for up to 30 minutes in an inert gas $(N_2)$ atmosphere. The microstructures were examined by using XRD and TEM and the magnetic properties were measured by using VSM and B-H meter. Among the alloys, the amorphous ribbons of $Co_{72.6}Fe_{9.8}Ni_{5.5}B_{2.4}Si_{7.1}Cr_{2.6}$ containing 121 ppm of nitrogen showed relatively high saturation magnetization. The alloy ribbons crystallized at $540^{\circ}C$ showed that the grain size of $Co_{72.6}Fe_{9.8}Ni_{5.5}B_{2.4}Si_{7.1}Cr_{2.6}$ alloy containing 121 ppm of nitrogen was about f nm, which exhibited paramagnetic behavior. The formation of nano-grain structure was attributed to the finely dispersed Fe4N particles and the solid-solutionized nitrogen atoms in the matrix. Accordingly, it can be concluded that the nano-grain structure of 5nm in size could reduce the core loss within the normally applied magnetic field of 300A/m at 10kHz.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.124-129
• /
• 2017

In this study, we report characteristics of friction stir welding (FSW) technique applied to Al-6005-T6 extruded sheets, which is a common material for railway car bodies. With the welding speed fixed at 300 mm/min, the revolution per minute (RPM) of the rotating tool was varied from 600 to 1800 RPM, with the aim at evaluating the resultant microstructure and mechanical behaviors. Comparison is also made with the conventional Metal Inert Gas (MIG) welding technique. Unlike MIG, no micro-voids were observed for FSW specimens. Hardness measurement revealed that the increased heat input by increasing RPM results in widened heat affected zone (HAZ) and decreased hardness for HAZ due to grain coarsening. Hardness results for the nugget do no show difference. During tensile tests, specimens fractured at HAZ, and increasing rpm led to decrease of the yield stress and tensile stress for the selected RPM range, which is considered to be due to the grain coarsening for HAZ.

• Journal of the Korean Society of Safety
• /
• v.31 no.2
• /
• pp.18-25
• /
• 2016

The incandescent lamp is an electric light fixture with a tungsten filament heated to a high temperature, by passing an electric current through it, until it glows with visible light. The hot filament is protected from oxidation with a glass bulb that is filled with inert gas. The incandescent lamp has fire risk when combustible materials are close to its glass bulb. Because its lamp has the property which converts 90~95 percents of the electric power to heat energy. 2015 national fire statistics show that fires caused by lighting fixtures were 652 cases, and incandescent lamps(44 cases) and halogen lamps(53 cases) accounted for 15 percents in those of high heating light fixtures. Since incandescent lamp fires account for about 45 percents in the high heating light fixture, we could not overlook the fire risks by the incandescent lamp. Although many studies related with those have been conducted, incandescent lamp fires are continuously occurred. This study was carried out to study the fire risk of ignition of wood due to radiant heat of incandescent lamp. Radiant heat flux of the incandescent lamp was predicted by applying point source model, and critical distance for ignition of wood was calculated by applying integral model. The results from this study could applied to fire prevention activities related to light bulb, and it could be used in fire cause investigations related to radiant heat of incandescent lamp.

• Transactions on Electrical and Electronic Materials
• /
• v.3 no.2
• /
• pp.10-15
• /
• 2002

In this paper, the electrical characteristics of fabricated p+-n junction diode are demonstrated and interpreted with different theoretical calculations. Dopants distribution by boron ion implantation on silicon wafer were simulated with TRIM-code and ICECaEM simulator. In order to make electrical activation of implanted carriers, thermal annealing treatments are carried out by RTP method for 1min. at $1000^{circ}C$ under inert $N_2$ gas condition. In this case, profiles of dopants distribution before and after heat treatments in the substrate are observed from computer simulations. In the I-V characteristics of fabricated diodes, an analytical description method of a new triangular junction model is demonstrated and the results with calculated triangular junction are compared with measured data and theoretical calculated results of abrupt junction. Forward voltage drop with new triangular junction model is lower than the case of abrupt junction model. In the C-V characteristics of diode, the calculated data are compared with the measured data. Another I-V characteristics of diodes are measured after proton implantation in electrical isolation method instead of conventional etching method. From the measured data, the turn-on characteristics after proton implantation is more improved than before proton implantation. Also the C-V characteristics of diode are compared with the measured data before proton implantation. From the results of measured data, reasonable deviations are showed. But the C-V characteristics of diode after proton implantation are deviated greatly from the calculated data because of leakage currents in defect regions and layer shift of depletion by proton implantation.